Agilent Technologies HP 81130A Bedienungsanleitung
+3$¶$
3HUIRUPDQFH7HVW
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
,QWURGXFWLRQ
Use the tests in this chapter if you want to check that the HP
81130A Pulse Generator Frame with the HP 81131A 400 MHz
Output Channel(s) is working correctly. Before starting any test-
ing allow all test equipment to warm up for at least 30 minutes.
&RQYHQWLRQV8VHG
When referring to actions that you perform during the tests, the
following conventions are used:
FUNCTION This indicates that a labelled button must be pressed
[[02'(75*] This shows that a soft-key must be pressed. A soft-
key is an unlabelled button whose label is shown on the display,
and which can vary according to the job that the button is doing
&217,1828638/6(6This is an option shown on the dis-
play, and is selected by use of the vernier keys. It is shown in
upper or lower case to match the case displayed.
7HVW5HVXOWV7DEOHV
Tables for entering the results of the tests are included at the end
of this chapter. The tests are numbered and reference numbers for
each Test Result (TR) are given in a small table at the end of each
test. The reference number shows you where the actual results
should be entered in the Test Results Tables.
The Test Results tables at the end of the chapter should be photo-
copied, and the Test Results entered on the copies. Then, if the
tests need to be repeated, the tables can be copied again.
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
If Channel 2 has been fitted to your instrument, make an extra
copy of the Test Results tables for entry of the results of tests on
that channel. In this case, however, it is not necessary to repeat the
Period tests, as these are common to both channels.
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
5HFRPPHQGHG7HVW(TXLSPHQWDQG$FFHVVRULHV
The following tables list the recommended test equipment you
need to perform all the tests in this chapter. You can use alternative
instruments if they meet the critical specifications given. The test
set-ups and procedures assume you are using the recommended
equipment.
Test Equipment Model Critical Specifications
Oscilloscope
or HP 54121T 20 GHz, 10 bit vertical resolution, Histogram
Oscilloscope HP 54750A +
HP 54751A 20 GHz, 15 bit vertical resolution, Histogram
Counter
or
HP 53132A
#001/010, 030 Frequency measurements > 150 MHz
High-Stability Timebase, 3 GHz Channel
Counter HP 5334B
#010, 030 Period and Time Interval measurements
Oven Osci, 1.3 GHz C-Channel
Digital Voltmeter HP 3458A DCV up to 20 V
Delay line HP 54008A 22 ns
Accessories Model Critical Specifications
Digitizing Oscilloscopes Accessories
Attenuators
Power Splitter
SMA/SMA (m-m) adaptor
SMA (f)/BNC (m) Adaptor
SMA (m)/BNC (f) Adaptor
SMA Cable
HP 33340C#020
HP 33340C#006
HP 11667B
1250-1159
1250-1700
1250-1200
8120-4948
20 dB
6 dB
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
127( When you connect the test equipment for the first time, and
whenever you change the setup during the course of these tests,
use the 8710 - 1582 torque wrench to tighten and loosen SMA
connectors. This will ensure that the connectors are at the correct
tightness and give the best signal transfer.
50 Ω Feedthrough Termination HP 10100C
6HH)LJXUH
2 W,1%
10 W,0.1%
Adaptor 1251-2277 BNC to Banana
Cable Assemblies, BNC 8120-1839
Torque Wrench 8710-1582 5/16 in, 5 lb-in (56 Ncm)
Accessories Model Critical Specifications
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
2KP:)HHGWKURXJK7HUPLQDWLRQ
The following figure provides a schematic and a parts list except
for the case. The case must provide shielding and maintain
grounding integrity.
50 Ohm, 0.1%, 10 W Feedthrough Termination
The following parts are required:
1. R1 = 53.6Ω, 1%, 10 W; HP Part Number: 0699-0146.
2. R2 = 200 Ω, 10%, 0.5 W, Variable trimmer; HP Part Number:
100-3350.
3. R3 = 681 Ω;, 1%, 0.5 W; HP Part Number: 0757-0816.
4. BNC (M): HP Part Number: 1250-0045.
5. BNC (F): HP Part Number: 1250-0083.
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
*HWWLQJ6WDUWHG
The HP 81130A is controlled by selecting options in a series of
SDJHV that are displayed on the instrument’s screen. These options
vary with the boards that are fitted in the instrument. When the HP
81130A is being tested, therefore, different situations can arise,
depending on whether you have a standard instrument or one that
has had additional boards fitted. The following examples illustrate
this
7\SLFDO([DPSOHVRI'LVSOD\HG6FUHHQV
The OUTPUT Screen in a Standard HP 81130A
3HU
µ
V
287387 3$77(51/,0,7602'(75*
2))
'HOD\
SV
:LGWK
/HDG(
7UDL(
QV
QV
/HDG(
2IIVHW
$PSOLW
P9
9
2))QRUP
21RXW
02',)<
2))
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
The TIMING Screen in an HP 81130A with qty 2 of HP 81131A
The LEVELS Screen in an HP 81130A with qty 2 of HP 81131A
7,0,1* 3$77(51/(9(/602'(75*
'HOD\
2))
µ
V2))
3HULRG
)UHTXHQF\
02',)<
SV
:LGWK
/HDG(
7UDL(
QV
QV
'HOD\ SV
:LGWK
/HDG(
7UDL(
QV
QV
/HDG(
3HU
/HDG(
2))2))
2121
7,0,1* 3$77(51/(9(/602'(75*
9
P9
2IIVHW P9
$PSOLW 9
02',)<
6HW77/
+LJK/RZ
2IIV$PSO
6HW(&/
+LJK
/RZ
2))2))
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
,QVWUXPHQW6HULDO1XPEHUV
You will need to write the serial numbers of the instrument at the
top of the Test Reports. These can be found as follows:
Press HELP, [6(5,$/]
The HP 81130A display lists the instrument’s products and serial
number.
The display on your instrument should look similar to this:
The serial number given for the )5$0( applies to the Mainframe,
the Power Supply, the Microprocessor Board, and the Timing
Board. The number(s) available of the Output Channel(s) applies
to the installed numbers of outputs and Model Number.
)5$0(
6HULDO1R
2873876
&K%G
&K%G
$0+]
'(%
$
$
+3$¶$3HUIRUPDQFH7HVW
HP 81130A/’31A Performance Test
,QLWLDO6HWXSRIWKH+3$
In the majority of these tests the initial setting up of the instrument
is identical. Therefore, it is described once here, and then referred-
to where appropriate. In cases where the initial setup differs, an
illustration of the settings is shown.
Set up the HP 81130A as follows:
1. Select [02'(75*]
&217,1828638/6(6
2. Select [287387], if second channel is installed
•6HSDUDWH2XW
3. Select MORE [&21),*] screen and set up as follows.
If a second output channel is installed select grouped by OUT-
PUT 1 / 2
CONFIG Screen, Parameters grouped by OUTPUT
75*/(9 &21),*0(0&$5'/,0,76
+3,%$GGUHVV
7LP/HY
2XW
3HUIRUP6HOIWHVWX3DQG6LJQDO
3//5HI,QWHUQDO
'HVNHZSVSV
02',)<
*URXS3DUDPVE\287387
3XOVH3HULRGLQWHUQDO3//
Dieses Handbuch passt für folgende Modelle
1
Andere Agilent Technologies Tragbarer Generator Handbücher
Agilent Technologies
Agilent Technologies Agilent 33500 Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies E8663B Bedienungsanleitung
Agilent Technologies
Agilent Technologies E4438CK-601 Installations- und Betriebshandbuch
Agilent Technologies
Agilent Technologies N4000A Service-Handbuch
Agilent Technologies
Agilent Technologies E4428C Bedienungsanleitung
Agilent Technologies
Agilent Technologies E4438C Bedienungsanleitung
Agilent Technologies
Agilent Technologies E8663B Bedienungsanleitung
Agilent Technologies
Agilent Technologies N4971A Bedienungsanleitung
Agilent Technologies
Agilent Technologies E8306A Bedienungsanleitung
Agilent Technologies
Agilent Technologies 81110A Bedienungsanleitung
Agilent Technologies
Agilent Technologies 85901A Bedienungsanleitung
Agilent Technologies
Agilent Technologies E8267C Bedienungsanleitung
Agilent Technologies
Agilent Technologies ESG-D Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies E8267C Betriebsanleitung
Agilent Technologies
Agilent Technologies 8340B Bedienungsanleitung
Agilent Technologies
Agilent Technologies 8360B Bedienungsanleitung
Agilent Technologies
Agilent Technologies 8360B Bedienungsanleitung
Agilent Technologies
Agilent Technologies PSG Series Kurzanleitung
Agilent Technologies
Agilent Technologies ESG-D Series Konfigurationshandbuch
Agilent Technologies
Agilent Technologies ESG-D Series Kurzanleitung
