Air Lift Performance 3S Bedienungsanleitung
PATENTED
Air Lift
Performance
3S
®
Control System
For maximum effectiveness and safety,
please read these instructions completely
before operating.
Failure to read these instructions can result in an
incorrect installation.
USER GUIDE
AD-955 • (011807) • ERN 8639
®
TABLE OF CONTENTS
Introduction ........................... 3
Important Safety Notices .......................... 3
Smartphone App for 3S ....................4
Download the App for the Best #lifeonair .............. 4
Bluetooth Pairing ................................ 4
App Navigation.................................. 5
Bluetooh Wakeup ................................ 5
Changing Presets ................................ 6
Setting User-Defined Buttons ....................... 6
ALP3 Display for 3S
.......................7
Quick Reference Guide............................ 7
Getting Started.................................. 8
Display ........................................ 9
About ........................................ 10
Additional Information ............................ 11
3S Display .................................... 11
APV2 for 3S. . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Operating the System............................ 12
Manual Mode .................................. 12
Backlight Setting ............................... 13
APV2 Display .................................. 13
Manual Switch Box ......................14
Troubleshooting Guide....................15
FCC and Industry Canada
Information to User ......................15
3
AD-955
3S User Guide
Introduction
The Air Lift Performance 3S control system is available with four controller
options: ALP3 display, AutoPilot V2, smartphone app only and for use
with an aftermarket controller such as an AVS switch box. No matter
which version is purchased, the 3S system will work with the free Air Lift
Performance smartphone app for Apple iOS or Android. The system is not
directly compatible with existing ALP3 and APV2 displays.
Read the entire user guide before using or servicing. The information
includes display options and functions, and diagnostic troubleshooting.
Air Lift Company reserves the right to make changes and improvements to
its Air Lift Performance products and publications at any time. For the latest
version of this user guide, contact Air Lift Company at (800) 248-0892 or
visit www.airliftperformance.com.
IMPORTANT SAFETY NOTICES
THIS SYSTEM IS COMPLETELY MANUAL.
IT DOES NOT HAVE SAFETY FEATURES TO
PREVENT THE VEHICLE FROM ADJUSTING
BELOW A SAFE RIDE HEIGHT.
ONLY USE THE AIR LIFT PERFORMANCE 3 APP
ON A MOBILE DEVICE WHEN THE VEHICLE IS IN
A CLEAR LINE OF SIGHT. TO AVOID THE RISK OF
SERIOUS INJURY OR HARM, VERIFY THAT NO PERSON OR THING IS
NEAR OR IN THE WAY OF THE VEHICLE’S PATH OF TRAVEL WHILE
CYCLING THE SUSPENSION.
FLOOR JACKS CAN BE DANGEROUS.
WHENEVER USING A FLOOR JACK, MAKE
SURE IT IS RATED FOR THE LOAD IT IS LIFTING.
CHECK THE VEHICLE OWNER’S MANUAL FOR INFORMATION ABOUT
WHERE TO PLACE THE JACK. BEFORE RAISING THE VEHICLE,
PLACE WHEEL CHOCKS IN FRONT AND BEHIND THE WHEELS TO
PREVENT THEM FROM ROLLING. ALWAYS USE JACK STANDS TO
SUPPORT THE VEHICLE. NEVER GET UNDER OR PLACE ANY BODY
PARTS UNDER A VEHICLE THAT IS SOLELY SUPPORTED BY THE
JACK.
WARNING
WARNING
WARNING
4AD-955
3S User Guide
Smartphone App for 3S
BLUETOOTH PAIRING
The 3S manifold will
enter pairing mode for
5 minutes after doing
one of three things:
• the main fuse is
installed
• the battery is
connected
• the connector
is plugged into the
manifold
Once a device is
paired, the manifold
will exit pairing mode.
Only one device
can be paired to the
manifold at a time.
Once the manifold is
in pairing mode, go
to the devices menu
in the 3S App and select the 3S manifold under the devices found list.
iOS Android
DOWNLOAD THE APP
FOR THE BEST #LIFEONAIR
The Air Lift Performance
3S mobile app allows for
full integration of your
new 3S control system
on compatible mobile
devices. Simply download
the FREE app to take full control of the
system.
For iPhone: air-lift.co/apple3s
For Android: air-lift.co/android3s
Users can also search “Air Lift Performance”
in either the Apple App Store or Google Play.
5
AD-955
3S User Guide
iOS
Manually increase
and decrease front
right air spring
pressure.
Manually increase
and decrease
front left air spring
pressure.
Preset High
(Up Button)*
Preset Ride
(Middle Button)*
Preset Low
(Down Button)*
User-defined
Button
(See Page 7
All-Up Button)
Manually increase
and decrease rear
right air spring
pressure.
User-defined
Button
(See Page 7
All-Down Button)*
Manually increase
and decrease
rear left air spring
pressure.
Double tap to
activate presets
APP NAVIGATION
* Presets and user-defined buttons are established in the ALP3 app (see page 7)
BLUETOOTH WAKEUP
The manifold supports Bluetooth wakeup of the manifold. This allows
operation of the manifold using a mobile device with the ignition off. The
manifold will power down after one minute of inactivity.
6AD-955
3S User Guide
CHANGING PRESETS
1. Click on the gear in
the upper right of
the screen to enter
settings.
2. Select “Operation,”
then “Preset,”
choose the button to
change, make sure
the button is set to
“On” and choose
the function (dump
or fill).
3. Use the sliders to set
the valve open time.
Users can also click
on the seconds value
to open a pop-up
to enter the desired
value. 3S includes three programmable, stored presets which allow
you to make quick system adjustments using valve open times. This
feature can only be set up using the app but the presets can be
triggered using the app or ALP3 display.
Android
iOS
SETTING USER-DEFINED BUTTONS
The top and bottom
user-defined buttons are
factory set for “All-Up”
and “All-Down.” Both
buttons can be set for
all, front or rear.
AndroidiOS
7
AD-955
3S User Guide
Manually increase
and decrease front
right air spring
pressure.
Manually increase
and decrease
front left air spring
pressure.
Preset High
(Up Button)*
Preset Ride
(Middle Button)*
Preset Low
(Down Button)*
QUICK REFERENCE GUIDE
Main Menu
Screen Sub-Menu Data Default
Display
Brightness Level 1-10 Level 7
Brightness Sleeping Level 1-10 Level 4
Sleep Time 5-60 Sec 10 Sec
All-Up Button
All-Up
All-UpFront-Up
Rear-Up
All-Down Button
All-Down
All-DownFront-Down
Rear-Down
ALP3 Display for 3S
The ALP3 display for 3S is the basic function version of Air Lift
Performance’s award-winning top-line air management system.
* Presets and user-defined buttons are established in the ALP3 app (see table below)
User-defined
Button
(See Page 10
All-Up Button)
Double tap to
activate presets
Manually increase
and decrease rear
right air spring
pressure.
User-defined
Button
(See Page 10
All-Down Button)*
Manually increase
and decrease
rear left air spring
pressure.
8AD-955
3S User Guide
GETTING STARTED
1. To get to the main menu screen, push the
middle (preset ride) button simultaneously
with either the up (preset high) button or
down (preset low) button.
2. All other settings and parameters will be
detailed in the following pages to ensure
the system is set up accurately.
3. Use the preset low and preset high buttons
to scroll.
4. Presets can only be set on the ALP3
smartphone app (see page 6).
9
AD-955
3S User Guide
DISPLAY
Brightness
Set the brightness for the display while in use.
1. Level 1-10
2. Use the up and down buttons to increase
or decrease luminosity in 10% increments.
3. Level 7 (default)
Brightness Sleeping
Set the brightness for the display after it goes
into sleep mode.
1. Level 1-10
2. Use the up and down buttons to increase
or decrease luminosity in 10% increments.
3. Level 4 (default)
Sleep Time
Set the amount of time it takes to revert back
to the main screen and for the display to go to
sleep.
1. 5-60 seconds.
2. Use the up and down buttons to increase
or decrease time in 1-second increments.
3. 10 seconds (default)
All-up Button
Set function for the all-up button.
1. All up (default)
2. Front up
3. Rear up
All-down Button
Set function for the all-down button.
1. All down (default)
2. Front down
3. Rear down
10 AD-955
3S User Guide
ABOUT
Select this option to see what version of
software is running on the system, product
serial number and Bluetooth identification
address.
Users may need to provide this information
when calling Air Lift Company customer
service.
Firmware on the 3S display can be updated for
use with the 3H system.
Inhaltsverzeichnis
Andere Air Lift Performance Steuerungssystem Handbücher
