Agilent Technologies E840 A Series Installations- und Betriebshandbuch

Installing the Tinted Acrylic Door

Installation Note

!"Installation Note

Installing the Tinted Acrylic Door

This procedure describes how to install the Tinted Acrylic Door on the

Agilent E840xA mainframe. The doorrequires mainframe Standard Adapter

Kit Option AXA (p/n E8400-80923), and is compatible with either the

support rail kit (Agilent E3664AC) or the rack slide kit (p/n 1494-0411).

Parts List The parts included in the door kit are shown in Table 1.

Note The door requires the mainframe to be recess mounted a minimum of

111 mm (4.36") or up to a maximum of 270.7 mm (10.6 inches) to

accommodate wiring terminals on the VXI instruments. When using the

minimum recess distance, field wiring cables must enter/exit the

instruments through the top and/or bottom openings only.

Procedure 1. Recess mount the mainframe a minimum of 111 mm (4.36 inches)

using the Standard Adapter Kit and either the support rail kit or rack

slide kit (see E8400-90038 for mainframe mounting instructions).

Note For the minimum recess distance, attach the rack mount adapters to the

mainframe beginning with the 12th hole from the front of the adapter.

2. If necessary, remove the dress screws (0570-1577) securing the

adapters to the rack.

3. Attach the hinge pins to the right rack mount adapter using four 10-32

x 0.375 flat head screws (Figure 1). Attach the rubber door stops and

door latch to the left adapter using four m3x8 pan head screws as also

shown in Figure 1.

Table 1. Agilent E840xA Door Kit Parts List.

Quantity Description Part Number

1 Acrylic Door Assembly E8400-09301

2 Hinges 3110-0409

1 Door Latch, Lock, and Keys 1390-0891

2 Rubber Door Stops 0403-0002

4 Screws - 10-32x0.375 flat head 2680-0100

4 Screws - m3x8 pan head 0515-0897

*E8400-90039*

Manual Part Number: E8400-90039

Edition 3 E0309

Installing the Tinted Acrylic Door Installation Note

4. Slide mainframe into the rack until the rack mount adapters contact

the rack’s vertical rails. Start the dress screws but do not tighten.

5. Install the door assembly by placing the hinges over the hinge pins on

the right adapter. Adjust the door for squareness and clearance by

holding the door in place while tightening the dress screws.

6. Adjust the latch keeper so that the door latches as it makes contact

with the rubber door stops.

Note Once installed and adjusted, the door can be removed when necessary by

lifting the door off the hinge pins.

Figure 1 . Installing the Acrylic Door Hinges, Door Stops, and Latch Keeper.

Rubber Door

Stop

Door

Latch

10-32 x 0.375

Flat Head Screws

10-32 x 0.375

Flat Head

Hinge

Pins

m3x8

Pan

Head

Screws

Rubber

Door

Stop

Screws

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies InfiniiVision 7000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 3000 Series Handbuch

Agilent Technologies

Agilent Technologies E7490A Bedienungsanleitung

Agilent Technologies

Agilent Technologies J-BERT N4903 Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Handbuch

Agilent Technologies

Agilent Technologies 86100A Anleitung zur Verwendung

Agilent Technologies

Agilent Technologies 85056K Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Handbuch

Agilent Technologies

Agilent Technologies InfiniiVision 2000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infiniium 9000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Handbuch

Agilent Technologies

Agilent Technologies U1610/20A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Series 10 Bedienungsanleitung

Agilent Technologies

Agilent Technologies N9360A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infiniium 90000 X Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5035A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Medalist x6000 Bedienungsanleitung

Agilent Technologies

Agilent Technologies ACQIRIS CC103 Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5230-60102 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies N5980A Betriebsanleitung

Agilent Technologies

Agilent Technologies 54845B Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E6198B Bedienungsanleitung

Agilent Technologies

Agilent Technologies HP 83711A Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung

Sealey

Sealey TA130 Bedienungsanleitung