AFi MT-1 Bedienungsanleitung
© Copyright 2005, American Fibertek, Inc. 0520JD
Instruction Manual
MT-1
Mini Video Transmitter
2
INSTALLATION AND OPERATION INSTRUCTIONS
INTRODUCTION
Thank you for purchasing your American Fibertek MT-1 multimode mini video
transmitter. Please take a few minutes to read these installation instructions in order to
obtain the maximum performance from this product.
FUNCTIONAL DESCRIPTION
The MT-1 operates as half of a transmitter / receiver pair for the transmission of
baseband NTSC, PAL, RS170, or RS343 video signals over a single multimode fiber
optic cable. It is designed to operate with the MR-10, MR-10M, RR-10, RR-10M, RR-20,
or RR-20M video receiver. The RR-20 contains the electronics and optics of two RR-10
units mounted on one printed circuit board to save space and reduce cost. The RR-20M
contains the electronics and optics of two RR-10M units mounted on one printed circuit
board.
The MT-1 converts a single video input into a single AM modulated optical output using
an 850 nm wavelength source. The 1, 10, and 20 Series product is designed to operate
over an optical loss budget range of 0 to 17 dB. The MT-1 operates on 50 um or 62.5
um multimode fiber. Refer to the data sheets for detailed performance specifications.
The small size and light weight of the MT-1 allows for direct mounting on the back of a
camera in an enclosure. For a wall mounted version please see the MT-10. For a rack
mounted version please see the RT-10 or RT-20.
3
INSTALLATION
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND
SHOULD CONFORM TO THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 AND
LOCAL CODES.
Mount the unit directly to the output of a video source. Be sure to allow sufficient room
for the required minimum bend radius of the fiber cable used.
POWER SOURCE
THIS PRODUCT SHALL BE POWERED BY A LISTED CLASS 2 POWER SUPPLY
ONLY.
This unit requires a +12VDC power source for proper operation. Current draw is
approximately 50mA maximum. In the USA and in Canada an American Fibertek PS-12
is supplied with this unit. The negative side of the power input is directly connected to
ground. ANSI/NFPA 70 Class 2 wiring is recommended.
POWER CONNECTION
Power is supplied to the unit via a two wire copper cable. The red wire is connected to
+12 volt dc and the black wire is connected to ground.
FIBER CONNECTION
The fiber optic connection is made via a ST connector located on the side of the unit.
VIDEO INPUT CONNECTION
The video input connection is made via a BNC connector on the side of the unit. The
video input should be directly connected to an appropriate 75Ωbaseband video source
such as the output of a camera.
4
LIFETIME WARRANTY INFORMATION
American Fibertek, Inc warrants that at the time of delivery the products delivered will be
free of defects in materials and workmanship. Defective products will be repaired or
replaced at the exclusive option of American Fibertek. A Return Material Authorization
(RMA) number is required to send the products back in case of return. All returns must
be shipped prepaid. This warranty is void if the products have been tampered with. This
warranty shall be construed in accordance with New Jersey law and the courts of New
Jersey shall have exclusive jurisdiction over this contract. EXCEPT FOR THE
FOREGOING WARRANTY, THERE IS NO WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, EXPRESSED OR
IMPLIED, WHICH EXTENDS BEYOND THE WARRANTY SET FORTH IN THIS
AGREEMENT. In any event, American Fibertek will not be responsible or liable for
contingent, consequential, or incidental damages. No agreement or understanding,
expressed or implied, except as set forth in this warranty, will be binding upon American
Fibertek unless in writing, signed by a duly authorized officer of American Fibertek.
SERVICE INFORMATION
There are no user serviceable parts inside the unit.
In the event that service is required to this unit, please direct all inquiries to:
American Fibertek, Inc. Phone: (877) 234-7200
120 Belmont Drive Phone: (732) 302-0660
Somerset, NJ 08873 FAX (732) 302-0667
E-mail: techinfo@americanfibertek.com
Inhaltsverzeichnis
Andere AFi Sender Handbücher
AFi
AFi MT-388SL Bedienungsanleitung
AFi
AFi RT-404C Bedienungsanleitung
AFi
AFi MT-404 Bedienungsanleitung
AFi
AFi MT-91P589C-SL Bedienungsanleitung
AFi
AFi 48 Series Bedienungsanleitung
AFi
AFi RT-980C Bedienungsanleitung
AFi
AFi MT-3340-12VDC Bedienungsanleitung
AFi
AFi MT-980C-SL Bedienungsanleitung
AFi
AFi MT-740C Bedienungsanleitung
AFi
AFi MT-780C-SL Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
