AIEMERY EFD Bedienungsanleitung
ATTENTION !!!
PLS ADD OIL BEFORE USE THE MACHINE
FLAIL MOWER
#EFD
1
FOREWORD
The purpose of this manual is to assist you in operating and maintaining your
Flail mower. Read it carefully before operating and maintaining the Flail mower,
it furnishes the specifications, construction, instructions and also the
maintenance. Some information may be general in nature due to unknown and
varying conditions. However, through experience and these instructions, you
should be able to develop operating procedures suitable to your particular
situation.
“Right” and “left” as used throughout this manual are determined by facing the
direction the machine will travel when in use.
Please kindly note that the contents of this operations manual may be a little
bit different from the Flail mower that you actually purchase. This is due to the
continuous improvement and development of the EFGCH series Flail mower,
however, the specifications and structure of the Flail mower shall be subject to
change without notice.
Thank you very much for purchasing our products. We cordially welcome all
the suggestions, advises and comments on our products from the users and
dealers so that we may make necessary improvements on our products
continuously to meet the requirements of every specific market.
We strived to make this operations manual as correct as possible. However,
we do not guarantee the accuracy or recentness of the information herein due
to having translated the manual to English. We assume no liability for errors or
omission.
Editor
November, 2004
2
CONTENTS
CHAPTER ⅠSAFETY INFORMATION................................................................ 3
1.1 Safety First......................................................................................................3
1.2 Safety Signs................................................................................................... 4
CHAPTER ⅡSPECIFICATIONS............................................................................5
2.1 Brief Introduction............................................................................................5
2.2 Specifications and Parameters for Flail Mower........................................ 5
CHAPTER ⅢOPERATION......................................................................................6
3.1 Checking Before Operating..........................................................................6
3.2 Adjusting the Height...................................................................................... 6
3.3 Regulating the Tension of Driving Belt....................................................... 7
3.4 Staring up........................................................................................................8
CHAPTER ⅣSERVICE AND MAINTENANCE....................................................9
4.1 Service.............................................................................................................9
4.2 Maintenance................................................................................................... 9
4.3 Storage..........................................................................................................10
4.4 Operation After Storage..............................................................................11
CHAPTER ⅤILLUSTRATED PARTS CATALOGUE.........................................12
5.1 Flail Mower Assembly................................................................................. 13
5.2 Gearbox Assembly...................................................................................... 16
5.3 Blade Axle and Transmission Parts..........................................................18
3
CHAPTER ⅠSAFETY INFORMATION
PLEASE NOTE
Make sure all potential operators of this equipment review this manual
and all safety messages contained within.
1.1 Safety First
Read this service manual before using the machine.
This safety alert symbol indicates important safety messages in this
manual. When you see this symbol, carefully read this message that
follows and be alert to the possibility of personal injury or death.
This machine is designed for pulverizing grass and short bramble, and shall be used in the
indicated purpose. You take the responsibility if the machine is used in any other
purposes.
For safety of personnel and good performance of the machine, you shall check the
performance of the machine and the tractor before starting the machine.
All persons and animals shall keep away the machine when you start it.
The operator shall not put on too loose clothes during operating the machine.
Do not touch the rotor when the machine rotates.
Keep away the machine when it moves.
When the tractor and the machine are moving on the road, always keep the machine off.
Before repairing the machine, stop all movable parts and the tractor, keep the key with
yourself.
Always keep the machine in a good state, if necessary, repair or change the defective
parts.
Don’t use the machine to transport personnel.
Don’t modify the machine.
Pay attention to the sharp and pointed parts during repairing the machine.
All protective parts shall be guaranteed to be in good state before starting the machine.
Don’t leave the tractor when moving the machine; and always take away the key of the
tractor with you.
The machine shall be operated in the recommended speed.
Don’t stay between the tractor and the machine.
4
Don’t start the machine in a closed place (due to the smoke from the tractor).
1.2 Safety Signs
1.2.1 Care of Safety Signs
1. Keep safety signs clean and legible at all times.
2. Replace safety signs that are missing or have become illegible.
3. If a component with a safety sign(s) affixed is replaced with a new part, make sure new
safety sign(s) are attached in the same locations as the replaced components.
4. Safety signs are available from your authorized Distributor or Dealer Parts Department or the
factory.
1.2.2 Safety Signs locations
The types of safety signs and locations on the equipment are shown in the illustrations
that follow. Good safety requires that you familiarize yourself with the various safety signs,
the type of warning and the area, or particular function related to that area, that requires
your SAFETY AWARENESS.
5
CHAPTER ⅡSPECIFICATIONS
2.1 Brief Introduction
EFGCH series Flail mower is designed for pulverizing grass and short bramble, and shall
be used in the indicated purpose.
The Flail mower consists of a rotating shaft with many blades attached to it. The blades
cut the grass while traveling over the working area. Rotational power to the shaft is
provided by the tractor PTO through the gearbox in the center of the machine.
The Flail mower attaches to the 3 point hitch on the tractor.
Fig. 2.1 Main components of the Flail mower
1. Blade axle 2. Blade axle cover 3. Combined fender 4.Supporting frame
5. Gearbox assembly 6. Suspension bracket 7. Transmission shaft 8. Belt wheel and belt
6
CHAPTER ⅢOPERATION
CAUTION: Be familiar with the machine before starting. Read this manual
carefully to learn how to operate the machine safely and how
to set it to provide maximum field efficiency.
3.1 Checking Before Operating
ATTENTION: Only use universal joint conforming to CE standard and
protect them properly.
Before operating the machine, the following areas should be checked off:
1. Pay attention to the warning stickers on each greasing point. Before starting the
machine, please make sure lubricate each grease point with grease or oil
according to requirement on the warning stickers.
2. Use only an agricultural tractor of horsepower within limits of the machine specified.
3. Check that the machine is properly attached to the tractor. Be sure retainers are used
on the mounting pins.
4. Be sure extra weights are mounted on the front of the tractor.
5. Check the oil level in the gearbox. Add as required.
6. Check that the tractor PTO shaft turns freely and that the machine driving shaft can
telescope easily.
7. Check the blades. Be sure they are not damaged or broken and swing freely in their
mount. Repair or replace as required.
8. Check and tighten the blade bolts.
9. Check for entangled material in all rotating parts. Remove this material.
10. Install and secure all guards, doors and covers before starting.
11. Before installing the universal joint, the tractor and the machine motor shall be
stopped and the key be taken away. The universal joints shall be installed in good
state, with proper protective parts.
12. The chain on the protective parts of the universal joint shall be guaranteed in good
condition, in case, automatic rotation occurs.
13. All other persons shall leave the ground before connecting the driving power from the
tractor. Keep the output of the tractor at 540 RPM.
14. Before cleaning, repairing and lubricating the machine, stop the motor and take away
the key with you.
15. When the universal joint is not connected with the tractor, they must be connected
again through the frame to protect the joint from damaging.
16. Don’t approach the machine when the machine runs.
3.2 Adjusting the Height
In order to conduct a precise work, the machine shall be operated according to the
recommended cutting height.
For saving fuel and power, and reducing the wear of the machine, the cutting height must
7
be regulated correctly.
When regulating the working height, loosen the screw (1), remove the screws (2) on both
sides; regulate the roller height (see following drawing); fix the parts on the set position.
The lowest hole is the highest working height; put the screws (2) into the set hole; tighten
screw (1) and screws (2).
3.3 Regulating the Tension of Driving Belt
ATTENTION: The machine shall always stand still for regulating the
tension.
Remove the driving belt
cover.
Loosen screws 1. 2. 3. 4.
Tighten the driving belt
with screw 5.
Tighten the screws 1. 2.
3. 4.
Put back the driving belt
cover.
The recommended moving forward speed is 1.5
km/h, according to the grass height, thickness
and working condition.
The driving belts are tightened by hand at the
regulating point B up to the correct tension.
Tighten all screws after regulating.
The driving belts shall be replaced when they are
not in a good condition.
8
3.4 Staring up
Before starting the machine, control and adjust the following items:
Tension of trapezoidal driving belt.
Oil level of gear.
Point of lubrication
All bolts, nuts and screws.
Working
Position Moving
Position
In order to keep the machine stable, install the supporting frame on the machine when the
machine is stopped (see above drawing).
ATTENTION: When transferring the moving state of the machine to the
working state, do not stand between the machine and the
tractor.
The machine coupling is equipped with 3 pins so that the machine can be coupled with all
tractors with universal coupling with 3 pins. Each telescopic pole on the machine can be
adjusted properly according to the type of the tractor. Keep the Flail mower away the
tractor with a certain distance. The universal joint shall be tense and the largest distance
in the closed state shall be 5/10 cm.
Moving the lifting arm, and putting it between axes, insert the joint pins and fix them with
pins. Fix the lifting arm with chain and tensioning device so as to prevent lateral
movement of the machine. Connect the universal joint to the PTO shaft of the tractor on
the side of the tractor. In any event, it cannot produce a collision in any position. While
connecting 3 points, pay attention to that the PTO shaft of the tractor shall be parallel with
the ground. It is very important to keep the machine driving axle and the PTO shaft of the
tractor in parallel.
The machine shall be lifted from the ground before moving the machine.
9
CHAPTER ⅣSERVICE AND MAINTENANCE
4.1 Service
4.1.1 FLUIDS AND LUBRICANTS
1. Grease:
Use multi-purpose lithium based grease.
2. Gear Box Oil:
Use N46 drive &hydraulic dual-purpose oil or equivalent for all operating conditions.
Each Gearbox Capacity: 0.85 liter
3. Storing Lubricants:
Your machine can operate at top efficiency only if clean lubricants are used. Use clean
containers to handle all lubricants. Store them in an area protected from dust,
moisture and other contaminants.
4.1.2 GREASING
Use a hand-held grease gun for all greasing.
Wipe grease nipple with a clean cloth before greasing, to avoid injecting dirt and grit.
Replace and repair broken nipple immediately.
If nipples will not take grease, remove and clean thoroughly. Also clean lubricant
passageway. Replace nipple if necessary.
4.2 Maintenance
ATTENTION: All maintenance, repairing, cleaning and lubricating shall
be conducted when the tractor and motor are stopped and
the key is taken away.
By following a careful service and maintenance program for your machine, you will enjoy
many years of trouble-free operation.
The period recommended is based on normal operating conditions. Severe or unusual
conditions may require more frequent maintenance.
4.2.1 8 HOURS OR DAILY MAINTENANCE
Check and screw all nuts and bolts in connection parts.
Check the blade and fixing parts every day and replace the damaged parts if they are
found damaged. Don’t install damaged, worn and unbalanced blade. New sleeve
shall be used to replace the worn fixing parts on the blade.
NOTE:
The operator shall put on gloves and use suitable tools before changing blade.
Check the oil in gearbox. Fill them up to line if it’s necessary.
Press butter in each oil nipple three to five times.
Clean the implement; take away all grass and mud.
Inhaltsverzeichnis
Beliebte Rasenmäher Handbücher anderer Marken
TALEN TOOLS
TALEN TOOLS AVR HGM30 Bedienungsanleitung
DEWEZE
DEWEZE ATM-725 Bedienungsanleitung
Weed Eater
Weed Eater 180083 Bedienungsanleitung
Husqvarna
Husqvarna Poulan Pro PP185A42 Bedienungsanleitung
Better Outdoor Products
Better Outdoor Products Quick Series Bedienungsanleitung
Cub Cadet
Cub Cadet 23HP Z-Force 60 Betriebsanleitung
