AES StylusAB Bedienungsanleitung

P a g e | 1

Installation & User Manual

For

Styluscom

Wired Video Intercom System

Models StylusAB, StylusABK, StylusAS

Manual Version 1

P a g e | 2

Contents

Overview of system

…………….Pg 3

Site Survey

…………….Pg 3

SIM card

…………….Pg 3

Power

…………….Pg 3

Installation

…………….Pg 4

Architectural panels

…………….Pg 4

Hooded Panels

…………….Pg 4

Flush Panels

…………….Pg 4

Installing the SIM card

…………….Pg 5

Connections on GSM controller

…………….Pg 5

Codelock Keypad connections

…………….Pg 6

Wiring Tips

…………….Pg 6

Output connections example

…………….Pg 7

Alternative Keypad Wiring

…………….Pg 7

Powering up

…………….Pg 8

Programming

…………….Pg 8

Complete list of Parameters

…………….Pg 11

Keypad Overview

…………….Pg 12

Basic Keypad Programming

…………….Pg 13

Full Keypad Programming

…………….Pg 13

Using the Keypad

…………….Pg 15

Using the Intercom

…………….Pg 15

Control by SMS

…………….Pg 15

Check if Door/Gate Opened/Closed

…………….Pg 16

Using the Optional App

…………….Pg 16

Maintenance of Intercom

…………….Pg 17

Troubleshooting Guide

…………….Pg 17

P a g e | 3

Overview of System

Please read this entire manual before attempting to install this system.

This system should only be installed by a professional automatic gate installer or access control

specialist dealer.

It is recommended that the system be set up, configured, commissioned and tested on a

workshop bench before taken to site for installation.

Site Survey

If cable has been pre-installed, make sure that the cable type and length is within the guidelines

shown below….

Signal quality will be better with shielded CAT5, and when routed away from power cables.

Power

TIP: Most technical calls received are due to installers using CAT5 or alarm cable to power

the unit. Neither are rated to carry enough power over longer distances. Please use

following cable…

Up to 2 metres (6 feet) –Use minimum 0.5mm2(18 gauge)

Up to 4 metres (12 feet) –Use minimum 0.75mm2(16 gauge)

Up to 8 metres (24 feet) –Use minimum 1.0mm2(14 gauge)

Using insufficient power cable thickness will cause excessive stress on electronic components,

and therefore void the manufacturer’s warranty.

15v Power

adaptor

15v

Power

adaptor

To avoid such problems, it is recommended (and is good practice) to locate power supplies as

close to the devices as possible.

P a g e | 4

Monitor Mounting

Door Station Mounting

Mount the intercom at the desired height for pedestrian or car users. The camera angle

is wide at 110 degrees to cover most scenarios.

Loosen top 2 screws only

Hingefrontdoor

SideView

Tip: Do not drill holes in the wall with the intercom in positon, otherwise dust may get

around the camera window and impair the camera view.

2. Plug monitor into ribbon cable only

once all wiring is complete.

1. Mount monitor mounting

assembly to wall.

P a g e | 5

Door Station & Monitor Wiring

P a g e | 6

Wiring Tips for Locks and Gates

Note: The manufacturer can only support the use, operation and functionality of the

intercom and keypad themselves. Professional wiring to door release or automatic gate

systems is the responsibility of the installer. Please consult a security integrator for

further support.

Basic Keypad Programming

For most installs, it is sufficient to simply enter a single user code as follows..

0 0 0 0 * *

Quick start guide

1) Enter programming mode (amber LED should be ON)

1 0 2 0 0 ? ?? ? #0

2) Enter a new user code...

* *

3) Exit programming mode

4) Enter the new user code to check the relay clicks.

Tip: The engineer code must be the same length as user codes. So if using a 6 digit

engineer code, then user codes must also be 6 digits long etc.

P a g e | 7

Full Keypad Programming

Enter programming mode..

0 0 0 0 * *

Exit programming mode..

* *

Enter a new ENGINEERS code…

Go into programming mode firstly then enter the following sequence…

Location

0 1 ?? ? ?

4-8 digit code Validate

Enter or delete new user codes

There are 3 groups of user codes. Group 10 for relay 1, group 20 for relay 2, and group 30 for

relay 3. The programming sequence is shown below…

Memory locations

000-999 for relay 1

001-100 for relay 2

001-100 for relay 3

1 0 2 0 0

10= relay 1 codes

(1000 available)

20= relay 2 codes

(100 available)

30= relay 3 codes

(100 available)

? ?? ? #0

2= add code

5= delete code Pin code 4-8 digits Validate

Example: Add user 31 to have access code 5555 operating relay 2….

2 0 2 0 3 5 55 5 #1

Group 2 Add code Location 31 Pin code 5555 Validate

Programming relay output times and modes…

? ? 01 -

0 = start / stop toggle mode (latching)

1-99999 = seconds momentary operation

99999

or #

51=relay1

52=relay2

53=relay3

Validate

Delete a user code even if you don’t know the code…

? ? 5 ? ?? #

10=relay1

20=relay2

30=relay3 Delete code ID location to be deleted Validate

The unit is now in programming mode. Amber LED on the

keypad should remain permanently on. 0000 is the default

programming passcode.

The unit should exit programming mode and the amber LED

should start flashing again.

Replace ???? with your new ENGINEERS

code.

P a g e | 8

Delete an entire group of codes

? ? 0 9 99 #

10=relay1 group

20=relay2 group

30=relay3 group Super delete code Validate

Programming super user codes…

A super user code can activate any of the 3 relays

Location

0 2 ?? ? ?

4-8 digit code Validate

Restoring defaults

When in programming mode, you can enter the following sequence…

9 9 99 #

When the master code is forgotten….

1) Wire a push button (or replicate with wire link) across the Egress terminal and (-)GND.

2) Switch off power for 1 minute.

3) Switch ON power.

4) During the first 60 seconds, press the EG button once to enable the function.

5) Enter the following code..

8 0 08 * *

The keypad should now be in programming mode, ready to accept new data.

Using the keypad

Using the standard codes…

Once you have exited out of programming mode, simply enter the user code.

Using super user codes

?? ? ? # 1 Activate output 1

?? ? ? # 2 Activate output 2

?? ? ? # 3 Activate output 3

P a g e | 9

Sound and Volumes

With intercoms operating as a loud speaker and the monitor also acting as a loud speaker, it is

important to set up the speech volumes carefully.

1. Reduce the mic and speaker volumes to minimum levels on the door station and set the indoor

monitor volume at approximately 25%.

2. Keeping the microphone volume at minimum, slowly increase the speaker volume on the door

station to a level which is acceptable. Do not increase the speaker volume more than is

necessary, otherwise feedback or clipping will occur.

3. Adjust the monitor speaker volume as necessary, again keeping it as low as possible.

TIP: Adjusting the microphone sensitivity on the door station is not recommended. For most

installs it is best to keep it at the absolute minimum level.

Monitor Power Scheme

Tip: Check distance between monitors before installing wiring. For pre-installed wires, check that

the cable type and distance complies with one of the two wiring plans below…

MICROPHONE

Keep at complete

minimum if possible.

SPEAKER

Increase if necessary

(keep as low as possible)

DOOR STATION

P a g e | 10

Additional Monitor Wiring

Tip: Up to 4 monitors in total (1 master + 3 slaves) can be used together, depending on cable

used and distance between monitors and distance to the door/gate station.

Tip: See next page on how to set MASTER and SLAVE monitor modes.

Dieses Handbuch passt für folgende Modelle

Andere AES Gegensprechanlage Handbücher

AES

AES MultiCom 500 Bedienungsanleitung

AES

AES SnapCOM Prime 4G Bedienungsanleitung

AES

AES Prime 6 Series Bedienungsanleitung

AES

AES GSM-3AB Bedienungsanleitung

AES

AES 603AB Bedienungsanleitung

AES

AES 605 Bedienungsanleitung

AES

AES 603AB Bedienungsanleitung

AES

AES Cellcom Prime6 Bedienungsanleitung

AES

AES CellCOM Plus AB Bedienungsanleitung

AES

AES Cellcom Prime 5AB Bedienungsanleitung

AES

AES MultiCom 500 Bedienungsanleitung

AES

AES 605A Bedienungsanleitung

AES

AES CellCOM Lite 4G Bedienungsanleitung

AES

AES Prime 6E Bedienungsanleitung

AES

AES AB Bedienungsanleitung

AES

AES 603 DECT Bedienungsanleitung

AES

AES 602AB Bedienungsanleitung

AES

AES GSM-800/AB Bedienungsanleitung

AES

AES 702/AB Bedienungsanleitung

AES

AES WiFi Predator Bedienungsanleitung

AES

AES MultiCOM Lite 4G Bedienungsanleitung

AES

AES MultiCom 100 Bedienungsanleitung

AES

AES WiFi Predator Bedienungsanleitung

AES

AES 603 SPARTAN Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung