Aerus Beyond LAUNDRY PRO 2.0 Bedienungsanleitung
READ MANUAL CAREFULLY FOR PROPER USE AND OPERATION.
COLD WATER LAUNDRY SYSTEM (EURO)
Made in the USA
2017 Space Technology
Hall of Fame Inductee
2
CONTENTS
General Information . . . . . . . . . . . . . . . . . . . .2
Important Safety instructions . . . . . . . . . . . . . . . 3
Installation Requirements . . . . . . . . . . . . . . . . . 4
Before You Start . . . . . . . . . . . . . . . . . . . . . .5
Removing Cover. . . . . . . . . . . . . . . . . . . . . .5
Installation of Wall Anchors or Screws . . . . . . . . . . . 6
Reinstall the Cover. . . . . . . . . . . . . . . . . . . . .7
Hose Installation . . . . . . . . . . . . . . . . . . . . 7-8
Connecting the Power Adapter . . . . . . . . . . . . . . 8
System Set Up. . . . . . . . . . . . . . . . . . . . . . .9
Changing the ActivePure® Cell Assembly . . . . . . . . . 10
Before Washing Clothes . . . . . . . . . . . . . . . . . 11
Using Your Laundry Pro 2.0 . . . . . . . . . . . . . . . 11
Washers Requiring Hot & Cold Water . . . . . . . . . . . 12
Temp. Control & External Water Tap . . . . . . . . . . . 13
Status Indications . . . . . . . . . . . . . . . . . . . . 13
Frequently Asked Questions . . . . . . . . . . . . . . . 14
Installation Problems . . . . . . . . . . . . . . . . . . 14
Troubleshooting. . . . . . . . . . . . . . . . . . . .15-16
Warranty Information . . . . . . . . . . . . . . . . . . 17
PRODUCT OVERVIEW
Laundry Pro 2.0 is designed to work in conjunction with your washing
machine, using cold water and our proprietary ActivePure®Technology to
clean clothes. As your washer begins to ll, Laundry Pro 2.0 will turn on.
Laundry Pro 2.0 is equipped with an internal leak sensor.
There’s a smart new approach to laundry that’s based on earth-friendly
science and technology. Laundry Pro 2.0, designed and made in America,
eliminates the need for hot water, detergents, fabric softeners and bleaches,
thereby allowing it to pay for itself over and over again.
Laundry Pro 2.0 is easy to install. It is intended to work with residential clothes
washers and is for use by anyone interested in an economical, earth-friendly
alternative to the typical detergents and chemicals currently available,
without modifying existing appliances, electrical systems, or plumbing.
Laundry Pro 2.0 uses a variation of the technology originally developed for
use in the International Space Station and is recognized as a Certied Space
Technology by the Space Foundation.
FILL IN AND SAVE
The location of the serial number is on the back panel of the water unit,
below the water line connection. Write it here and retain for future
reference.
Model No.____________________________________________________________
Serial No. ____________________________________________________________
Date of Purchase ______________________________________________________
Aerus Distributor ______________________________________________________
_____________________________________________________________________
Distributor’s Oce Phone No. ___________________________________________
_____________________________________________________________________
Distributor’s Oce Address _____________________________________________
_____________________________________________________________________
SPECIFICATIONS
AC/DC Adapter:
• AC in: 100 - 240V ~ 50/60 Hz .45A
• DC out: 12V
Power Consumption:
• .4W AC (standby mode)
• 1.3W AC operating
UV Light:
• 185nm
Dynamic Water Pressure:
• Minimum 20 psi to 60 psi / 1.37 ~4.13 bar /
137000 – 413000 Pascal
Water Temperature:
• Use cold water only (do not use hot water)
Operating Environment:
• 50˚F - 100˚F ( 10˚C - 37.8˚C)
• Humidity 40% ~ 85%
Dimensions:
• 17.3” x 5.19” x 3.69”
• 43.94cm x 13.48cm x 9.37cm
Weight:
• 4.3 lbs
• 1.95 kg
GENERAL INFORMATION
3
Read this manual in its entirety prior to installing or using your Laundry Pro 2.0.
• For indoor use only
• Do not operate unit with cover removed
• Disconnect all power before servicing
• Do not use an extension cord or other adapter with this appliance
• Only use the Power Supply that comes with this device. DO NOT USE any other Power Supply
• This appliance is not recommended for use with high sediment content water; if your water has a
high sediment content, consult a water ltration expert for available options
• Maximum dynamic water inlet pressure is 60 psi
• Use the new hose included with the unit, when connecting the Laundry Pro 2.0 to your washing
machine; you should also replace any washing machine hose that is more than
3 years old
• Do not clean the cover of your Laundry Pro 2.0 with harsh chemicals, abrasives, or cleansers; to
clean, use a soft cloth dampened with water
• Laundry Pro 2.0 is designed for normal residential use only; use in a commercial or
non-residential setting may damage the unit and will void your warranty
• Children should be supervised around this device
• This device cannot be used by children or people with physical disabilities, sensory or mental
impairment, or with the lack of knowledge, unless they are supervised or have been instructed to
use the device by the person responsible for their safety
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY PRECAUTIONS
• To prevent unnecessary risk of re, electrical shock, or personal injury, all wiring must be done in
accordance with the National Electrical Code ANSI/FNPA, No. 70 - Latest Revision and local codes
and ordinances in the USA. For Electrical Codes outside the USA, consult your local regulatory
agency for the latest codes and ordinances. It is the personal responsibility and obligation of the
appliance owner to provide adequate electrical service for this appliance.
We have provided important safety
warnings in this manual
and on your appliance. Always read
and obey all safety messages.
Safety warnings in this manual
are dened as follows:
WARNING:
Electrical shock hazard.
You can be killed or seriously
injured if you don’t follow
instructions.
CAUTION:
Damage to your appliance or the
surrounding area can occur if
you don’t follow instructions.
DANGER:
Death or serious injury can occur
if instructions are not followed
immediately.
NOTE:
This information is included to
aid in installation and use of this
appliance.
NOTE: Your Laundry Pro 2.0 Unit was factory tested. It is normal for some residual
water to still remain in the unit as a result of these tests.
Water treated by your Laundry Pro 2.0 unit is intended for clothes washing only and is NOT
approved for any internal consumption such as drinking, bathing, brushing teeth, etc. DO NOT
drink, ingest, or internally consume the water from your Laundry Pro 2.0 unit or washing machine.
DO NOT provide water from your Laundry Pro 2.0 to your pets or other animals.
CAUTION:
SAVE THESE INSTRUCTIONS
4
WATER
OUTLET
WATER
INLET
INSTALLATION REQUIREMENTS
17.3”(43.94 cm)
5.19”(13.48 cm)
3.69”(9.37 cm)
Incoming water pressure must be greater than 20 psi / 1.37 bar (137000
Pascal). If your household water pressure is greater than 60 psi / 4.13
bar (413000 Pascal), you must install an in-line pressure reducer before
installing Laundry Pro 2.0. Failure to follow these instructions may result
in water leakage, property damage, personal injury, and may void your
warranty. Water pressure of 20 psi / 1.37 bar (137000 Pascal) to 60 psi /
4.13 bar (413000 Pascal) is required to correctly operate your Laundry
Pro 2.0. Low water pressure may prevent your unit from operating
properly and/or cause a failure in your washing machine’s water valve.
The washer’s water valve may also not shut o completely. Check
the documentation supplied with your washing machine for exact
specications. Your washing machine and cold water faucet must be
within 4 feet of the right side of the unit to use the inlet hose provided
with your Laundry Pro 2.0.
TO AVOID THE POSSIBILITY OF WATER DAMAGE, SHOULD A HOSE
LEAK, ALWAYS HAVE FAUCETS ACCESSIBLE AND TURN OFF
FAUCETS WHEN WASHER IS NOT IN USE. DO NOT USE WITH A
CARBON FILTER.
CAUTION:
ELECTRICAL REQUIREMENTS
100 - 240 Volt 50/60 Hz 5 AMP (minimum) Fuse or Circuit Breaker.
Laundry Pro 2.0 is equipped with an AC to DC power supply.
LOCATION CONSIDERATIONS
The Laundry Pro 2.0 must never be installed in areas where water
may freeze since the unit will always maintain some water in the unit,
the water valve, and hose areas. This can cause damage to internal
components. It is also recommended to avoid installation in areas of
high humidity, as it can eect the operation of the unit.
WATER REQUIREMENTS
A dynamic water pressure of greater than 20 psi / 1.37 bar
(137000 Pascal) and less than 60 psi / 4.13 bar (413000 Pascal) is
required to correctly operate your Laundry Pro 2.0.
See Cautions below.
NEVER USE AN EXTENSION CORD
CAUTION:
5
BEFORE YOU START
REMOVING COVER
• Remove your new Laundry Pro 2.0 from its packaging
• Inspect the unit for any signs of shipping damage
NOTE: Your Laundry Pro 2.0 unit was factory tested. It is normal for some residual water to still remain in the unit as a result of these tests.
Screws
1. Remove the two (2) cover screws located on
the bottom of the unit.
2. Remove the two (2) screws (not shown) along
the top of the Laundry Pro 2.0.
3. To remove the cover, pull the top away from the
unit, then lift o the cover.
6
INSTALLATION OF WALL ANCHORS OR SCREWS
A. If using supplied wall anchors, drill two 3/16” (4.76 mm) diameter holes.
Place two wall anchors into the wall. Install two supplied screws and tighten
until almost all the way in.
B. If mounting to wall studs, drill two 3/32” (2.381 mm) diameter holes
approximately 1” (25.4 mm) deep. Install two supplied screws and tighten
until almost all the way in.
17.3”(43.94 cm)
Keyholes
NOTE: Washing machine and cold water faucet must
be within 4 feet (1.21 m) of the right side of unit.
1. Place the Laundry Pro 2.0 to the wall and mark the appropriate keyholes
with a pencil.
Screws (not shown)
2. Position the keyholes of the Laundry Pro 2.0 onto the screws (not
shown). Finish tightening screws enough to securely mount unit, but
still allowing it to be removed from wall. Remove unit from wall.
NOTE: The provided hardware kit contains adhesive backed rubber spacers
to be placed on back of unit to provide additional clearance from
wall if needed for hose installation or the use
of ActiveClean Port. (Page 12)
7
1. Turn the cold water o by shutting o the cold water faucet.
NOTE: To help prevent water spray when disconnecting hoses, you can relieve
pressure in the water line by momentarily starting your washing machine.
NOTE: To ease hose installation and prevent cross threading, connect hose
prior to mounting unit on wall.
NOTE: Remove the two black caps from the hose connections
before installing hoses.
2. Remove the cold water hose from the cold water inlet on the back of
your washing machine. Leave hot water hose attached.
When connecting hoses to your Laundry Pro 2.0 start by hand tightening the hose
connector(s). Using adjustable pliers, nish tightening hose connector(s). Do not
remove or disconnect the hot water line from your washing machine or water valve.
CAUTION:
1. Return the Laundry Pro 2.0 cover to its original position, tting the bottom in
place and tipping upward.
2. Secure with two (2) screws (not shown) along the top edge.
3. Put the two (2) remaining screws along the bottom edge and tighten.
REINSTALL THE COVER
HOSE INSTALLATION
Screws
Screws
8
CONNECTING POWER ADAPTER
1. Insert the provided power cord into the POWER IN socket located on the side of the unit.
Do not use any AC/DC adapter other than the one supplied with your Laundry Pro 2.0 or Aerus replacement AC/DC adapter
(item#: 49874-EURO/49873-US). Failure to follow these instructions may void your warranty and/or result in damage to your
unit, re, or electrical shock.
CAUTION:
HOSE INSTALLATION CONTINUED
3. Connect the hose from the cold water inlet on your washing
machine to the INLET connection on your Laundry Pro 2.0.
5. Finally, connect the new hose to the cold water inlet on your washing machine.
4. Connect the new hose provided with your Laundry Pro 2.0 to the water
OUTLET connector on your Laundry Pro 2.0 unit.
NOTE: To ease hose installation and prevent cross threading,
connect hoses prior to mounting unit on wall.
NOTE: If your existing hose is more than 3 years old, we recommend that you replace
it with the optional stainless steel hose (item#: 49738-EURO/49701-US).
NOTE: Do not plug the adapter into the wall socket until installation is complete. See page 9.
9
SYSTEM SET UP
4. Start your washer. The status light should
illuminate blue after a few seconds.
NOTE: Your Laundry Pro 2.0 will automatically turn
on and o as your washing machine starts, and stops.
Electrical Shock Hazard. When working with electrical connections, the appliance
and surrounding area should be clean and dry of any standing water. Failure to
follow these instructions can result in death, re, or electrical shock.
Electrical Shock Hazard. Do no use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
WARNING: WARNING:
1. Plug power cord into the wall outlet of your
home’s electrical power system. See page 4 for
electrical requirements.
Status Indicator Lights
2. Turn on the cold water valve.
3. Check all hoses to ensure no water
is leaking. Tighten if necessary.
10 Screws
CHANGING THE ACTIVEPURE CELL ASSEMBLY (S/N 49883)
1. Unplug from power source and remove mounted
unit from wall.
2. Remove cover (See Page 5).
3. Unplug photo sensor lead (Figure 1).
4. Remove tubing from cell (Figure 2).
5. Unplug wiring harness from bulb (Figure 3).
6. Remove two screws to remove cell (Figure 4).
7. Replace with new cell (S/N 49883)
and remount to base.
8. Plug wiring harness back onto bulb.
9. Fit tubing back onto cell.
10. Re-plug photosensor lead.
11. Replace cover (See page 7).
Photo Sensor Lead
Cell Tube
Wiring Harness
Figure 1
Figure 2
Figure 3
Figure 4
NOTE: The ActivePure Cell Assembly requires replacement at approx. 9,000 hours of use. The LED will ash periodically (visual chirp) to notify that cell
replacement is required. The UV bulb will NOT be turned on again until the cell has been replaced.
Andere Handbücher für Beyond LAUNDRY PRO 2.0
1
Inhaltsverzeichnis
