Aerus BEYOND SANCTUAIRY Bedienungsanleitung

65-00584 VA-00797

Owner’s Manual

ELECTRONIC AIR PURIFICATION SYSTEM

CAUTION: Read manual carefully for proper procedures and operation.

CONTENTS

on your purchase of a Beyond by Aerus

Sanctuairy air purification enhancement

system. This unit is designed to be installed

into an existing HVAC system by a licensed

HVAC contractor. Please follow all service

procedures outlined in this manual. Use only

genuine Beyond by Aerus replacement parts

available from your Beyond by Aerus Dealer.

CONGRATULATIONS . . .

Specifications.................................2

About Beyond by Aerus Sanctuairy ..........2

Product Contents.............................3

Installation Hardware.........................3

Replacement Parts ...........................3

Recommended Installation Tools.............3

Installation Requirements ....................4

Metal Ductwork Installation ..................5

Fiberglass Ductwork Installation..............6

Maintenance/UV Lamp Indicator............12

Warranty ....................................12

Changing the ActivePure® Cell ..............13

Changing the Ballast ........................14

Electrical:

• Input: AC 100-240V 50/60Hz 0.4A

• Output: DC 24V 1A

Mechanical:

• Distribution via air handler.

Dimensions:

• 8.5” x 8.5” x 11”

(21.59cm x 21.59cm

x27.94cm)

Weight: 3 pounds (1.2 kg.)

Operating Temperature:

• 32-200°F (93°C)

Coverage:

• Up to 2000 ft

Nominal, 3000 ft

Maximum

Warranty:

• Limited 5 years.

SPECIFICATIONS

The Beyond by Aerus Sanctuairy is

easily mounted into the supply side of air

conditioning and heating system air ducts

where many problems can start.

ActivePure® Cell (Ozone-Free) Item # 49780

Please record the name and phone number of your

Beyond by Aerus Dealer:

Name_______________________________________

Phone ______________________________________

Please record the name and phone number of your

Independent HVAC Contractor:

Name_______________________________________

Phone ______________________________________

Please record your product serial number:

Serial #______________________________________

Location for Protective Earth Line.

WARNING! - UV Light in operation.

Disconnect unit from power supply

before servicing. Failure to follow

warnings may result in severe eye

damage and electrical shock.

WARNING! - This unit must be installed

by a licensed HVAC contractor. Failure to

do so will void warranty of the product.

WARNING! - To prevent damage to the

unit, operating environment temperature

must never exceed 200˚F (93°CC).

WARNING! -This unit must never be

used with an extension cord.

WARNING! - Do not connect this unit

to any voltage source above 32 volts.

Doing so will cause damage to the unit.

Safety

Switch

REPLACEMENT PARTS

Base Unit

ActivePure® Cell (Ozone-Free)

Item # 49780

Ballast

Item # 49776

Power Cord

Item # 49782

INSTALLATION HARDWARE SUPPLIED

UV bulb indicator

Replaceable ActivePure®

Cell (includes UV Lamp)

Mounting

Plate

RECOMMENDED INSTALLATION TOOLS

PRODUCT CONTENTS

Power Cord

ActivePure® Cell

INSTALLATION HARDWARE

(8) #8 - .75

1/4” Self-tapping screws

Item # US70679

(4) #6 - 32 X 2 inch

Threaded bolts

Item #US70680

(2) Thumb Screws

Item #36-00213

(4) Thumb Nuts

Item #36-00214

(4) #6 - 32

Toggle bolt wall anchors

Item # US70682

You may also need:

Utility Knife Tin Snips

(for metal ductwork)

CAUTION:When the unit is

installed in a roof mounted

HVAC system, the unit must be

protected from the elements.

3 1/2”Hole Saw

for wood or metal

(recommended)

Drill/Power Driver Phillips

Screwdriver

3/8”Drill Bit

(if installing into fiberglass

ducting with toggle bolts)

1/4

1/4”

Nut Driver Bit

Dust Mask

INSTALLATION REQUIREMENTS

Power Connection Requirements:

This device is designed for operation from a standard 24 VAC transformer. Do not connect this unit to any voltage

source above 32 volts. Doing so will cause damage to the unit. The supplied electrical wiring has two terminals for

connection to the G4 unit. For connection to a 24 volt source other than the G4, you will need to remove the two

terminals from the end of the supplied electrical wiring.

NOTE: Unit requires continuous power. Do not install where power to the unit will be cycled on and off.

WARNING! - This unit must be installed by a licensed HVAC

contractor. Failure to do so will void warranty of the product.

1. Unit should be installed after the air handler in the

HVAC system.

2. The ductwork around the installation area should be

clean and dry to ensure proper adhesion of the gasket

materials and any tape used.

3. When installing near a furnace or heating coils, run the heating system through five (5)

full heating cycles to ensure the temperature of the Beyond by Aerus Sanctuairy unit

does not exceed 200˚F.

4. An approximate 3.5” (8.89 cm) opening will need to be cut into the existing

ductwork to install the unit properly.

Air

Handler

Min. 9” x 9”

Metal Ductwork

Min. 10” x 10”

Fiberglass

Ductwork

Max. 15 ft.

METAL DUCTWORK INSTALLATION

1. Locate suitable area

of duct for installation.

3. Mark location for 3.5” opening using either the

mounting plate or included template.

4. Cut hole in duct using 3.5” hole saw.

2. Cut away insulation to expose metal duct (if

needed).

a. Using template, mark 4 Cutting

Method holes on duct.

b. Drill 4 holes where marked.

c. Cut between holes using tin snips.

ALTERNATIVE CUTTING METHOD

5. Remove backing

from mounting plate

adhesive gasket.

6. Center openings and press mounting plate onto

duct. The adhesive gasket will hold the mounting

plate in place.

8. Insert unit into opening. Be sure the air will pass

though the ActivePure® cell honeycomb matrix.

9. Secure the unit to the

mounting plate

with (4) thumb nuts.

7. Secure the mounting plate using (8) #8

self-tapping screws.

METAL DUCTWORK INSTALLATION

CONTINUED

1/4

10. Plug unit into working power receptacle.

Hard wiring unit into HVAC system must

be done by a licensed HVAC installer or

electrical contractor only.

a. Using template, mark 4

holes for alternative cutting

method on duct. If, not already

done,mark 4 corner holes.

b. Draw a line between each alternative

cutting method marks (as shown).

c. Cut between holes using a utility knife.

Continue with #4 (above)

ALTERNATIVE CUTTING METHOD

FIBERGLASS DUCTWORK INSTALLATION

2. Mark location for 3.5” opening using either

the mounting plate or included template.

Also mark the locations of 4 screw holes in

corners (see template).

3. Cut hole in duct using 3.5” hole saw.

4. Drill 4 holes (at corner screw locations) using

a 3/8” drill bit.

1. Locate suitable area

of duct for installation.

This page has been intentionally left blank for the template on the other side.

Beyond by Aerus Sanctuairy  CELL HOLE PLACEMENT TEMPLATE

MARK FOR DUCT INSTALLATION

MARK CENTER FOR 3.5” HOLE SAW

MARK IF USING ALTERNATIVE CUTTING METHOD

MARK FOR DUCT INSTALLATION

MARK CENTER FOR 3.5” HOLE SAW

MARK IF USING ALTERNATIVE CUTTING METHOD

MARK FOR DUCT INSTALLATION

This page has been intentionally left blank for the template on the other side.

Inhaltsverzeichnis

Sprachen:

Andere Aerus Luftreiniger Handbücher

Aerus

Aerus Pet ReFresh Bedienungsanleitung

Aerus

Aerus AQ 1000 Bedienungsanleitung

Aerus

Aerus Pure & Clean Plus A1041A Bedienungsanleitung

Aerus

Aerus LUX GUARDIAN ANGEL Bedienungsanleitung

Aerus

Aerus Air Scrubber Bedienungsanleitung

Aerus

Aerus QuietPure home Bedienungsanleitung

Aerus

Aerus F203C Bedienungsanleitung

Aerus

Aerus QuietPure A1027A Bedienungsanleitung

Aerus

Aerus Lux Guardian Air Air Purifier Bedienungsanleitung

Aerus

Aerus Pure & Clean Bedienungsanleitung

Aerus

Aerus QuietPure A1027A Bedienungsanleitung

Aerus

Aerus Beyond PureCloud Bedienungsanleitung

Aerus

Aerus Eco Sphere Bedienungsanleitung

Aerus

Aerus Mobile Bedienungsanleitung

Aerus

Aerus Air Scrubber Bedienungsanleitung

Aerus

Aerus Air Scrubber Mini EM Bedienungsanleitung

Aerus

Aerus Lux Guardian Air Bedienungsanleitung

Aerus

Aerus Air Scrubber Bedienungsanleitung

Aerus

Aerus Pure & Clean A1040A Bedienungsanleitung

Aerus

Aerus LUX GUARDIAN PLATINUM Bedienungsanleitung

Aerus

Aerus AQ 1000 Bedienungsanleitung

Aerus

Aerus LUX GUARDIAN ANGEL Bedienungsanleitung

Aerus

Aerus Beyond G4 Bedienungsanleitung

Aerus

Aerus Air Scrubber Advanced Bedienungsanleitung

Beliebte Luftreiniger Handbücher anderer Marken

IKEA

IKEA UPPÅTVIND Bedienungsanleitung

Nash

Nash AP-1 PureSmart Bedienungsanleitung

LG PH-U450 Series Bedienungsanleitung

DeLonghi

DeLonghi DDSX 220WFA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Bedienungsanleitung

Sharp

Sharp FU-40SE Bedienungsanleitung

Philips

Philips AC2721 Bedienungsanleitung

TruSens

TruSens Z-2000 Bedienungsanleitung

Motorola

Motorola MBP87SN Bedienungsanleitung

Beko

Beko ATP 7100I Bedienungsanleitung

Carrier

Carrier INFINITY 1620 Bedienungsanleitung

AtmosAir

AtmosAir P2002 Bedienungsanleitung

Winix

Winix NK300 Bedienungsanleitung

Friedrich

Friedrich C-90A Bedienungs- und Montageanleitung

Surgically Clean Air

Surgically Clean Air JADE2.0 Bedienungsanleitung

Base aire

Base aire 555 Pro Bedienungsanleitung

Champion

Champion CP25 Bedienungsanleitung

vollara

vollara Air & Surface Pro+ Bedienungsanleitung