Airlinkplus RT211W Bedienungsanleitung

Ver. 5A

This Quick Installation Guide only provides you with some basic instructions. For more

detailed information, please refer to the User Manual on the supplied CD.

Quick Installation Guide

Package Content:

•802.11g access point

•Power Adapter

•Category 5 UTP cable

•Utility CD

•Quick Installation Guide

1Connecting the Access Poing (AP)

Prior to connecting the hardware, make sure to power off

your Ethernet device, Cable/ADSL modem and AP. Then

follow the steps below to connect the related devices.

Step 1 Connecting the power adapter.

Connect the single DC output connector of the power adapter

to the power jack on the back of the AP. Then connect the

supplied power cord to the power adapter and the other end to

an AC outlet.

Step 2 Connecting to Ethernet network.

Attach one end of the Ethernet cable with RJ-45 connectors to

your hub, switch or a PCs Ethernet port, and the other end to

the LAN port of your AP.

Setting Up Ethernet/WLAN Client

You can choose to access the APs Web interface via Ethernet or

wireless network. Whatever your choice, you must properly

configure the network settings of your PC to be in the same

subnet with the AP. As the AP is shipped with these defaults:

Step 1

Click the Start button. Select Settings and/or click the Control

Panel icon.

For Windows 98 and ME, double-click the Network icon.

For Windows 2000, double-click the Network and Dial-up Con-

nections icon. Double-click the Local Area Connection x.

For Windows XP, click the Network and Internet Connections

icon. Click the Network Connections. Double click the Local

Area Connection x under LAN or High-Speed Internet.

Model # RT211W

•IP address: 192.168.1.1

•Subnet mask: 255.255.255.0

•DHCP server: Disabled

Therefore, you should configure your PC’s TCP/IP settings to use

a static IP as below:

•IP address: 192.168.1.x (x is between 2 and 254)

•Subnet mask: 255.255.255.0

•Gateway: 192.168.1.1

Note: Before you change the TCP/IP configuration, you should write

down your original configuration setting in case you need to restore it

later.

Note: snap shots are for Windows 2000 and XP

Step 2

For Windows 98 and ME,

Select “TCP/IP -> Your

Ethernet Adapter”, Click the

Properties button. Go to step

For Windows 2000 and XP,

click the Properties button in

the Local Area Connection

Status window.

Step 3 For Windows 2000 and XP

only, Make sure the Internet

Protocol (TCP/IP) is checked and

highlighted in the Local Area

Connection Properties window.

Click the Properties button.

Step 4

For Windows 98 and ME, select

Specify an IP adress and fill the

fields below with the values

mentioned above in theTCP/IP

properties window.

For Window 2000 and XP, select

Use the following IP address and

fill the fields below with the values

mentioned above in theInternet

protocol (TCP/IP) properties

window.

Step 5 Click the OK button and restart the computer. Continue on back...

If you choose to manage the AP via a wireless client, please also check

the following:

1. Make sure your PC is equipped with 802.11g or 802.11b wireless

adapter and has appropriate WLAN card driver / utility and TCP/IP

installed.

2. Set the wireless adapter to use appropriate TCP/IP settings as

described in previous section

3. Launch the wireless adapter’s provided utility and verify that your

wireless client is configured with these settings:

•Operation Mode: Infrastructure

•SSID: 11g AP

•Authentication: Open

•WEP Mode: Disabled

Checking the Connection to the AP

After configuring the TCP/IP protocol, you can use the ping command

to verify if your LAN/Wireless computer has successfully connected to

the AP.

To execute ping command, open the DOS window by clicking on

Start -> Run. In the Run window, type Command. At the DOS prompt,

type the following command:

ping 192.168.1.1

If the Command window returns something similar to the following:

Reply from 192.168.1.1 bytes=32 time=100ms TTL=253

Then the connection between the AP and your computer has been

successfully established. If the computer fails to connect to the AP, the

Command window will return the following:

Request time out

Veryfy your computer's network settings are correct and check the cable

connection between the AP and the computer.

Accessing the Web-Based Configuration Utility

Step 1 Start your Web browser and type http://192.168.1.1 in the URL

field. This is your AP's default private IP address.

Step 2 After connecting to the

device, you will be prompted to

enter the username and password.

Leave the username empty and

enter the default password as

admin.

Step 3 The Web-Based utility will appear with the System Overview

table selected.

5LAN Configuration

Click the LAN page link to configure the LAN interface.

Manually Specifying an IP address

If you want to reconfigure the IP information of the AP to match your

existed LAN, just pick one available IP address and the same Subnet

Mask and Default Gateway for your LAN. Enable the Manual Config

option and enter your new settings in the provided fields.

Enabling DHCP Server

The AP implements a built-in DHCP server which can be used to

dynamically assign IP addresses to the DHCP clients on the LAN/WLAN.

To use DHCP server function, make sure you have properly set the AP’s

IP address, enable the DHCP service, then enter the DHCP Lease Time

and IP Pool Range fields.

Setting the AP to be DHCP Client

If your network has already deployed a DHCP server, you should set

the AP to be a DHCP client. The AP will request an IP Address from

the DHCP server when rebooted or powered up.

After you enable the DHCP client option and apply the change, your

PC will lose the communication to the AP. Since the IP address

assigned to the AP could come from a large DHCP address pool, you

will need a third-party tool to identify the APs IP address.

Note: Changing the LAN settings may cause the PC from which you

configure the AP to lose the communication to the AP. To reconnect, you

will need to reconfigure your PC to use an IP address compatible with

the new IP address.

Click Wireless LAN(2.4G) to configure the wireless settings of the AP.

6Wireless LAN (2.4G) Configuration

7Technical Support

Email: [email protected]

Website: www.airlinkplus.com

Congratulations! You’ve successfully configured your AP.

You should customize the SSID and Channel settings as needed. For added

security, you should enable WEP encryption and firewall following instructions

from the manual included in the CD.

The following describes the basic wireless configurations:

Access Point Name: The name used for identifying the Access Point.

SSID: Service Set ID. It uniquely identifies a logical network domain

name of your WLAN.

Network Type: An “Open” AP will periodically broadcast its SSID to

allow the wireless clients to recognize their presence. However, this

creates a security hole since any wireless station with SSID set to “any”

or got the broadcast may associate to your AP. It is recommended to

set this option to Closed to have your AP only accept stations whose

SSID are the same as this AP.

Country: Select the country where you use this AP. When the country

setting is changed, the AP scans only the legal frequency channels

allowed in that regulatory domain.

Channel ID: The radio frequency used for communication. Available

channels vary according to the regulations in the country you specified

in the Country drop-down list. Select a channel out of the available

cannels or use the default channel.

Andere Handbücher für RT211W

Inhaltsverzeichnis

Andere Airlinkplus Drahtloser Zugangspunkt Handbücher

Airlinkplus

Airlinkplus RT211W Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung