Agilent Technologies E4400-60230 g Kurzanleitung

Firmware Upgrade Guide

Part Number E4400-90549

Printed in USA July 2012

Supersedes May 2005

Agilent Technologies Firmware Upgrade Kits

E4400-60230 and E4400-60597

for ESG/PSG Signal Generators

Notice

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable

for errors contained herein or for incidental or consequential damages in connection with the furnishing,

performance, or use of this material.

Microsoft®, Windows®, Windows NT®are U.S. registered trademarks of Microsoft Corporation.

NI-488.2 is a trademark of National Instruments Corporation.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal

Generators

Introduction

The instructions in this firmware upgrade guide enable you to install the PSG/ESG Upgrade Assistant 5.12 on your

computer from either the Agilent Technologies website or a CD-ROM and upgrade firmware on ESG-B signal generators

with <B.03.20.

NOTE For Agilent E44xxB ESG Signal Generators Models Only

When upgrading Agilent E44xxB ESG signal generators from firmware versions <B.03.20, see, “ESG-B

Firmware Installation For Versions <B.03.20” on page 14.

To upgrade firmware on PSG/ESG signal generators, perform the following procedures:

1. Check signal generator functionality on page 5.

2. Confirm required equipment on page 6.

3. Connect an RS-232, GPIB, or LAN interface to a PC on page 8.

4. Install PSG/ESG Upgrade Assistant 5.12 and firmware files on page 11.

5. Use the PSG/ESG Upgrade Assistant 5.12 with firmware files on page 12.

6. Check signal generator functionality on page 5.

Product Affected: . . . . . . . . . . . . . . . . . . . . . . . . . All

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . All

Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All except Option H98

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Technologies Service Center

(X) Personnel Qualified by Agilent Technologies

(X) Customer

Estimated Installation Time: . . . . . . . . . . . . . . . 75 minutes (RS-232), 30 Minutes (GPIB), 3 minutes

(LAN)

Estimated Verification Time: . . . . . . . . . . . . . . . 1 minute

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Overview of Upgrade Assistant 5.12

PSG/ESG Upgrade Assistant 5.12 is used for upgrading firmware on PSG/ESG signal generators:

• it is a Windows-based program

• it replaces PSG/ESG Upgrade Assistant 5.00 through 5.11

as well as ESG Upgrade Assistant 2.12, 2.22, and 3.3.

• it allows new and previous versions of firmware installations to be performed using either:

— RS-232 or GPIB on Agilent E44xxB ESG Signal Generators

— GPIB or LAN on Agilent E44x8C ESG Signal Generators

— GPIB or LAN on Agilent E824xA/5xA PSG Signal Generators

— GPIB or LAN on Agilent E82x7C/D PSG Signal Generators

• it has an associated HTML page that describes the following information for each firmware upgrade version:

— information about new features and enhancements

— a list of improvements and defects that have been fixed

— hardware compatibility

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

Use the following procedure to confirm that the signal generator powers up and that the internal check identifies no errors.

The internal check evaluates the operation of the signal generator and returns an error message if it detects a problem.

NOTE The signal generator must warm up for at least five minutes and all errors must be cleared from the error

queue before a firmware upgrade can be successfully completed.

If errors exist in the error queue and a firmware upgrade is attempted, the firmware upgrade will be

unsuccessful; new DSP code cannot be upgraded until the error queue has been cleared.

When signal generators with Option 1E5 are first connected to ac line power, the error message

ERROR 514, Reference Oven Cold occurs, causing both the OVEN COLD annunciator and the ERR

annunciator to turn on.

After approximately five minutes, the OVEN COLD annunciator automatically clears, but the ERR

annunciator remains on until all errors are cleared from the error queue.

To check signal generator functionality

1. Turn on power to the signal generator and let it warm up for at least five minutes.

2. Cycle power on the signal generator. The green LED should light and the signal generator should perform a

functionality check.

3. When the display lights, check to see if the ERR annunciator is on.

• If the ERR annunciator is on, review the error messages in the error queue by pressing

Utility > Error Info >View Next Error Message. The first error message in the error queue appears in the display

text area. (Refer to the signal generator error messages list on the documentation CD for information about each

error message.)

After resolving all problems causing errors, press ClearErrorQueue(s).

• If the ERR annunciator is off, the signal generator functionality check has passed.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Confirm Required Equipment

This section lists the minimum computer hardware, operating system, and software that are required to perform firmware

upgrades on PSG/ESG signal generators.

Computer IBM compatible PC with a 486 MHz processor or greater

RAM Required 64 MB or more

Hard Disk Space Required 20 MB or more

This could increase significantly if a large library of firmware

upgrade files are expected to be maintained on the PC. A single

firmware release consists of approximately 5 to 8 MB of data.

CD-ROM Drive or Modem Use of a CD-ROM drive is only required when the computer being

used does not have Internet access.

Use of a 56 kbps modem is only required for systems downloading

firmware updated from the Internet.

RS-232, GPIB, or LAN Connection •If you plan to perform a firmware upgrade using RS-232, refer

to the “RS-232 Installation Kit (Only for use with

Agilent E44xxB ESG Signal Generators)” on page 6.

While making the RS-232 connection, a 5-mm nut driver, part

number 8710-1219, is used to remove the screws from the

serial interface (f) to (f) adapter.

•If you plan to perform a firmware upgrade using GPIB, refer

to “GPIB Interface Requirements” on page 6.

•If you plan to perform a firmware upgrade using LAN, a

10Base-T LAN interface is required. Contact your network

administrator if problems are encountered.

Operating System Windows XP, 2000, or Windows NT 4.0 (with Service Pack 5 or

above)

Internet Browser Use of an Internet Browser is only required for downloading

firmware files from the Internet or for viewing firmware release

information on your local PC or over the Internet.

Microsoft Internet Explorer 4.0 and above, or Netscape Navigator

4.0 and above

Either browser must be Java enabled with Java 1.02 or above.

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

RS-232 Installation Kit

(Only for use with Agilent E44xxB ESG Signal Generators)

GPIB Interface Requirements

Quantity Description Part Number

1 Firmware Upgrade Guide E4400-90549

1 PSG/ESG Firmware Upgrade CD-ROM E4400-10501

1 RS-232 Cable Kit:

•Serial RS-232 Cable (8120-6188)

•RS-232 Null Modem (5181-6639)

•Adapter, (f) to (f) (1252-7825)

E4400-60049

Interface Cards Manufacturer Driver Software Version Windows Version

Agilent 82341C for

ISA bus computers Agilent Technologies I/O Libraries SICL &

VISA J.01.01.00 XP/2000/NT 4.0

Agilent 82350A for

PCI bus computers

PCI-GPIB National Instruments NI-488.2M 1.60 XP/2000/NT 4.0

PCI-GPIB+ XP/2000/NT 4.0

PCMCIA-GPIB XP/2000/NT 4.0

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Connect an RS-232, GPIB, or LAN Interface to a PC

To connect the signal generator to a PC using an RS-232 interface

(Only for use with Agilent E44xxB ESG Signal Generators)

1. Connect Agilent E44xxB ESG signal generators to the PC as shown in the following diagram. Use a 5-mm nut driver to

remove both standoffs (screws) from the female-female adapter.

RS-232 communications are connected to one of the COM ports on the PC using an RS-232 serial cable with a

null-modem connected between the COM port and the signal generator’s RS-232 connector. Refer to the “RS-232

Installation Kit (Only for use with Agilent E44xxB ESG Signal Generators)” on page 7 for more information.

NOTE Ensure that the selected COM port is not used by any other device while

PSG/ESG Upgrade Assistant 5.12 is being used.

2. Set the RS-232 parameters as follows on the Agilent E44xxB ESG signal generators:

a. Press the following keys:

Preset (factory defined)

Utility > GPIB/RS-232

RS-232 Baud Rate > 19200

RS-232 Echo > Off

RS-232 Pace >

Transmit Pace > None

Receiver Pace > Xon

RTS/CTS > RTS On

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Check Signal Generator Functionality

To connect the signal generator to a PC using a GPIB interface card

1. Connect the signal generator to the PC as shown in the following diagram.

GPIB communications require a GPIB interface card installed in the PC and a GPIB cable connected between the

interface card and the signal generator’s GPIB connector.

Two common GPIB interface cards are the National Instruments PCI–GPIB and the Agilent GPIB interface cards.

(Refer to “GPIB Interface Requirements” on page 7 and refer to the documentation that came with the GPIB interface

card for information related to installing and configuring the GPIB interface card in your computer.)

2. Set GPIB parameters as follows on PSG/ESG signal generators:

a. Press the following keys for the model being set:

b. Use the numeric keypad, the arrow keys, or rotate the front panel knob to set the desired address and press Enter.

The signal generator’s GPIB address is set to 19 at the factory. The acceptable range of addresses is 0 through 30.

Once initialized, the state of the GPIB address is not affected by a signal generator preset or by a power cycle. Other

instruments on the GPIB cannot use the same address as the signal generator.

Agilent E44xxB ESG Signal

Generators Agilent E44x8C ESG Signal

Generators Agilent E82x7C/D PSG Signal

Generators

and Agilent E824xA/5xA PSG

Signal Generators

Utility > GPIB/RS-232 >

GPIB Address > 19 Utility > GPIB/RS-232/LAN >

GPIB Address > 19

Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators

To connect the signal generator to a PC using a LAN interface card

1. Connect the signal generator to the PC as shown in the following diagram.

LAN communications require a LAN interface card installed in the PC and a LAN cable connected between the

interface card and the signal generator’s LAN connector. LAN communications require a 10Base-T LAN interface.

Contact your network administrator if problems are encountered.

2. Set LAN parameters as follows on PSG/ESG signal generators:

a. Press the following keys for the model being set:

b. Use the numeric keypad to set the desired address and press Enter.

The signal generator LAN address is not set at the factory. Contact your network administration to obtain an

appropriate IP address.

c. Set the Sockets SCPI parameters by pressing Utility > GPIB/RS-232/LAN > LAN Services Setup > Sockets SCPI:

On to use the E44x8C firmware installation tool.

Agilent E44xxB ESG Signal

Generators Agilent E44x8C ESG Signal

Generators Agilent E82x7C/D PSG Signal

Generators

and Agilent E824xA/5xA PSG

Signal Generators

LAN is not available on E44xxB

ESG Signal Generators. Utility > GPIB/RS-232/LAN >

LAN Setup > Hostname >

(enter the instrument name) or

(IP address)

Utility > GPIB/RS-232/LAN >

LAN Setup > Hostname >

(enter the instrument name) or

(IP address)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Wechselrichter Handbücher

Agilent Technologies

Agilent Technologies U9391C Service-Handbuch

Agilent Technologies

Agilent Technologies E4428C Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8648A Service-Handbuch

Agilent Technologies

Agilent Technologies MXG (Series A and B) Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83620B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 33120A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16522A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 33250A Bedienungsanleitung

Agilent Technologies

Agilent Technologies n5181a Betriebsanleitung

Agilent Technologies

Agilent Technologies 33250A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 33500 Series Service-Handbuch

Agilent Technologies

Agilent Technologies E8247C PSG CW Bedienungsanleitung

Agilent Technologies

Agilent Technologies 33220A Bedienungsanleitung

Agilent Technologies

Agilent Technologies AGILENT U2761A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8257D/67D Bedienungsanleitung

Agilent Technologies

Agilent Technologies PSG Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies E4438C ESG Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 33120A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5106A PXB Baseband Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4400-60246 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies 346A Service-Handbuch

Agilent Technologies

Agilent Technologies E4412A Service-Handbuch

Agilent Technologies

Agilent Technologies E4438C Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung