AFL FlexScan TS100 Bedienungsanleitung

FlexScan®TS100

Optical Troubleshooter

Quick Reference Guide

Test & Inspection

www.AFLglobal.com

Controls, Display, Interfaces

Battery Charging

•Plug the included AC charger into AC outlet.

•Connect charger plug to the Power port.

•AC/Charger indicator will illuminate to indicate charging status as follows:

–RED - Charging battery

–GREEN - Fully charged

–OFF - AC disconnected

–Flashing RED/GREEN = Battery charging halted due to over-temperature.

•FlexScan charges while operating.

•A fully-charged battery operates for approximately 12 hours of typical use.

Understanding Battery Charge Status

When FlexScan is ON, battery icon shown on the display indicates battery status as follows:

- Battery fully charged

- Battery partially charged

- Battery nearing empty

- Battery discharged

- Battery charging

Battery fully charged, Battery partially charged, and Battery discharged symbols will only be

shown when unit is operating without being connected to AC.

Conguring FlexScan to Auto-Off

•Turn your FlexScan On.

•From the displayed Home screen, press Home/Menu button to display General Settings

menu.

•In the Settings menu, locate the Auto Off Timer option.

•Touch the Auto Off Timer eld to display the settings sub-menu.

•Select the desired power save option (Never, 5 min, 15 min).

1. Power button

2. Power jack (5 VDC)

3. Charge/AC indicator

4. USB host port

5. Micro-USB function port

6. 1650 nm OTS/OLS/OPM Port

7. VFL port

8. Touchscreen display

9. Home/Menu button

10. Test Start/Stop button

11. VFL button

2 5

467

New Test - FlexScan’s Home Screen

The New Test screen is the FlexScan’s main screen that is displayed at startup.

From the New Test screen you may perform the following setup and operations:

1. Press Home/Menu button to display the Test/Home Menu screen and select Save, Send, or congure General Settings.

2. Press Start/Stop button to enable Live Fiber check, or to start a new test, or (if test is running) to end a test.

3. Press VFL button to enable VFL mode.

4. Touch Tool icon to congure Test Settings or select OLS/OPM or Inspection.

5. Touch Launch Cable to change LC length.

6. Touch Network to congure Network Type: Pt-to-Pt or FTTH PON and expected split ratio.

Test/Home Menu Screen Overview

1. Test/Home Menu screen may be accessed from the Test Results/Home screen by

pressing the Home/Menu button, or from the LinkMap screen by touching the

3-bar Menu icon.

While in Test Home Menu screen, you may perform the following operations:

2. Touch Save As to name and save results.

3. Touch Send To option to send results to Bluetooth-paired device.

–If Send To option is grayed out, Bluetooth is either not available or disabled.

Select General Settings to enable Bluetooth and pair to mobile device running

the FlexScan App if you wish to upload results to that device for reporting or

sharing.

4. Touch General Settings to select, view, and edit General Settings.

5. Touch My Projects to recall and view saved results.

6. Touch USB icon to enter USB upload/download mode.

7. Touch Info icon to display Info screen.

8. Touch Back to return to Test/Home.

Fault Locate Setup Screen Overview

1. Fault Locate Setup screen is accessed from the Test screen by touching the TS100 Tool icon.

2. When in Fault Locate Setup screen, select a Test Setting to edit it

–Network Type

–Launch Cord

–Pass/Fail Rules

–Fiber Type

3. Press Start/Stop to initiate a test and return to Home screen.

4. Press Home/Menu or touch Back to return to Home/Test Results screen without starting a new test.

5. Touch dB/dBm icon to select Light Source & Power Meter test screen.

6. Touch Inspection icon to select Connector Inspection display screen.

FleXpress®Fault Locate Test Setup

Network Type

Touch Network Type to view/edit the network type:

•FTTH PON through Splitter (Note: FTTH PON through Splitter is only available in TS100-70!)

–Touch current Splitter 1 Split Ratio to change it

•Point-to-Point/ PON to Splitter

•Touch Back to return to Test Setup

Launch Cord

Touching Launch Cord option displays the Launch Cord Setup screen that allows

the user to View / Edit Launch Cable Length:

1. Touch Clear to clear current launch cable length

2. Enter desired launch cable length

3. Touch Cancel or Back to return to previous screen without saving changes

4. Touch Done to save changes and return to previous setup screen 1

Pass/Fail Rule

•Touch Pass/Fail Rule option to select ITU G.671, TIA-568.3-D, or User pass/fail rules.

•Touch and hold selected Pass/Fail rule to view/edit link and event pass/fail limits.

•Use left/right arrows to navigate through, view and edit pass/fail limits.

Notes:

1. Splice, Connector and Splitter pass/fail limits are xed and cannot be edited for ITU G.671 and TIA-568.3-D standards.

2. Splitter pass/fail limits can only be viewed and set in TS100-70.

Fiber Type

Fiber Type settings depends on the selected Network Type option. Touch the Fiber Type eld to display one of the following:

•Single-mode G.65x or User-SMF options

Viewing and Conguring Fiber Type

G.65x Fiber Settings may be viewed but NOT changed.

User Settings may be viewed and changed.

To view and edit User Fiber Type Settings

•While in the Setup screen, make sure the User Fiber Type label is displayed in the Fiber Type eld.

•If not, touch the Fiber Type eld to display the Fiber Type menu and touch the User option to select.

•When back in the Setup screen, touch and hold the displayed User label to open the User Fiber Type settings screen and congure settings as

follows:

–Group Index of Refraction (GIR)

–Backscatter Coefcient (BC)

–Fiber Attenuation (ACI; Loss-per-Distance)

•Touch the desired parameter eld (e.g. GIR @1310 nm) to display its Editor screen.

•Edit the value using on-screen controls. Touch Done to save changes and return to the User Fiber Type settings screen.

•Touch Back to return to the Setup screen.

While in the General Settings screen, select and view or edit settings as follows:

•Language: Select user interface language

•Date and Time: Congure local date and time

•Distance Units: Select m, km, ft, kft or mi

•Bluetooth: Enable/disable Bluetooth and pair to another Bluetooth device

–Enable Bluetooth, touch the on/off control

–Select Search to discover devices, then select device from list to pair

•Speaker Volume: Adjust speaker volume

•Screen Brightness: Adjust display brightness and auto-dimming for power savings

•Auto Off Timer: Enable/disable auto-off and congure auto-off delay

•Launch Quality Check: Enable/disable launch quality check

•Remote Control: (Future)

•Received Image: Display received inspection image in popup window, or save in tray for later viewing

•Switch Mode: Congure multi-ber testing when connected to MFS multi-ber switch

General Settings

General Settings screen is accessed from the Test Results Screen, by pressing Home/Menu button and then selecting General Settings.

While in the General Settings screen:

•Touch the desired setting eld (e.g. Language) to display a sub-menu.

•Touch Left / Right Arrows to display additional General Settings screen.

•Touch Back to return to the previous menu.

Live PON Test

Test Sequence in Live PON Test

•Press Start/Stop to check Live Fiber and allow the user to congure test setup

–Live Power levels measured and optionally compared against pass/fail limits

–Touch TS100 Tool icon to congure Test Settings or select OLS/OPM or Inspection

–Touch Launch Cable Length to edit LC length

–Touch Network Conguration to edit Network Type: Pt-to-Pt or FTTH PON and Split Ratio

–Press Start/Stop again to initiate a test

•Touching [Press To Start] will also initiate a test

–Press Start/Stop to end a test

–Link Length, Loss, ORL detected and measured in 3-5 seconds

–Test continues to locate, identify and measure events

–Test completes within 30 seconds, identifying faults with loss or reectance exceeding maximum allowed levels

•Touch LinkMap to view LinkMap for most recent test

•Press Home/Menu to select Save/Send or General Settings

Inhaltsverzeichnis

Andere AFL Werkzeuge Handbücher

AFL

AFL HIBUS HCS Series Referenzhandbuch

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung