Agilent Technologies E1420B Technisches Handbuch

The following changes apply to the manuals listed below:

•Agilent E1420B User’s Manual (part number E1420-90027)

•Agilent E1420B Assembly-Level Service Manual (part number E1420-90026)

The changes contained in this Manual Update apply to all serial numbers.

Change 1: On Page A-1 (User’s Manual) and Page 1-3 (Service Manual), add the following new

information under TIME INTERVAL DELAY 1→2.

Delay Range (Option 100): 1 ms to 1 second

Change 2: On Page A-2 (User’s Manual) and Page 1-4 (Service Manual), replace the existing

specification information with the modified text below.

Change 3: On Page A-2 (User’s Manual) and Page 1-3 (Service Manual), replace the existing

information under RISE/FALL TIME 1 with the modified text below.

Range: (10 s max with 100 gate Average):

x1 Mode: 15 ns to 400 µs (auto trigger) or 800 seconds (manual trigger)

x10 Mode: 75 ns to 400 µs (auto trigger) or 800 seconds (manual trigger)

Change 4: On Page A-3 (User’s Manual) and Page 1-5 (Service Manual), replace the existing

information under EXTERNAL ARM with the modified text below.

EXTERNAL ARM:

Front panel ARM input or VXIbus TTL TRIG

lines can be used to determine Start and/or Stop

point of a measurement. External Arm can be

used with all measurements. Totalize is an exception

if the firmware is older than revision 3401.

MINIMUM, MAXIMUM AC, DC VOLTAGES 1,2

Frequency Range: dc (Input 1 only), 1 kHz to 20 MHz

Dynamic Range:

dc signals: ±10 V (xAttn)

ac signals: 200 mV (xAttn) pk-pk to 5V (x Attn) pk-pk

Resolution:

Min, Max, AC/DC: 30 mV (xAttn)

Accuracy:

Min, Max: AC ±50 mV (xAttn) ±5% of pk-pk voltage

(± 10% if x10 mode)

DC: ±50 mV (xAttn) ±5% of pk-pk voltage

(±10% if x10 mode)

SENSITIVITY 1,2 (MAX)

35 mV (xAttn) rms sine wave

100 mV (xAttn) pk-pk at a minimum pulse width of 5 ns

1 MΩ:

Dynamic Range (ac) ................... 5V (x Attn) peak to peak

Signal Operating Range (dc) ................. ±10 Volts (xAttn)

50Ω:

Dynamic Range (ac) ................................. 5V peak to peak

Signal Operating Range (dc) ................................ ±5 Volts

AC + DC not to exceed 5 Vrms

Manual Update

❒

Change 5: On Page A-3 (User’s Manual) and Page 1-4 (Service Manual), replace the existing

specification information with the modified text below.

Change 6: In the first paragraph on Page C-4 (User’s Manual) and Page 2-4 (Service Manual),

the Performance Test software is no longer available on floppy disk. However, you can download the

software from the Agilent web site at www.agilent.com (search for “E1420B”).

Change 7: On Page C-32 (User’s Manual) and Page 2-30 (Service Manual), delete Step 7 from

the procedure. After completing Step 6, proceed directly to Step 8.

Change 8: Below Step 14 on Page C-34 (User’s Manual), add the following text.

Description of Command SCPI Command String

Measure Frequency: Input 3 “MEAS3:FREQ? 1.5E9,DEF”

Verify: The E1420B measures a frequency of 1.500 000 000 GHz ± 20 Hz.

Change 9: In Step 14 on Page 2-32 (Service Manual), change the frequency tolerance from

± 2 Hz to ± 20 Hz.

Change 10: In Paragraph 3-8 on Page 3-4 (Service Manual), the correct response for firmware 3401

shown in Step 3 should be:

PASSED OFFSET CH1 , PASSED OFFSET CH2

Change 11: In Paragraph 3-9 on Page 3-4 (Service Manual), the correct response for firmware 3401

shown in Step 3 should be:

PASSED FULLSCALE CH1 , PASSED FULLSCALE CH2

Change 12: In Paragraph 3-9 on Page 3-4 (Service Manual), the +5V power source should

be accurate to 1 milliVolt.

Change 13: In Paragraph 3-10 on Page 3-4 (Service Manual), the range of acceptable MRC

bias voltages in Step 2 is from +3.000 VDC to +3.150 VDC. If your unit falls within this range,

you should not change it. If it is outside this range, set it to +3.150 VDC.

HYSTERESIS 1,2 (@1 MHz)

Adjustable to:

MINimum (35 mV rms)

MAXimum (100 mV rms)

DEFault (60 mV rms)

❒

Change 14: On Page 3-6 (Service Manual), change Step 16 to read as follows:

Repeat procedure steps 1 through 15 above until both inputs 1 and 2 on the E1420B return stable

measurements at both input frequencies and both trigger slopes. If proper lock cannot be obtained

at 28 mV, increase the signal level to 40 mV and set the adjustment pots halfway between the

optimum settings for 70 and 104 MHz. Reduce the signal level several dB and repeat until the

unit locks with a signal level of 35 mV or less. A typical unit will reach 28 mV. If the unit will not

lock at 35 mV, then the input assembly may be defective.

Change 15: On Page 3-9 (Service Manual), Step 5, change “tiomebase” to “timebase”.

Change 16: On Pages 4-11 and 4-12 (Service Manual), the correct response for Step 3 (on both pages)

should be:

HEWLETT-PACKARD,E1420B,0,3401

If the response indicates an older version, such as B.00 or C.00, upgrading the firmware to 3401

is strongly recommended.

Change 17: On Page 5-7 (Service Manual), make the following changes to Table 5-2.

Add: A1U31, E1420-80040, MRC for Standard units

Add: A1U31, E1420-80100, MRC for Option 100 units

The existing A1 part numbers are for standard units. The following part numbers apply to

units with Option 100.

A1 E1420-60120, New E1420B Option 100 motherboard

A1 E1420-69120, Exchange E1420B Option 100 motherboard

A1 E1420-60121, New E1420B Option 010 and 100 motherboard

A1 E1420-69121, Exchange E1420B Option 010 and 100 motherboard

If the motherboard for a unit with Option 040 should require replacement, the Option 040

ROMs (A1U12 and A1U13) should be taken from the old motherboard and placed in the

sockets of the new motherboard.

❒



E1420-90092

Printed in Malaysia

Edition 2

May 2002 E0502

Andere Handbücher für E1420B

Inhaltsverzeichnis

Andere Agilent Technologies Multimeter Handbücher

Agilent Technologies

Agilent Technologies 34405A Handbuch

Agilent Technologies

Agilent Technologies 3458A Betriebsanleitung

Agilent Technologies

Agilent Technologies E1326B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34405A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U3606B Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1273A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 3458A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5071C Installations- und Betriebsanleitung

Agilent Technologies

Agilent Technologies 3458A Gebrauchs- und Pflegehandbuch

Agilent Technologies

Agilent Technologies U1251B Handbuch

Agilent Technologies

Agilent Technologies 34450A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34401A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1251B Handbuch

Agilent Technologies

Agilent Technologies U1253A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1241A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8153A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1251A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1241B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34405A Handbuch

Agilent Technologies

Agilent Technologies U1253B Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1253B Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1272A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1241B Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung