Agilent Technologies 5DX Technische Daten
Agilent Technologies
Medalist 5DX Automated
X-ray Inspection System
Operator Instructions
Operator Instructions 3
Contents
1Emergency Stop 5
2Hardware Overview 6
Medalist 5DX Diagram 6
System Light Tower 7
Operator Control Panel 8
3Operator Instructions 9
Startup the System 9
Verify the Safety Interlocks are Closed 9
Verify the X-Ray Has Been Enabled 9
Log on to Microsoft Windows XP 9
Log on to the Medalist 5DX User Interface 9
Run Testing 11
End Testing 13
Log Off Microsoft Windows 13
4What to do in Case of a Problem 14
Panel Retrieval 14
Other Errors 15
4 Operator Instructions
Emergency Stop
Operator Instructions 5
1 Emergency Stop
CAUTION
The emergency stop buttons are intended for use in emergency situations only
and should not be used for normal system shut down. Repeated misuse of the
emergency stop buttons will eventually cause damage to certain components or
the loss of data or both.
An emergency stop button is used to quickly shut down power to the
Medalist 5DX. The Medalist 5DX is equipped with two emergency
stop buttons located on either side of the Medalist 5DX main cabinet,
centered above the outer barrier panels. Whenever one of the
emergency stop buttons is pressed, all power is immediately removed
from the Medalist 5DX subsystems, with the exception of the system
controller and the monitor. Call a service technician to restart the
system after an emergency button has been pressed.
Push down on one of the emergency stop
buttons in an emergency situation.
The emergency stop button locks
OFF when pushed.
6 Operator Instructions
2 Hardware Overview
Medalist 5DX Diagram
The Medalist 5DX Automated X-ray Inspection System provides a
comprehensive test and inspection process to discover solder defects
on a circuit board.
Figure 1 Medalist 5DX system
1System controller
2Emergency stop (EMO) button
3Panel handler access door
4Connector for anti-static wrist strap
5System light tower
6Monitor
7Operator control panel
8Keyboard and mouse tray
9Power distribution unit
2
6
7
1
3
5
4
9
2
3
8
Hardware Overview
Operator Instructions 7
System Light Tower
The system light tower is permanently attached to the electronics
cabinet. The system light tower is used to visually indicate the
operating condition of the Medalist 5DX.
Figure 2 System light tower
1Buzzer —If enabled, sounds when there is a hardware failure.
2Red Lamp —System has a hardware failure and requires
attention.
3Yellow Lamp —System is waiting for user input.
4Green Lamp —System is operating.
1
2
3
4
8 Operator Instructions
Operator Control Panel
The operator control panel provides an X-ray Control key and X-ray
control buttons as well as status LEDs (see Figure 3). It is attached
to the keyboard tray.
Figure 3 Operator control panel
1X-ray Control key (Enable (1)/ Disable (0))
2X-ray Control enable button
3X-ray Control disable button
4X-rays LED
5Safety Interlocks LED
1
2
3
4
5
Operator Instructions
Operator Instructions 9
3 Operator Instructions
Startup the System
The Medalist 5DX is operated through the use of a user interface
running on the system controller. Before starting the system
software, verify that the X-ray has been enabled.
Verify the Safety Interlocks are Closed
On the operator control panel (see Figure 3) verify that the Safety
Interlocks green LED is lit. If it is not, call a service technician to
resolve the problem.
Verify the X-Ray Has Been Enabled
On the operator control panel (see Figure 3) verify that the X-ray
Control key is in the enabled position (1) and press the X-ray Control
enable button (1). Verify that the X-rays red LED is lit.
Log on to Microsoft Windows XP
Log on to Microsoft Windows using the Windows user name and
password provided by your administrator. When you log on, the
Medalist 5DX software starts automatically.
Log on to the Medalist 5DX User Interface
Log on to the Medalist 5DX user interface using the user name
provided by your administrator. Press the ‘Enter’ key to Login.
Figure 4 Login
10 Operator Instructions
The system will perform a system startup. This may take a few
minutes (see Figure 5).
Figure 5 Startup progress
Andere Handbücher für 5DX
2
Inhaltsverzeichnis
Andere Agilent Technologies Diagnosegeräte Handbücher
