AirLink Communications Raven Bedienungsanleitung

Cingular EDGE/GPRS Raven

Quick Start Guide

Setup Wizard and Activation Instructions

AirLink Communications, Inc.

September 9, 2005

version 2.01

Information in this document is subject to change without notice

WARNING

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least

20 cm from all persons and must not be co-located or operating in conjunction with any other antenna

or transmitter.

Important Notice

Because of the nature of wireless communications, transmission and reception of data can never be guaranteed.

Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data

are rare when wireless devices such as the AirLink Communications modem are used in a normal manner with a

well-constructed network, the AirLink modem should not be used in situations where failure to transmit or

receive data could result in damage of any kind to the user or any other party, including but not limited to

personal injury, death, or loss of property. AirLink Communications, Inc., accepts no responsibility for damages

of any kind resulting from delays or errors in data transmitted or received using the AirLink Communications

modem, or for failure of the AirLink Communications modem to transmit or receive such data.

Safety and Hazards

Do not operate the AirLink Communications modem in areas where blasting is in progress, where explosive

atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may

be susceptible to any form of radio interference. In such areas, the AirLink Communications modem MUST BE

POWERED OFF. The AirLink Communications modem can transmit signals that could interfere with this

equipment. Do not operate the AirLink Communications modem in any aircraft, whether the aircraft is on the

ground or in flight. In aircraft, the AirLink Communications modem MUST BE POWERED OFF. When

operating, the AirLink Communications modem can transmit signals that could interfere with various on board

systems. The driver or operator of any vehicle should not operate the AirLink Communications modem while in

control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In

some states and provinces, operating such communications devices while in control of a vehicle is an offence.

Limitation of Liability

The information in this manual is subject to change without notice and does not represent a commitment on the

part of AirLink Communications, Inc. AIRLINK COMMUNICATIONS, INC. SPECIFICALLY DISCLAIMS

LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL,

CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS

OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR

INABILITY TO USE ANY AIRLINK COMMUNICATIONS, INC. PRODUCT, EVEN IF AIRLINK

COMMUNICATIONS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY

ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.

9/9/05 page 3 AirLink Communications, Inc

Cingular EDGE/GPRS Raven Quick Start

The Quick Start Guide details using the Setup Wizard only for the initial setup and any configuration

necessary to register your AirLink modem online with Cingular. For additional modem configuration

options, please refer to the Cingular EDGE/GPRS Raven User Guide.

Starting Setup Wizard

Install the Setup Wizard from the CD that came with your modem or you can download the latest

version from the AirLink website: http://www.airlink.com. The installation file for the Cingular

Setup Wizard is in the Support section under Modem Utilities.

1. Connect the modem to your computer using a serial cable.

2 Connect the power adapter and antenna to your modem.

3. Run the Setup Wizard from the Windows Start menu.

Start>All Programs>AirLink Communications>Setup Wizard>Setup Wizard

Note: The Setup Wizard requires Microsoft Windows 98 (with .Net), Microsoft Windows

2000, Microsoft Windows XP, or later.

Update Firmware: Check the AirLink servers for the latest

modem firmware.

Setup APN: Choose the Access Point you will be using with

your modem.

Test Modem Setup: Verify the modem is properly configured

and connecting on ‘s network.

Setup a DUN Connection: Creates a Dial-Up Networking

entry for local connection. This part of the setup is only

needed if you will be using the modem to connect directly from

a computer to the Internet or other network.

Select Connected to a Serial Port and

select the port from the drop down menu.

Check Auto Detect Port Settings.

The Setup Wizard will establish a connection

to your modem and detect the model. The

window should show the details for your

modem. If the incorrect modem is displayed,

press the Reset Button on your modem.

Cingular Raven Quick Start Guide v.2.01

AirLink Communications, Inc page 4 9/9/05

Update Firmware

AirLink frequently releases updates to the firmware for

your modem. These updates can include new features

as well as bug fixes. To make sure your modem is at

optimal performance, it is recommended to Check for

Updates and Update Now.

Note: While checking for updates, the Setup Wizard

needs to use the Internet connection on your computer

to connect to the AirLink server. Your modem is not

connected to the wireless network for this process.

Setup APN

The modem needs to be configured to communicate to a

specific Access Point.

•Internet and Proxy do not have additional

settings.

•ISP and WAP require additional settings. Consult with

Cingular about these settings.

Test Modem Setup

Using the Cingular cellular network, your modem’s

connection to the Internet is tested.

Green checks in all five boxes indicate the tests were

successful and your modem is functioning properly.

At this point your modem is configured and activated to

work on the Cingular network.

Cingular Raven Quick Start Guide v.2.01

9/9/05 page 5 AirLink Communications, Inc

Working Modem

In this example of the modem's lights, you can see how a modem will look when it is registered on the

network and working.

The RSSI light shows the strength of the signal

and may be solid (strong) or flashing (weaker).

The Tx (transmit) and Rx (receive) lights will

flash as data is transferred to and from the modem

on the network.

Troubleshooting

If Test Modem Settings shows the status of your modem is “No Service”, “No Carrier”, “Network

Negotiation Failed”, or “Network Authentication Failed” or the Reg light on the modem is not lit,

double-check your device activation information and return to the Access Point Name steps to

reconfigure your modem.

Setup a DUN Connection

Dial-up Networking (DUN) allows a computer or other device to use an AirLink modem to connect to

the Internet or private network just like an analog modem using a standard phone line. The Setup

Wizard will install a driver for the modem and set up the connection between your computer and the

modem. You will need to have administrator access on the computer for this section of the

installation.

If you already have other modems installed on your

computer, they will be listed on the AirLink Modem

Installation screen. If you have other modems installed

on your computer using the same serial port, they may

conflict. As long as you do not intend to use them, you

can Remove other modems using this menu.

Select Install to begin adding the driver for the AirLink

modem to your computer.The COM port and speed

should match your modem (the default settings will be

pre-entered). Select Next to begin the modem driver

installation. You will see a confirmation box from

Microsoft Windows to specify you wish to install this driver on your computer. Select Continue

Anyway to install the driver.

When the driver is installed, you will return to the AirLink Modem Installation screen. The

AirLink modem should now be listed (in addition to any other modem installed).

Cingular Raven Quick Start Guide v.2.01

AirLink Communications, Inc page 6 9/9/05

Select Next to begin installing the DUN connection.

If you already have a DUN connection installed for a

different modem, it will be listed on the Dial-up

Networking Connection screen.

Select Add to create a new connection for the AirLink

modem.

From the drop down menu, select the AirLink modem.

The defaults for the phone number, user name and

password will already be entered. Select Next to begin

the install.

At the completion of the DUN installation, you will

return to the Dial-up Networking Connection screen. The AirLink modem should now be listed as

a connection.

Your modem is now ready to be used as a DUN device for any applications on your computer needing

a network connection. If you have DUN installed for more than one modem, you will need to specify

in applications using DUN which modem you wish to use. Unless it is the only DUN, your AirLink

modem may not be the one your computer sees as a default.

Hardware Installation

Your AirLink modem should be mounted in a

position that allows easy access for the cables so

they are not bent or constricted. The LEDs on the

front panel should be visible for ease of operational

verification. In addition, you should ensure that

there is adequate airflow around the modem. The

exterior of the case should also be grounded.

You can mount the modem with an optional

mounting kit designed to “lock” the modem into

place. A zip tie can be used with the bracket for

installations where the modem needs to be secured

against sudden and abrupt movement (such as in

an automobile). If you are using a zip tie with the

bracket, run it through the side notches to secure

the modem.

Shown is the Raven with a dipole antenna.

Cingular Raven Quick Start Guide v.2.01

9/9/05 page 7 AirLink Communications, Inc

Your modem can be used with either DC (available in most automobiles) or 110 AC (standard US

wall power) with the appropriate power adapter.

Your modem will work with most standard cellular antennas with a TNC connector and rated to work

with EDGE/GPRS technology. Connect the antenna or RF cable directly to the back of the modem.

Connect the modem via serial cable to the computer or other device.

For More Information

Refer to the Cingular EDGE/GPRS Raven User Guide for additional information not covered in

this Quick Start Guide on how the modem works, additional configuration options, and other modem

tools and utilities to enhance your modem’s productivity.

You can find the User Guide on the AirLink Communications, Inc., website (http://

www.airlink.com) as well as the Setup Wizard, Quick Start Guide, and modem utilities.

For support assistance please email [email protected] or call 510-781-9760 Monday

through Friday 6 AM to 5 PM Pacific Standard Time.

Andere Handbücher für Raven

Inhaltsverzeichnis

Andere AirLink Communications Modem Handbücher

AirLink Communications

AirLink Communications Raven II Bedienungsanleitung

AirLink Communications

AirLink Communications Raven GPRS Bedienungsanleitung

AirLink Communications

AirLink Communications Raven C3210 Bedienungsanleitung

AirLink Communications

AirLink Communications Raven Bedienungsanleitung

AirLink Communications

AirLink Communications Version 2.40 Bedienungsanleitung

AirLink Communications

AirLink Communications 5200 Montage- und Bedienungsanleitung

AirLink Communications

AirLink Communications Redwing GPRS Bedienungsanleitung

AirLink Communications

AirLink Communications RAVEN-E EV-DO Kurzanleitung

AirLink Communications

AirLink Communications RAVEN X EV-DO X EV-DO Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung