AirLink Communications Version 2.40 Bedienungsanleitung
Copyright © 1993-2006 AirLink Communications, Inc. All rights reserved.
Raven-E iDEN
Quick Start
Version 2.40 - September 2006
September 2006 1
Raven-E iDEN for TELUS - Quick Start,
version 2.40
The SIM (Subscriber Identity Module) card in the Raven-E is a smartcard securely storing the key
identifying a mobile subscriber. Generally, you will only need to install the SIM once in the life of
the modem and it may be pre-installed by AirLink.
Installing the SIM
To install the SIM, you will only need a small phillips head screw driver.
a. Unplug the Raven-E’s power and all cables.
b. Using a small phillips head screw driver, remove the screws on the back of the Raven-E.
c. Slide the casing off of the Raven-E and set it aside.
For additional modem configuration options, please refer to the Raven-E iDEN
Users Guide for TELUS.
Note: If the SIM card was pre-installed by AirLink, there is nothing more you
need to do. Skip to the Hardware section and/or to the DUN instructions, if you
need Dial-Up Networking.
1. Opening the Case
FIGURE 1. Raven-E back
2. Ejecting the SIM tray
September 2006 2
Raven-E iDEN for TELUS - Quick Start, version 2.40
b. Slide the tray out of the slot.
FIGURE 3. Empty SIM Tray
a. Place the SIM into the tray and gently press to click it into place.
FIGURE 4. SIM Tray with a SIM
b. Slide the tray back into the modem and gently press to click it into place.
a. Using the tip of a PDA stylus, an unbent paperclip, or other slim blunt item press the yellow
button of the SIM tray. On the Raven-E, the button is between two boards.
FIGURE 2. Tray button: Raven-E
3. Inserting the SIM
The SIM may be a different color than this
example.
FIGURE 5. Inserting the SIM: Raven-E
September 2006 3
Raven-E iDEN for TELUS - Quick Start, version 2.40
a. Slide the Raven-E back into the case.
b. Secure the back of the Raven-E with the screws.
Your AirLink Raven-E should be mounted in a position that allows easy access for the cables so
they are not bent or constricted. The LEDs on the front panel should be visible for ease of opera-
4. Finishing the SIM installation
Modem Master Reset
The final step is issuing a master reset for the Raven-E. You will need to connect to theRaven-E
using a terminal application such as HyperTerminal and connect directly to theRaven-E from your
computer.
1. Connect your modem to your computer using an Ethernet cable.
2. Connect theRaven-E to power.
3. Using a terminal application, connect to the Raven-E.
FIGURE 6. Terminal connection
Enter the Master Reset Command
1. Type AT*PROVISION=000000, 0123456789
2. The Raven-E should respond with: "Master Reset Succeeded". With any other response, con-
tact TELUS to check the account status.
3. Press the reset button on the Raven-E.
FIGURE 7. Reset button
TheRaven-E should now register on the network.
Hardware Installation
September 2006 4
Raven-E iDEN for TELUS - Quick Start, version 2.40
tional verification. You should ensure that there is adequate airflow around the modem but that it is
kept free from direct exposure to the elements (sun, rain, etc.)
Your Raven-E can be used with either DC (available in most automobiles) or 110 AC (standard US
wall power) with the appropriate power adapter (available from AirLink).
The power cable positive lead should be connected to the battery or power source positive termi-
nal. The power cable negative lead should be connected to the battery or power source negative ter-
minal. The Raven-E has an internal polysilicon circuit breaker that opens at 0.5 to 1.0 amps of
current.
An optional accessory for your modem is a mounting kit. The bracket is designed to snugly cra-
dle the modem and hold it in place where you need it.
Connecting the Antenna
Antennas selected should not exceed a maximum gain of 5 dBi under standard installation config-
uration. In more complex installations (such as those requiring long lengths of cable and/or multi-
ple connections), it’s imperative that the installer follow maximum dBi gain guidelines in
accordance with Industry Canada’s regulations.
Please refer to the following guidelines:
•RSS-102 (...Health Canada’s Safety Code 6 for Exposure of Humans to RF Fields)
•RSS-129 (800 MHz Dual-Mode CDMA Cellular Telephones) (Analogue & CDMA)
•RSS-133 r1 (2 GHz Personal Communications)
For more information visit http://www.industrycanada.ca.
Your AirLink Raven-E will work with most Dual-Band PCS cellular antennas with a TNC con-
nector that works in the high and low frequencies of iDEN . Connect the antenna or RF cable
directly to the connector on the back of the Raven-E.
Connecting power
Note: When using a DC power source (such as a car battery or solar cell), AirLink
recommends placing a fuse on the line close to the power source to protect your
power source from possible surges due to shorts or other line issues.
Connecting the Raven-E to a computer or other device
September 2006 5
Raven-E iDEN for TELUS - Quick Start, version 2.40
When your Raven-E is connected to power and an antenna, there is a specific pattern to the lights
to indicate its operation mode. Refer to the User Guide for more information on light patterns.
If you encounter problems with operation of your Raven-E, AirLink’s support staff can help.
AirLink Support Web Site
The AirLink web site is updated frequently with Setup Wizards, Utilities, How-To Guides, and
other documentation: http://www.airlink.com/support.
AirLink Documentation and Guides
•Modem User Guides - These guides are specific to your modem type, cellular provider, and
cellular technology and contain comprehensive information about the operation of the modem
and its features.
•Modem Quick Start guides - These guides are also specific to the modem type, cellular pro-
vider, and cellular technology and are a step by step guide to activating the modem using the
Setup Wizard or other steps as applicable.
Your Raven-E’s Ethernet port can be connected directly to a computer or other Ethernet device
using a cross-over cable. Most newer computers have an auto-sensing Ethernet port allowing you
to use a straight through cable. If you are connecting the modem to a hub or switch you should use
a straight through cable or use the uplink port on the hub or switch with a cross-over cable.
Your Raven-E can also be connected to a USB to Ethernet device connected to a computer or
other device which does not have an available Ethernet port but does have USB.
Raven-E Indicator Lights
Tx (transmit) and Rx (receive) -Lights will flash as data is transferred to and from the Raven-E
on the remote network.
RSSI(signal level) -Light shows the strength of the signal and may be nearly solid (strong signal)
or flashing (weaker signal). A slow flash indicates a very weak signal.
Reg (registation) - Indicates the Raven-E has acquired an IP from TELUS.
Chan (channel) - Indicates the modem has acquired a network channel.
Link - Indicates a successful connection to the cellular network.
Pwr (power) -Indicates the power adapter is connected and there is power getting to the modem.
The Reset button performs the same function as unplugging power from the modem and plugging
it back in. Reset will not alter any saved configuration settings.
AirLink Technical Support
Refer to the User Guide for your modem or the AirLink website for AirLink prod-
uct warranties.
September 2006 6
Raven-E iDEN for TELUS - Quick Start, version 2.40
•Utility Guides - These guides focus on the features of one of the AirLink modem utilities:
Wireless Ace, AceView, AceNet, Modem Doctor, etc.
•Application Notes and How-To Guides - These guides detail configuring the modem to work
with a specific feature set or how the modem can be set up to work with a specific 3rd party
(non-AirLink) device.
•Data Sheets and White Papers - These are technology based information documents.
Contacting Technical Support
Friday 5 AM to 5 PM Pacific Time (8 AM to 8 PM Eastern Time). Support is not available week-
ends or holidays.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere AirLink Communications Modem Handbücher
AirLink Communications
AirLink Communications Redwing GPRS Bedienungsanleitung
AirLink Communications
AirLink Communications Raven Bedienungsanleitung
AirLink Communications
AirLink Communications RAVEN-E EV-DO Kurzanleitung
AirLink Communications
AirLink Communications Raven II Bedienungsanleitung
AirLink Communications
AirLink Communications Raven GPRS Bedienungsanleitung
AirLink Communications
AirLink Communications RAVEN X EV-DO X EV-DO Bedienungsanleitung
AirLink Communications
AirLink Communications Raven C3210 Bedienungsanleitung
AirLink Communications
AirLink Communications 5200 Montage- und Bedienungsanleitung
AirLink Communications
AirLink Communications Raven Bedienungsanleitung
Beliebte Modem Handbücher anderer Marken
Davicom
Davicom DM562AP Bedienungsanleitung
EpiValley
EpiValley TATA indicom SXC-1080 Bedienungsanleitung
Zte
Zte WiMAX Bedienungsanleitung
Intelimax
Intelimax MA-2060 Bedienungsanleitung
SMC Networks
SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch
Telstra
Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung
US Robotics
US Robotics 3453C Bedienungsanleitung
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung
Zte
Zte MF823 Bedienungsanleitung
Four-Faith
Four-Faith F1403 Bedienungsanleitung
Sierra Wireless
Sierra Wireless AIRLINK MP595W Bedienungsanleitung
Gemtek
Gemtek WiMAX WIXFBR-103 Bedienungsanleitung