Agilent Technologies E4400-60598 Kurzanleitung

Installation Note

Part Number E4400-90550

Printed in USA May 2002

Supersedes April 2002

Agilent Technologies ESG Vector Signal Generator

Upgrade Kit for Option 002

(Internal Baseband Generator with 32 Msample Memory)

Kit Part Number E4400-60598

Notice

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. Agilent

Technologies shall not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

ESG Vector Signal Generator Upgrade Kit for

Option 002 (Internal Baseband Generator with 32 Msample

Memory)

Kit Part Number E4400-60598

Introduction

This upgrade kit adds the Internal Baseband Generator with 32 Msample Memory to the E4438C.

NOTE This upgrade kit contains hardware for both the standard front panel connector setup and

Option 1EM rear panel connector setup.

Installation includes the following major steps:

1. Check Functionality.

2. Remove the instrument covers.

3. Install the A7 Internal Baseband Generator board.

4. Install new firmware.

5. Activate Option 002.

6. Re-assemble the signal generator.

7. Calibrate the signal generator.

Product Affected: . . . . . . . . . . . . . . . . . . . . . . . . . E4438C

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . All

Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Technologies Service Center

(X) Personnel Qualified by Agilent Technologies

( ) Customer

Estimated Installation Time: . . . . . . . . . . . . . . . 0.5 hours

Estimated Verification Time: . . . . . . . . . . . . . . . 1.0 hours

Installation Kit Parts List

Tools Required

• TORX T-10 driver

• TORX T-15 driver

• TORX T-20 driver

• Needle-Nose pliers

• 1/4 socket

•9/16socket

• Ratchet 21 in-lb.

• Hand Torque wrench 9 in-lb.

Safety Considerations

WARNING Before you disassemble the instrument, turn the power switch off and

unplug the signal generator. Failure to unplug the signal generator can

result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Item Quantity Description Part Number

Installation Note E4400-90550

2 1 ESG-C Firmware Upgrade Kit E4400-60597

3 1 Option 002 Label 7121-1232

4 1 A7 Internal Baseband Generator 32 Msample Memory E4400-60501

5 1 W10 Ribbon Cable 8121-0679

For Non Option 1EM signal generators only

Cable-BNC W12 8121-0643

Hex Nut 15/21-32 2950-0035

Washer 0.4721D 2190-0102

For Option 1EM signal generators only

Cable-SMB W78 8121-0655

10 1 Hex Nut SMB 2950-0078

11 1 Washer SMB 2190-0124

Checking Signal Generator Functionality

Use the following procedure to confirm that the signal generator powers up and that the internal check

identifies no errors. The internal check evaluates the operation of the signal generator and returns an error

message if it detects a problem.

NOTE When signal generators with Option 1E5 are first connected to ac line power, the error

message ERROR 514, Reference Oven Cold occurs which causes both the OVEN COLD

annunciator and the ERR annunciator to turn on.

After approximately five minutes, the OVEN COLD annunciator automatically clears, but the

ERR annunciator remains on until all errors are cleared from the error queue.

1. Turn on the signal generator and let it warm up for at least five minutes.

2. Run the instrument self-test by pressing Utility > Instrument Info/Help Mode > Self Test > Run Complete Self

Test. Upon completion a summary of the self-test will be displayed. Use the service guide to troubleshoot

any failures detected by the test.

NOTE Some circuits may require up to 50 minutes to warm up before passing the self-test. If

self-tests continue to fail after 50 minutes of warm up, troubleshoot the instrument.

3. Check to see if the ERR annunciator is on.

•IftheERR annunciator is on, review the error messages in the error queue by pressing

Utility > Error Info >View Next Error Message. The first error message in the error queue appears in the

display text area. (Refer to the signal generator error messages document for information about each

error message.)

After resolving all problems causing errors, press Clear Error Queue(s).

•IftheERR annunciator is off, the signal generator functionality check has passed.

Removing Outer and Inner Covers

Tools Required

•T-10driver

•T-15driver

•T-20driver

Removing the Outer Cover

Refer to Figure 1.

1. Disconnect the power cord.

2. Using a T-20 driver, remove the two strap handles (1) by loosening the screws.

3. Using a T-15 driver, remove the center screws (3) on the four rear-panel feet (2).

4. Remove the four bottom feet (5) and (6) from the cover by pushing and pulling the tab.

5. Slide the outer cover (4) off the frame.

Removing the Inner Top Cover

Refer to Figure 1.

1. Using a T-10 driver, remove the ten screws (8) from the inner-top cover (7).

2. Remove the inner-top cover.

Figure 1 Outer and Inner Cover Removal

Figure 2

NOTE Use the following procedure only if the instrument does not include Option 1EM.

Installing the A7 Internal Baseband Generator Board

Refer to Figure 2 for this procedure.

1. Locate Top-SLOT 1.

2. Insert the A7 assembly into the front and rear card cage guides.

3. Install the A7 Assembly onto the A23 motherboard.

4. Install the W12 cable to the rear panel slot labeled “BASEBAND GEN REF IN”. Use a lock washer and

a hex-nut to secure one end of the cable to the rear panel. Torque to 21 in-lb.

5. Connect the loose end of the W12 cable to A7J800.

6. Connect W10 from A25P2 of the rear panel board to A7J13.

NOTE Use the following procedure only for instruments with Option 1EM.

Installing the A7 Internal Baseband Generator Board

Refer to Figure 2 for this procedure.

1. Locate Top-SLOT 1.

2. Insert the A7 assembly into the front and rear card cage guides.

3. Install the A7 Assembly onto the A23 motherboard.

4. Install the W78 cable to the rear panel slot labeled “BBG REF IN”. Use a lock washer and a hex-nut to

secure one end of the cable to the rear panel. Torque to 9 in-lb.

5. Connect the loose end of the W78 cable to A7J800.

6. Connect W10 from A26P2 of the rear panel board to A7J13.

Verifying Proper Installation of Option 002

1. Perform the “Checking Signal Generator Functionality, as described on page 5.

2. Verify that the Baseband Generator self-tests 16xx are included in the list and that all pass.

Installing New Firmware

1. The firmware upgrade kit contains an installation note. Using the installation note, install the new

firmware.

2. Perform the verification procedure described in the firmware upgrade installation note.

Re-Assembling the Instrument

Refer to Figure 1.

1. Reinstall the inner and outer instrument covers by reversing the order for removal.

2. Torque all T-10 screws to 9 in-lbs.

3. Torque all T-15 and T-20 screws to 21 in-lbs.

4. Attach the Option 002 label provided to the rear panel, near the original serial number label.

Re-Calibrating the Instrument

Refer to the ESG Vector Signal Generator Service Guide.

1. Turn the instrument on and let it warm up for 30 minutes.

2. Perform the following A7 Baseband Generator adjustments, in the order listed:

•SelfTest

• I/Q Gain/Offset/Quadrature Calibration

• I/Q Impairment Calibration

Verifying Instrument Calibration

To ensure proper calibration of the A7 Baseband Generator use the following performance tests, in the

order listed:

•SelfTest

• Harmonic, Subharmonic, and Nonharmonic Spurious Signals

• Digital Modulation Level Accuracy

• Internal Digital Modulation Quality (Option 402 only)

• Custom I/Q RF Modulation Quality (Option 402 only)

• CDMA Adjacent Channel Power (Not Used with Option UNB or Option 506)

• WCDMA Adjacent Channel Power (Option 400)

• Dual Arbitrary Waveform Generator Check

• GSM Loopback BER Check (Option 300 only)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies N4010A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Series 10 Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 7000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies TS-5400 Stücklistenhandbuch

Agilent Technologies

Agilent Technologies E6630A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54621A Handbuch

Agilent Technologies

Agilent Technologies 85057B Handbuch

Agilent Technologies

Agilent Technologies E1852B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54622A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16048E Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85056D Handbuch

Agilent Technologies

Agilent Technologies U3042AE08 Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8922 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16047E Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16533A 1-GSa/s Handbuch

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Bedienerhandbuch

Agilent Technologies

Agilent Technologies N9360A Betriebsanleitung

Agilent Technologies

Agilent Technologies 85050C Handbuch

Agilent Technologies

Agilent Technologies 3000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1583A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 81250 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung