Akuvox E12 Bedienungsanleitung
Wall-mounting
bracket x 1
E12 x 1 M3x4 crosshead screw x 4Plastic wall anchor x 4
6-PIN cable x 1ST4x20 crosshead screw x 4
Camera
RF Card Reader（Except E12N）
Call Button
E12
Mic
Wiring cover x 1
7-PIN cable x 1
Before you being using the device, please check the version you obtained and ensure that the following
items are included in the shipped box:
M3x6 Torx head screw x 2 Wall-mounting template x 1 Diode x 1
Torx wrench x 1
E12
Photosensitive Sensor
Unpacking
Product Overview
Universal Accessories :
White Light LED
2
E12
Insert four plastic wall anchors into the
holes.
Fix the wall-mounting bracket on the
wall by tightening four ST4x20
crosshead screws to the plastic wall
anchors.
Backlight Direct sun
through window
Close to lightDirect sunlight Indirect sunlight
through window
Please do not place device under direct sunlight, it will bring bad effect or be broken with high temperature.
If installing the device indoors, please keep device at least 2 meters away from light, and at least 3 meters away from
window and door.
Installation Environment
Installation
According to the position of the
reserved wires on the wall, stick the
wall-mounting template vertically to
ensure that the wires can come out of
the shadow position of template. Drill
(6 mm drill bit required) four screw
holes with a depth of 25mm in the
screw holes of the template.
3
SIP Video Phone
LAN
PoE
E12S/W
PoE
PC (third party)
PoE
Hang the device on to the two square
hangers on the wall-mounting bracket,
then use the Torx wrench attached to
tighten the bottom of the device with
two M3x6 Torx head screws.
E12
The installation is completed.
Indoor Monitor
PON
E12N
Application Network Topology
Connect the wires to the interface of
the device as needed (for details,
refer to “Device Wiring”). After
arranging the wires, tighten the
wiring cover using four M3x4
crosshead screws to the device.
4
E12
When you connect a device containing a
coil, such as a relay or an electromagnetic
lock, it is necessary to protect the
intercom against voltage peak while
switching off the induction load. For this
way of protection we recommend a diode
1 A / 200 V (included in the accessories)
connected antiparallet to the device.
Warning
Device Wiring
Wire Length & AWG Table
Please follow the properly measured wire gauge/length to install device:
20 AWG 22 AWG 24 AWG 26 AWG
12V 1A Adapter ≤50m ≤40m /
≤20m
5
Make a call:
Receive a call:
E12
IP Announcement
Operation
Configuration
1. Access the Web UI: Input the IP address into browser to configure the phone.
2. Account Registration: On web UI, go to the path: Account > Basic page Register Account and fill in the account
information. ( Please refer to user manual for more information)
3. Configure the Push Button: On web UI, go to the path: Intercom > Basic > Push Button to configure the call
number.
4. Configure the code to open the relay: On web UI, go to the path: Intercom > Relay&Input > Relay ID/DTMF and
choose the DTMF code number in corresponding area.
E12 supports Auto Answer by default. Incoming call from indoor device will be answered automatically.
1. Press the Call Button to call indoor SIP Phone.
2. During the talk, called party can press pre-configured code number to unlock the door.
1. While E12 starts up normally, hold the Call Button for several seconds after the LED light turns blue, voice system
will enter IP announcement mode.
2. In announcement mode, the IP address will be announced periodically.
3. Press Call Button again to the announcement mode.
4. In announcement mode, phone announces "IP 0.0.0.0" if no IP address is gained.
6
E12
Notice Information
Note: For more LED settings, please refer to E12 web UI: Intercom > LED Setting.
Blue Light Always On
Blue Breathing Light
Blue Light Always On > Red Light Always
On > Purple Light Always On
Red Breathing Light
Red/Purple Light Flashing
Purple Light Always On
Receiving a call
Network is unavailable / Obtaining network
Talking
Restarting
Calling
Normal status
Firmware upgrading
Status
Indicator
Name Status Description
Indicators
Information contained in this document is believed to be accurate and reliable at the time of printing. This
document is subject to change without notice, any update to this document can be viewed on Akuvox’ s website:
http://www.akuvox.com © Copyright 2022 Akuvox Ltd. All rights reserved.
AKUVOX (XIAMEN) NETWORKS CO., LTD.
Add.: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA
www.akuvox.com
Andere Handbücher für E12
2
Inhaltsverzeichnis
Andere Akuvox Gegensprechanlage Handbücher
Akuvox
Akuvox IT82 Series Bedienungsanleitung
Akuvox
Akuvox A01X Bedienungsanleitung
Akuvox
Akuvox A05 Series Service-Handbuch
Akuvox
Akuvox R20A Handbuch
Akuvox
Akuvox E12 Bedienungsanleitung
Akuvox
Akuvox C313 Series Bedienungsanleitung
Akuvox
Akuvox E16 Series Bedienungsanleitung
Akuvox
Akuvox R26X Bedienungsanleitung
Akuvox
Akuvox IT82 Series Bedienungsanleitung
Akuvox
Akuvox R29C Montageanleitung
Akuvox
Akuvox R20A Handbuch
Akuvox
Akuvox E16 Series Service-Handbuch
Akuvox
Akuvox R29 Series Handbuch
Akuvox
Akuvox R20A Bedienungsanleitung
Akuvox
Akuvox R27V Handbuch
Akuvox
Akuvox E16 Series Service-Handbuch
Akuvox
Akuvox E16 Series Service-Handbuch
Akuvox
Akuvox X915 Series Bedienungsanleitung
Akuvox
Akuvox X916 series Bedienungsanleitung
Akuvox
Akuvox E18 Bedienungsanleitung
