AGRI EASE BE-FM RDG Series Anwendungshandbuch

BE-FMxRDG

Rear Discharge

Finish Mower

Operations & Parts Manual

• BE-FM48RDG

• BE-FM60RDG

• BE-FM72RDG

For Models:

Purchase Date

Dealer

Model No. Serial No.

This manual contains valuable information about your new mower.

It has been carefully prepared to give you helpful suggestions for operating, adjusting and servicing.

Keep this manual in a convenient place for quick and easy reference.

Study it carefully, only by proper care and operation can you expect to receive the service and long life

designed and built into this mower.

It is the owner’s and/or operator’s responsibility to:

• Read and understand the information contained in this manual.

• Operate, lubricate, assemble and maintain the equipment in accordance with all instructions and

safety procedures in this manual.

• Inspect the equipment and replace or repair any parts that are damaged or worn which could cause

damage, wear to other parts or cause a safety hazard.

TO THE CUSTOMER

BE-FMxRDG

Keep safety signs clean and legible at all times.

Do not paint over, remove or deface any safety signs or warning signs on your equipment.

Observe all safety signs and practice the instruction on them.

Replace safety signs that are missing or have become illegible. Replaced parts that displayed a safety sign

should also display the current sign.

Safety signs are available from your Distributor.

How To Install Safety Signs:

• Be sure that the installation are is clean and dry.

• Be sure temperature is above 50°F (10°C).

• Decide on the exact position before you remove the backing paper.

• Remove the smallest portion of the split backing paper.

• Align the sign over the speciﬁed area and carefully press the small portion with the exposed

sticky backing in place.

• Slowly peel back the remaining paper and carefully smooth the remaining portion of the sign backing paper.

• Small air pockets can be pierced with a pin and smoothed out using the piece of sign backing paper.

SAFETY SIGNS

Safety of the operator is one of the main concerns in designing and developing a new piece of equipment.

Designers and manufacturers build in as many safety features as possible.

However, every year many accidents occur which could have been avoided by a few seconds of thought and a

more careful approach to handling equipment.

You, the operator, can avoid many accidents by observing the following safety precautions in this section.

To avoid personal injury, study the following precautions and insist those working with you, or for you follow them.

In order to provide a better view, certain photographs or illustrations in this manual may show an assembly with

safety shield removed. However, equipment should never be operated in this condition. Keep all shields in place.

If shield removal becomes necessary for repairs, replace the shield prior to use.

Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this equipment.

Consult your doctor about operating this machine while taking prescription medications.

Review the instructions with all users annually. This equipment is dangerous to children and persons unfamiliar

with its operation. The operator should be a responsible adult familiar with farm machinery and trained in this

equipment’s operations. Do not allow persons to operate or assemble this unit until they have read this manual

and have developed a thorough understanding of the safety precautions and of how it works.

To prevent injury or death, use a tractor equipped with a Roll-Over Protective System (ROPS).

Never exceed the limits of a piece of machinery.

If its ability to do a job, or to do so safely, is in question DON’T TRY IT!

Do not modify the equipment in any way. Unauthorized modiﬁcation may impair the function and/or safety

and could aect the life of the equipment.

In addition to the design and conﬁguration of this implement, including Safety Equipment, hazard control and

accident prevention are dependent on the awareness, concern, prudence and proper training of personnel

involved in the operation, transport, maintenance and storage of the machine. Refer also to Safety Messages and

Operations Instructions in each of the appropriate sections of the Tractor and Mower Manuals.

Pay close attention to the Safety Signs axed to the Tractor and the Mower.

EQUIPMENT SAFETY GUIDELINES

BE-FMxRDG

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our eorts to provide

safe equipment can be wiped out by a single careless act of an operator.

In addition to the design and conﬁguration of equipment, hazard control and accident prevention are dependent

upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport,

maintenance and storage of equipment.

It is the operator’s responsibility to read and understand ALL Safety and Operating instructions in the manual

and to follow them. Accidents CAN be avoided.

Working with unfamiliar equipment can lead to careless injuries. Read this manual and the manual for your

tractor before assembling or operating your mower, to acquaint yourself with the machines.

It is the rotary mower owner’s responsibility if this machine is used by any person other than yourself,

to make certain that the operator, prior to operating:

• Reads and understands the operator’s manuals.

• Is instructed in safe and proper use.

Know the controls and how to stop tractor, engine and mower quickly in an emergency. Read this manual

and the one provided with your tractor.

Train all new personnel and review instructions frequently with existing workers. A person who has not read

and understood all operating and safety instructions is not qualiﬁed to operate the machine. An untrained

operator exposes himself and bystanders to possible serious injury or death.

Do not allow children to operate this machine.

SAFETY TRAINING

BE-FMxRDG

Never operate the tractor and mower until you have read and completely understand this manual, the Tractor

Operator’s Manual and each Safety Messages found on the safety signs on the tractor and mower.

Personal protection equipment including hard hat, safety glasses, safety shoes and gloves are recommended

during assembly, installation, operation, adjustment, repairing, removal or moving the implement.

Do not wear loose clothing, gloves, neckties, rings bracelets or other jewelry which may get caught

in moving parts. Wear protective hair covering to contain long hair.

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS!

Tractors with or without Mowers attached can often be noisy enough to cause permanent or partial hearing loss.

We recommend that your wear hearing protection on a full-time basis if the noise in the Operator’s position

exceeds 80db. Noise over 85db on a long-term basis can cause sever hearing loss. Noise over 90db adjacent to

the Operator over a long-term basis may cause permanent, total hearing loss.

NOTE: Hearing loss from loud noise (from tractors, chain saws, radios and other such sources close to the ear) is

cumulative over a lifetime without hope of natural recovery.

Operate the mower only with a tractor equipped with an approved Roll-Over Protective System (ROPS).

Always wear your seatbelt on tractors equipped with a ROPS. Serious injury or even death could result from

falling o the tractor - particularly during a turnover when the operator could be pinned under the ROPS

or the

tractor.

Clear area to be cut of stones, branches or other debris that might be thrown, causing injury or damage.

Operate only in daylight or good artiﬁcial light.

Ensure mower is properly mounted, adjusted and in good operating condition.

Ensure that all safety shielding and safety signs are properly installed and in good condition.

PREPARATION

BE-FMxRDG

The use of this equipment is subject to certain hazards which cannot be protected against by mechanical means

or product design. All operators of this equipment must read and understand this entire manual, paying particular

attention to safety and operating instructions, prior to using. If there is something in this manual you do not

understand, ask your supervisor or your dealer to explain it to you.

Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders at least several

hundred feet away from an operating rotary mower. Only properly trained people should operate this machine.

When this machine is operated in populated areas or in other areas where thrown objects could injure persons

or property, standard equipment safety chain shielding (which is designed to reduce the possibility of thrown

objects) must be installed. Operation must be stopped when anyone comes within 100 yards (300 feet).

The majority of accidents involve entanglement on the driveline, injury of bystanders by objects thrown by the

rotating blades and being knocked o the tractor by low hanging limbs and then being run over by the mower.

Accidents are most likely to occur with machines that are loaned or rented to someone who has not read the

owner’s manual and is not familiar with a rotary mower.

Check the tractor master shield over the PTO shaft. Make sure it is in good condition and fastened securely

to the tractor. Purchase a new shield if old shield is damaged or missing.

OPERATIONAL SAFETY

Mower operating power is supplied from tractor PTO. Refer to your tractor manual for PTO engagement and

disengagement instructions. Always operate the tractor PTO in the 540 RPM speed selection.

DO NOT OVER SPEED! Know how to stop tractor and mower quickly in case of an emergency.

When engaging PTO, the engine RPM should always be low. Once engaged and ready to start cutting, raise PTO

speed to approx. 540 RPM and maintain throughout cutting operation.

Always stop the tractor, set brake, shut o the tractor engine, remove ignition key, lower implement to the

ground and allow cutter blades to come to a complete stop before dismounting tractor.

Never leave equipment unattended with the tractor running or with implement in raised position.

STARTING AND STOPPING SAFETY

Following operation, or when unhooking, stop the tractor, set the brakes, disengage the PTO, shut o the engine

and remove the ignition keys.

Store the unit in an area away from human activity.

Do no park equipment where it will be exposed to livestock for long periods of time.

Equipment damage and livestock injury could result.

Do not permit children to play on or around the stored unit.

Make sure all parked machines are on a hard, level surface and engage all safety devices.

If blocking is used, make sure it is solid and secure before leaving.

STORAGE SAFETY

BE-FMxRDG

Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed building.

The exhaust fumes may cause asphyxiation.

Before working on this machine, drive to a level area, disengage the PTO, lower the implement (or if working

underneath, raise and block securely), shut o the engine, set the brakes and remove the ignition keys.

Be certain all moving parts on attachments have come to a complete stop before attempting to

perform maintenance.

Never work under equipment unless it is blocked securely. Never depend on hydraulic system to keep implement

in raised position.

Keep all persons away from operator control area while performing adjustments, service or maintenance.

Always use personal protection devices such as eye, hand and hearing protectors when performing any service

or maintenance.

Frequently check mower blades. They should be sharp, free of nicks and cracks and securely fastened.

Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit

is in a safe condition.

When completing a maintenance r service function, make sure all safety shields and devices are installed

before placing unit in service.

After servicing, be sure all tools, parts and service equipment are removed.

check to ensure all safety signs are installed and in good condition. (See Safety Sign section for location drawing).

Do not allow grease or oil to build up on any deck or platform.

Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement

parts must be used to restore your equipment to original speciﬁcations. The manufacturer will not claim

responsibility for use of unapproved parts and/or accessories and other damages as a result of their use.

If equipment has been altered in any way from original design, the manufacturer does not accept any liability

for injury or warranty.

A ﬁre extinguisher and ﬁrst aid kit should be kept readily accessible while performing maintenance on this

equipment.

MAINTENANCE SAFETY

BE-FMxRDG

Comply with state and local laws governing highway safety and movement of farm machinery on public roads.

The use of ﬂashing amber lights is acceptable in most localities. However, some localities prohibit their use.

Local laws should be checked for all highway lighting and marking requirements.

When driving the tractor and equipment on the road or highway under 20mph at night or during the day,

use ﬂashing amber warning lights and a slow moving vehicle (SMV) identiﬁcation emblem.

Always be sure the implement is in the proper position for transport.

Reduce speed when transporting mounted implements to avoid bouncing and momentary loss of steering control.

Plan your route to avoid heavy trac.

Do not drink and drive!

Watch for trac when operating near or crossing roadways.

Use extreme care and maintain minimum ground speed when transporting on hillside, over rough ground and

when operating close to ditches or fences. Be careful when turning sharp corners. Turn curves or go up or down

hills only at a low speed and at a gradual steering angle. Make certain that at least 20% of the tractor’s weight is

on the front wheels to maintain safe steerage. Slow down on rough or uneven surfaces and loose gravel.

Never allow riders on either tractor or mower.

Be a safe and courteous driver.

Always yield to oncoming trac in all situation like narrow bridges and intersections.

TRANSPORT SAFETY

BE-FMxRDG

SAFETY SIGN LOCATIONS

BE-FMxRDG

DANGER

THROWN OBJECT HAZARD

To prevent serious injury or death:

•Do not operate unless all guards

are installed and in good condition.

•Stop blade rotation if bystanders

come within several hundrHd feet.

DANGER

ROTATING BLADES - KEEP AWAY

To prevent serious injury or death when the engine is

running and the blades are rotating.

• Never allow riders, especially children, on tractor

or mower.

• Do not operate with bystanders in mowing area

'RQRWRSHUDWHZLWKGHÀHFWRUVJXDUGVUHPRYHG

• Do not place hands or feet under deck.

• Do not stand on or near implement at any time.

• Do not stand between tractor and implements.

• Operate only with tractor equipped ROPS and

seat belts.

WARNING

To prevent serious injury or death:

Si no lee ingles, pide ayuda a alguien que si lo lea para

que le traduzca las medidas de seguridad

• Read and understand Operator’s Manual before using.

• Review annually.

• Do not permit riders on the tractor or mower, inclduing children.

• Do not allow children to operate mower.

• Operate only with guards installed and in good working condition.

• Keep away from moving parts.

• Operate only with tractor equipped with ROPS and seat belts.

• Before mowing, clear derbis from mowing area.

• DO NOT operate in the raised position.

• Stop engine, lower mower, set brake and wait for all moving parts

to stop before dismounting.

• Support mower securely before working beneath unit.

• Transport with clean reflectors, SMV and working lights,

as required by local laws.

• Keep yourself, others and clothing away from the rotating PTO.

• Keep others away from area to be mowed to avoid injury

from flying objects.

• Do not stand between tractor and mower.

• Be careful on uneven terrain

• Decrease speed when turning.

• Do not exceed safe transport speed.

DANGER

ROTATING DRIVELINE HAZARD

KEEP AWAY!

To prevent serious injury or death from rotating driveline:

• Keep all guards in place when operating.

• Operate only at 540 RPM.

• Keeps hands, feet, clothing and hair away

from moving parts.

• Do not operate without driveline securely attached at

both ends.

• Do not operate without driveline shields that turn freely

on driveline.

SAFETY SIGN LOCATIONS

1 2

3 4

BE-FMxRDG

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AGRI EASE Rasenmäher Handbücher

AGRI EASE

AGRI EASE BE-AGL125F Anwendungshandbuch

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung