Aire Sky Parlor Bedienungsanleitung
INSTRUCTION MANUAL WARRANTY CERTIFICATE
READ AND SAVE ALL INSTRUCTIONS
Sky Parlor
2
This product is protected by United States Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent,
Trademark and/or Copyright laws.
1151 W. Bradford Court, Corona, CA 92882 For Customer Assistance Call: 1-800-307-3267
3
The Aire warranty is for one (1) year from the date of purchase from an authorized Aire dealer. This warranty is only
valid to the original purchaser or user against all defects in material and workmanship (light bulbs excluded) for one (1)
full year. Additionally, Aire warrants the motor only for the lifetime of the Aire ceiling fan (excluding wall controls and
electrical components), to the original purchaser or user.
To obtain warranty service during the warranty period, the purchaser should return the fan with the original sales
receipt to the original place of purchase. Replacement is subject to availability of the same model. This is a limited
warranty; the original purchaser or user is responsible for the cost of removal and re-installation of repaired or
replacement product. Outdoor finishes are specifically excluded from the terms of this warranty since they are subject
to environmental and maintenance damages beyond our control.
Fan warranty registration should be mailed as addressed on the warranty card.
• The warranty is void with the use of any non-Aire electrical devices; e.g., wall controls or electrical dimmer switches,
etc.
• The warranty is void once the original purchaser or user ceases to own the fan or the fan is moved from its original
point of installation.
• The warranty is void with the use of any hanger bracket (non-Aire or non-fan specific) other than the hanger bracket
supplied in the box.
• The warranty is void if installed in an environment other than its intended use (Indoor fans installed outdoors or in a
covered outdoor patio area, or subjected to environmental conditions: salt air, humidity, direct sun exposure, etc.).
Outdoor finfshes are specifically excluded from the terms of this warranty since they are subject to environmental
and maintenance damages beyond our control.
WARRANTY SERVICE INFORMATION
WARRANTY
Date Purchased Store Purchased Model Number
04613
Serial Number
CONTENTS
SAFETY RULES............................................................................
PACKAGE CONTENTS..................................................................
INSTALLING THE FAN..................................................................
HANGING THE FAN......................................................................
ELECTRICAL CONNECTIONS........................................................
FINISHING THE INSTALLATION....................................................
ATTACHING THE FAN BLADES....................................................
INSTALLING THE MOUNTING PLATE.......................................
INSTALLING THE LIGHT KIT....................................................
INSTALLING THE GLASS SHADE............................................
OPERATING THE REMOTE CONTROL......................................
CARE OF YOUR FAN...............................................................
TROUBLESHOOTING..............................................................
SPECIFICATIONS...................................................................
4
5
6
7
8
9
10
10
11
12
13
15
16
17
4
SAFETY RULES
1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before
beginning.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes.
Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35
lbs. Use only UL-listed outlet boxes marked “FOR FAN SUPPORT.”
4. The fan must be mounted with a minimum of 7 ft. clearance from the trailing edge of the blades to the floor.
5. Avoid placing objects in the path of the blades.
6. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
7. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will
be suitable for most cleaning.
8. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the
outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
9. All setscrews must be checked and retightened where necessary before installation.
10. Turn the fan off and wait for the blades to stop completely before performing any maintenance or cleaning.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER PERSONAL INJURY, MOUNT FAN ONLY ON AN OUTLET BOX OR
SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS AND USE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING
FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN
IF IN DOUBT.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING, BALANCING THE
BLADES OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
TO REDUCE THE RISK OF FIRE OF ELECTRONIC SHOCK, THIS FAN ONLY CAN USE AL-170-1101SPS SOLID-STATE SPEED
CONTROL WITH DL-6102T REMOTE CONTROL ONLY.
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible
conditions and situations that may occur. It must be understood that common sense, caution and care are factors which
cannot be built into this product. These factors must be supplied by the person (s) installing, caring for and operating
the unit.
5
13. 12V MN21/A23 battery
14. Balancing kit
Mounting hardware:
#10 x 1.5" Wood screws (2 PCs.)
#8 x 3/4" Machine screws (2 PCs.)
Lock washers (2 PCs.)
4mm Star washers (2 PCs.)
Wire nuts (3 PCs. )
Washers (2 PCs.)
Blade attachment hardware:
3/16" x 7.5mm Screws and fiber washers (16 PCs.)
Blade holder attachment hardware:
1/4" x 1/2" Screws with lock washers (11 PCs.)
1. Fan blades (5)
2. Blade holders (5 )
3. Hanger bracket
4. Canopy
5. Canopy cover
6. Downrod assembly
7. Coupling cover
8. Fan motor/housing assembly
9. Mounting plate
10. 20 Watt LED light kit
11. Glass Shade
12. Remote control with holder and 2
mounting screws
PACKAGE CONTENTS
Unpack your fan and check the contents. You should have the following items:
1
2
4
3
5
7
9
8
10
11
12
13
14
6
A.
B.
C.
B
A
C
1
2
34
5
6
6
INSTALLING THE FAN
Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape.
MOUNTING OPTIONS
If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses
or turning off circuit breakers.
Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet
box and its support must be able to fully support the moving weight of the fan (at least 50 lbs.). Use a UL Listed metal
outlet box. Do not use a plastic outlet box.
Figure 1, 2 and 3 are examples of different ways to mount the outlet box.
Note: You may need a longer downrod to maintain proper blade clearance when installing on a steep, sloped ceiling.
Longer downrods are available from your Aire dealer.
To hang your fan where there is an existing fixture but no ceiling joist, you may need to install a hanger bar as shown
in Fig. 4 (available at your Aire dealer).
CEILING
JOIST
FIG. 1
CROSS
BRACE
CEILING
JOIST
CEILING
jOIST
OUTLET BOX
OUTLET BOX
FIG. 2
PARALLEL WOOD BRACE
(MIN. 2" THICK)
OUTLET
BOX
CEILING JOIST OR
CROSS BRACE
FIG. 3 FIG. 4
ANGLED CEILING
MAXIMUM 18° ANGLE PROVIDE
STRONG
SUPPORT
RECESSED
OUTLET BOX
HANGER
OPENING
MUST BE
FACING
UPSIDE
HANGER BAR
(OPTIONAL)
HANGER
BRACKET
7
HANGING THE FAN
WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been
provided for your safety and the proper installation of your new ceiling fan. The use of other parts, hardware or
components not supplied by Aire with the fan will void the Aire Warranty.
REMEMBER to turn off the power. Follow the steps below to hang your fan properly:
Step 1. Secure the Hanger Bracket to the ceiling outlet box using the screws provided with your outlet box in
conjunction. (Fig. 5)
Step 2. Loosen the two Set Screws and remove the Hitch Pin and Lock Pin from the coupling located on the top of the
Motor Assembly. (Fig. 6)
Step 3. Remove the Hanger Ball from the Downrod Assembly by loosening the Set Screw and removing the Cross Pin.
(Fig. 7)
Step 4. Carefully feed fan wires up through the downrod. (Fig. 8) Thread Downrod into the Coupling until the holes are
lined up and secure with the Lock Pin and Hitch Pin previously removed, tighten Set Screws. (Fig. 9)
Step 5. Slip coupling cover, canopy cover and canopy onto downrod. (Fig. 9) Carefully reinstall hanger ball onto rod being
sure that cross pin is in correct position, set screws are tighten and wires are not twisted.
Step 6. Lift the Motor Assembly and place the Hanger Ball into the Hanger Bracket. Rotate the Motor Assembly as needed
until the check groove from the Hanger Ball rests firmly over the registration tab from the Hanger Bracket. (Fig. 10)
HITCH
PIN LOCK
PIN
SET SCREWS
FIG. 6
CROSS PIN
HANGER
BALL
DOWNROD
SET SCREW
FIG. 7
DOWNROD
SUPPLY
WIRES
FIG. 8
FIG. 10
REGISTRATION
SLOT
FIG. 5
OUTLET BOX
HANGER BRACKET
FIG. 9
DOWNROD
CANOPY
HITCH PIN
LOCK PIN
COUPLING COVER
SET SCREWS
CANOPY
COVER
8
ELECTRICAL CONNECTIONS
WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before
wiring.
NOTE: The Aire Control® System for this DC motor fans is equipped with a learning frequency function which has 32
code combinations to prevent potential interference from other remote units. The frequency on your Receiver and
Transmitter units have been preset at the factory. (Fig. 11) No frequency change is necessary, should you desire to
install another Minka Aire DC motor fan within the same home or area with a separate frequency code please see the
"frequency interference" troubleshooting section of this instruction manual to learn how to change the frequency.
The “D (DIMMER)” selection is the light dimmable selection and is to be used with all bulbs except for CFL bulbs. The
“ON (ON/OFF)” selection is the light on only (no dimming function) and is to be used with CFL bulbs as CFL bulbs cannot
be dimmed properly.
Step 1. Motor to House Supply Wires Electrical Connections: Connect the WHITE wire (Neutral) from the outlet box to the
WHITE wire marked "AC in N" from the motor. Connect the BLACK wire (Hot) from the outlet box to the BLACK wire
marked "AC in L" from the motor. Secure all wire connections with the plastic wire nuts provided. (Fig. 12)
Step 2. If your outlet box has a GROUND wire (Green or Bare Copper) connect this wire to the Hanger Ball and Hanger
Bracket Ground wires. If your outlet box does not have a Ground Wire, then connect the Hanger Ball and Hanger Bracket
Ground Wires together. Secure wire connection with the plastic wire nut provided. (Fig. 12)
After all splices are made, check to make sure there are no loose strands. As an additional precaution we suggest to
secure the plastic wire connectors to the wires with electrical tape.
FIG. 11 FIG. 12
FREQUENCY
WHITE (NEUTRAL)
WHITE ("AC IN N")
GREEN OR BARE
COPPER (GROUND)
GROUND
(GREEN)
(CONNECT TO
GROUND WIRE
ON HANGER
BRACKE IF NO
HOUSE GROUND
WIRE EXISTS.)
BLACK (HOT)
BLACK ("AC IN L")
9
FINISHING THE INSTALLATION
Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the
screw head.
Step 2. Slide the canopy up towards the hanger bracket and place the key hole on the canopy over the screw on the
hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 13)
Step 3. Align the circular hole on canopy with the remaining hole on the hanger bracket, secure by tightening the two
set screws.
Note: Adjust the canopy screws as necessary until the canopy and canopy cover are snug.
FIG. 13
OUTLET BOX
HANGER
BRACKET
HANGER
BALL
CANOPY
CANOPY
COVER
10
ATTACHING THE FAN BLADES
Step 1. Attach the fan blades to the blade holders using the screws and fiber washers provided, tighten screws and fiber
washers securely. Repeat process with other blades. (Fig. 14)
Step 2. Align motor holes to blade holders and secure with screws and lock washers provided, tighten screws securely.
Repeat process with other blades. (Fig. 15)
FIG. 16
INSTALLING THE MOUNTING PLATE
FIG. 14
FAN BLADE
BLADE HOLDERS
SCREWS AND FIBER WASHERS
FIG. 15
Step 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove)
Step 2. Place the key holes from the mounting plate over the 2 screws previously loosened from the mounting ring, turn
mounting plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously
loosened and the one previously removed. (Fig. 16)
MOTOR
SCREWS
BLADE
HOLDER
ASSEMBLY
MOUNTING
PLATE
SCREWS
MOUNTING RING
Inhaltsverzeichnis
Andere Aire Lüfter Handbücher
