Agilent Technologies 93000 SOC Series Installationsanleitung

Training Manual

Agilent 93000 SOC Series

Mixed-Signal Training

Name

Company

Location

Date

Agilent 93000 SOC Series

MIxed Signal Training

Revision 4.3.0 (August 2004)

SOC-BU

System on a Chip Business Unit

This document contains proprietary

information which is protected by

The information in this document is

subject to change without notice.

Agilent Technologies makes no war-

ranty of any kind with regard to

this printed material, including, but

not limited to, the implied warran-

ties of merchantability and fitness

for a particular purpose.

Agilent Technologies shall not be li-

able for errors contained herein or

consequential damages in connec-

tion with the furnishing, perfor-

mance, or use of this material.

Contents

Unit 1 Introduction

Lesson 1

Training Overview

1-1 About This Training .......................................................................15

1-2 The Study Material .........................................................................19

Lesson 2

Introduction to the Test System

2-1 Components of SOC Devices.........................................................23

2-2 SOC Series Mixed-Signal System Overview ................................25

2-3 Questions .........................................................................................33

2-4 Summary and Discussion ..............................................................34

Lesson 3

Introduction to the Software

3-1 SmarTest Software Concept Overview ........................................37

3-2 Tools for Mixed-Signal Testing .....................................................39

3-3 Questions .........................................................................................54

3-4 Summary and Discussion ..............................................................56

Unit 2 Analog Hardware

Lesson 1

Analog Modules

1-1 Summary of Analog Modules ........................................................61

1-2 Arbitrary Waveform Generators (AWG) .....................................62

1-3 Waveform Digitizer.........................................................................73

1-4 Sampler ............................................................................................87

1-5 Time Interval Analyzer ..................................................................94

1-6 Pin Connections with an Analog Module’s Multiplexer............99

1-7 Multi-site Baseband Analog Source&Measure / Analog Measure

(MCA) ............................................................................................ 104

Contents

Lesson 2

Addressing the Analog Modules

2-1 Locations of Analog Boards in the Testhead ........................... 131

2-2 Analog Pins of the Board............................................................ 134

2-3 Identification of Analog Channels in the Software ................ 139

Lesson 3

Synchronization of Analog Modules

3-1 Synchronization + Triggering..................................................... 146

3-2 Adjusting the Synchronization Timing ..................................... 151

Unit 3 DAC Test Setup and Execution

Lesson 1

The Training DAC

1-1 DAC Basics.................................................................................... 157

1-2 Characteristics of the Training DAC......................................... 159

1-3 Mixed-Signal Test Setup Procedure .......................................... 161

1-4 Summary and Discussion ........................................................... 164

Lesson 2

Waveform Digitizer Setup with the Analog Setup Tool

2-1 Functions of the Analog Setup Tool.......................................... 167

2-2 Starting the Analog Setup Tool.................................................. 175

2-3 Core Selection and Global Functions........................................ 177

2-4 Setting Up the Analog Hardware............................................... 181

2-5 Setting Up Sequencer Program and Waveform Memory Labels ..

184

2-6 Reviewing and Changing the Waveform Memory ................... 192

2-7 Viewing the Relay Multiplexer Switches .................................. 194

2-8 Summary and Discussion ........................................................... 196

Contents

Lesson 3

Setting up the Digitizers in the Digital Clock Domain

3-1 What is a Clock Domain.............................................................. 199

3-2 Clock Sources and Clock Distribution Overview .................... 200

3-3 Digital Clock Domain Setup for the Digitizer .......................... 203

3-4 Summary and Discussion ........................................................... 208

Lesson 4

Defining the Signal Routing

4-1 Analog Routing Basics ................................................................ 211

4-2 Overview of the Routing Setup Tool ......................................... 213

4-3 Setting up the DAC Routing ....................................................... 216

4-4 Activating a Routing Set ............................................................. 221

4-5 Viewing the Active Routing ........................................................ 222

4-6 Summary and Discussion ........................................................... 223

Lesson 5

Waveform Generation with the Mixed-Signal Tool

5-1 Functions of the Mixed-Signal Tool .......................................... 227

5-2 Starting the Mixed-Signal Tool .................................................. 229

5-3 Customizing the Mixed-Signal Tool........................................... 231

5-4 Saving and Restoring Waveforms.............................................. 234

5-5 Generating Waveforms................................................................ 236

5-6 Downloading a Generated Waveform ....................................... 248

5-7 Related Topics .............................................................................. 250

5-8 Summary and Discussion ........................................................... 251

Contents

Lesson 6

Executing the DAC Linearity Test

6-1 DAC Linearity Measurements.................................................... 255

6-2 DAC Linearity Test Parameters................................................. 261

6-3 Uploading Result Waveforms with the Mixed-Signal Tool..... 263

6-4 Displaying Logged Waveforms with the Mixed-Signal Tool... 266

6-5 Related Topics .............................................................................. 270

6-6 Summary and Discussion ........................................................... 271

Lesson 7

Executing the DAC Distortion Test

7-1 DAC Distortion Measurements .................................................. 275

7-2 DAC Distortion Test Parameters ............................................... 280

7-3 Analyzing Spectral Data with the Mixed-Signal Tool ............. 282

7-4 Summary and Discussion ........................................................... 287

Unit 4 ADC Test Setup and Execution

Lesson 1

The Training ADC

1-1 ADC Basics.................................................................................... 293

1-2 Test Setup Overview for ADC Tests.......................................... 299

1-3 Characteristics of the Training ADC......................................... 301

1-4 Summary and Discussion ........................................................... 302

Lesson 2

Setting Up the Waveform Generator

2-1 Waveform Generator Setup with Analog Setup Tool ............. 305

2-2 Defining and Downloading a Waveform to the AWG ............. 317

2-3 Signal Routing .............................................................................. 320

2-4 Summary and Discussion ........................................................... 321

Contents

Lesson 3

Setting Up the Digital Capturing

3-1 Introduction to Digital Capture................................................. 325

3-2 Setup for Digital Capture............................................................ 328

3-3 Summary and Discussion ........................................................... 340

Lesson 4

Executing the ADC Linearity Test

4-1 ADC Linearity Measurements.................................................... 343

4-2 ADC Linearity Test Parameters................................................. 347

4-3 Uploading Result Waveforms with the Mixed-Signal Tool .... 349

4-4 Summary and Discussion ........................................................... 351

Lesson 5

Executing the ADC Distortion Test

5-1 ADC Distortion Measurements.................................................. 355

5-2 ADC Distortion Test Parameters............................................... 357

5-3 Summary and Discussion ........................................................... 360

Unit 5 Using the Analog Clock Domain

Lesson 1

Analog Clock Domain Description

1-1 Clock Domains Summary ........................................................... 365

1-2 Clock Sources and Clock Distribution...................................... 366

1-3 Clock Distribution between Card Cages................................... 370

1-4 Summary and Discussion ........................................................... 375

Lesson 2

Analog Clock Domain Setup

2-1 Overview of Analog Clock Domain Setup Parameters ........... 379

2-2 Analog Clock Domain Setup Procedure ................................... 382

2-3 Analog Module Setup Interdependencies ................................ 387

2-4 Summary and Discussion ........................................................... 393

Contents

Unit 6 Using Test Methods

Lesson 1

Test Method Structure

1-1 Test Method Overview................................................................. 399

1-2 Data Types .................................................................................... 403

1-3 Input/Output Data of Test Method Program ........................... 405

1-4 Programming Style of Test Method API ................................... 409

1-5 Test Method APIs ......................................................................... 414

1-6 Test Method Program for DC Tests ........................................... 425

Lesson 2

Creating a Test Method

2-1 Overview........................................................................................ 433

2-2 Preparations to Develop a Test Method Program ................... 436

2-3 Using the Text Editor for Editing a Test Method Program.... 441

2-4 Compiling and Linking Test Method Programs....................... 445

2-5 Registering a Test Method Shared Library .............................. 447

2-6 Setting Up Testmethod-Based Test Suite ................................. 448

2-7 Executing Testmethod-Based Test Suite .................................. 453

2-8 Debugging Test Method Programs............................................. 456

2-9 Debugging Tests using Hardware Response Emulator........... 463

Unit 7 Time Interval Analyzer

Lesson 1

TIA Overview

1-1 Front-End Module and Time Interval Analyzer (TIA)............ 471

1-2 Setup and Test Execution Overview ......................................... 473

1-3 Summary and Discussion ........................................................... 475

Contents

Lesson 2

TIA Setup

2-1 Overview ....................................................................................... 479

2-2 Pin Configuration for the TIA .................................................... 480

2-3 Front-End and TIA Setup ........................................................... 481

2-4 Defining the Routing ................................................................... 493

2-5 Summary and Discussion ........................................................... 495

Lesson 3

TIA Test Method Programming and Test Execution

3-1 Test Method Flow ........................................................................ 499

3-2 TIA API Functions ....................................................................... 501

3-3 TIA Example Test Method .......................................................... 504

3-4 Summary and Discussion ........................................................... 507

Unit 8 Advanced Procedures

Lesson 1

Multi-Site Test

1-1 Overview ....................................................................................... 513

1-2 Defining Pin Configuration ........................................................ 515

1-3 Setting Up Flags for Multi-Site Testing..................................... 516

1-4 Test Method Program for Multi-Site Testing............................ 517

Lesson 2

DUT Board Design Considerations

2-1 DUT Board Overview .................................................................. 529

2-2 DUT Board Design Consideration ............................................. 531

2-3 Grounding and Signal Shielding................................................ 533

2-4 Printed Circuit Board.................................................................. 536

2-5 Troubleshooting Noise Problems............................................... 539

2-6 Summary and Discussion ........................................................... 540

Contents

Lesson 3

Special Synchronization Options

3-1 Master/Slave Trigger Function .................................................. 543

Appendix

Andere Handbücher für 93000 SOC Series

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies 8960 Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5022B Betriebsanleitung

Agilent Technologies

Agilent Technologies 3070 Series Benutzerhandbuch

Agilent Technologies

Agilent Technologies 16034E Bedienungsanleitung

Agilent Technologies

Agilent Technologies E7474A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U3042AE08 Bedienungsanleitung

Agilent Technologies

Agilent Technologies Ininiium 9000 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54522A Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85057B Handbuch

Agilent Technologies

Agilent Technologies 16533A 1-GSa/s Handbuch

Agilent Technologies

Agilent Technologies 1153A Fehlerbehebungshandbuch

Agilent Technologies

Agilent Technologies 3000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85110L Handbuch

Agilent Technologies

Agilent Technologies N9360A Betriebsanleitung

Agilent Technologies

Agilent Technologies 3000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85052B Handbuch

Agilent Technologies

Agilent Technologies Agilent 34980A Montage- und Bedienungsanleitung

Agilent Technologies

Agilent Technologies 81101A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5515BU-863 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies E4400-60598 Kurzanleitung

Agilent Technologies

Agilent Technologies ProBER 2 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 81250 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8156A Betriebsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung

Sealey

Sealey TA130 Bedienungsanleitung