Aim SmartyCam HD Bedienungsanleitung
Configuring
1
www.aim-sportline.com Release 1.01 – November 21st 2018
1 – SmartyCam and AiM devices
Question:
How can I connect my SmartyCam HD/GP HD with AiM devices and configure both?
Answer:
Those AiM devices that support SmartyCam, in addition to the physical connection with the proper
cables need, together with SmartyCam, a software setup. The table below shows which software you
need to install on your PC:
•SoloDL RS2
•MXL RS2
•EVO4 RS2
•ECU Bridge RS2
•Solo 2 DL RS3
•MXL2 RS3
•MXS 1.2/MXS Strada 1.2 RS3
•MXG 1.2/MXG 1.2 Strada RS3
•MXP/MXP Strada RS3
•MXm RS3
•EVO4S RS3
•EVO5 RS3
•SmartyCam RS3
To make the communication between SmartyCam and AiM devices possible, you need to:
•physically connect the devices
•set AiM devices up using the proper software
•configure SmartyCam with RS3
Configuring
2
www.aim-sportline.com Release 1.01 – November 21st 2018
1.1 – Physical connection
To physically connect the devices, use SmartyCam CAN cable; available versions are:
•SmartyCam CAN cable: length 2m: V02566070
•SmartyCam CAN cable: length 4m V02566060
Each AiM device is equipped with a connector or a cable labelled “EXP” that is to be connected to
SmartyCam “EXT” connector:
•SoloDL/Solo 2 DL: connect SmartyCam CAN cable to the 5 pins connector placed under the
device
The 7 pins connector is used to connect with the vehicle ECU (via CAN, K-Line or RS232) and the
external power source
•EVO4/4S: connect SmartyCam CAN cable to the connector labelled “Exp”
•EVO5: connect SmartyCam CAN cable to the cable labelled “EXP” of 37 pins connector harness
included in the kit
•MXL2, MXS 1.2, MXG1.2/MXP: connect SmartyCam CAN cable to the cable labelled “EXP” of 37
pins connector harness included in the kit
•MXS 1.2 Strada/MXG 1.2 Strada/MXP Strada: connect SmartyCam CAN cable to the cable
labelled “EXP” of 14 pins connector harness included in the kit
•MXL Strada/Pista: connect SmartyCam CAN cable to the 5 pins connector placed rear right of the
device
•MXL Pro05: connect SmartyCam CAN cable to the cable labelled “EXP” of 22 pins connector
harness included in the kit
•ECU Bridge: connect the camera CAN cable to 5 pins connector of the device.
If you need to connect more expansions we suggest to use a Data Hub – AiM CAN connections
multiplier – available in different versions with different part numbers:
•two ways Data Hub with 40 cm cable: X08HB2GK0
•four ways Data Hub with 40 cm cable: X08HUB010
•four ways Data Hub with 150 cm cable: X08HUB150
Configuring
3
www.aim-sportline.com Release 1.01 – November 21st 2018
1.2 – RS2 configuration
MXL, SoloDL, EVO4 and ECU Bridge are only configurable using RS2. Latest updates are always
downloadable from Download Area -> Software of www.aim-sportline.com.
Proceed as follows:
•run RS2
•connect your device to the PC and press “Device Configuration”
•select your device and choose the configuration to be modified or create a new one
•complete the device setup
•click “SmartyCam Functions Settings”, in the page top keyboard: a table appears where you can
associate different functions (left column) to each channel (right column); the channels list is
filtered according to the functions set; user can unlock the filtering and have free choice checking
“Enable Channels for all Functions” box
•once the functions associated to the channels click “OK” and then “Transmit” to transmit the
configuration to the device
Configuring
4
www.aim-sportline.com Release 1.01 – November 21st 2018
1.3 – RS3 configuration
Solo 2 DL, MXL2, MXG 1.2, MXG 1.2 Strada, MXS 1.2, MXS 1.2 Strada, MXP, MXP Strada, MXm, EVO4S ed
EVO5 are only configurable with RS3. Latest updates are always downloadable from Download Area ->
Software of www.aim-sportline.com.
Proceed as follows:
•run RS3
•connect your device to the PC and enter “Configurations” page
•select the configuration you need to modify or create a new one
•enter “SmartyCam Stream” layer: a table appears where you can associate different functions (left
column) to each channel (right column); the channels list is filtered according to function set; user
can unlock the filtering and have free choice checking “Enable Channels for all Functions”
•once the functions associated to the channels click “Transmit” to transmit the configuration to the
device
Configuring
5
www.aim-sportline.com Release 1.01 – November 21st 2018
1.4 – SmartyCam configuration with RS3
To setup SmartyCam HD/GP HD you need to use RS3 software (RS2 does not support cameras).
Proceed as follows:
•run RS3
•connect SmartyCam to the PC using the mini USB cable you find in the kit
•enter “Configuration” page and select the configuration to modify or create a new one; to create a
new configuration press “New” button, select “SmartyCam HD” among the available devices, fill in
the configuration name and press “OK” as shown here below.
Configuring
6
www.aim-sportline.com Release 1.01 – November 21st 2018
The software opens SmartyCam configuration page.
•right side of the window shows many overlay sets that can be dragged and dropped into the left
main window
•bottom left of the page each overlay properties appear in specific tabs that need to be setup
•once SmartyCam setup click “Save” in keyboard placed on top of overlay layers, go back to
configurations page and transmit the configuration to SmartyCam.
Andere Handbücher für SmartyCam HD
4
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
