Albatron PXP43 Bedienungsanleitung

Preface

PXP43 Motherboard User’s Guide

Preface

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

FederalCommunicationsCommission(FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system’s manu-

facturer could void the user’s authority to operate the equipment.

TrademarkRecognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Preface

PXP43 Motherboard User’s Guide

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interfer-

ence that may cause undesired operation

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur

le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Software Setup

Describes features of the

motherboard.

Go to page 1

Describes installation of

motherboard components.

Go to page 6

Provides information on us-

ing the BIOS Setup Utility.

Go to page 23

Describes the motherboard

software

Go to page 39

iii

PXP43 Motherboard User’s Guide

TABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

Preface i

Chapter 1 1

IntroducingtheMotherboard 1

Introduction......................................................................................1

Feature..............................................................................................2

MotherboardComponents.............................................................4

Chapter 3 23

UsingBIOS 23

Aboutthe SetupUtility................................................................23

The Standard Configuration..............................................23

Entering the Setup Utility...................................................23

Updating the BIOS............................................................25

UsingBIOS......................................................................................25

Standard CMOS Setup......................................................26

Advanced Setup.................................................................28

Advanced Chipset Setup....................................................30

Chapter 2 66

Installing the Motherboard 6

SafetyPrecautions.............................................................................6

Choosinga ComputerCase..............................................................6

Installingthe Motherboard in a Case.............................................6

CheckingJumper Settings................................................................7

Setting Jumpers.........................................................................7

Checking Jumper Settings.........................................................8

Jumper Settings.........................................................................8

InstallingHardware..........................................................................9

Installing the Processor...........................................................9

Installing Memory Modules.....................................................11

Expansion Slots.......................................................................13

Connecting Optional Devices..................................................15

Installing a Hard Disk Drive/CD-ROM/SATAHard Drive......17

ConnectingI/O Devices..................................................................19

ConnectingCase Components......................................................20

Front Panel Header..................................................................22

PXP43 Motherboard User’s Guide

Integrated Peripherals.......................................................31

Power Management Setup.................................................32

PCI/PnP Setup...................................................................33

PC Health Status................................................................34

Frequency/Voltage Control................................................35

Load Default Settings.......................................................37

Supervisor Password........................................................37

User Password..................................................................38

Save & Exit Setup..............................................................38

Exit Without Saving............................................................38

4retpahC 3939

3939

93erawtfoS Setup

Software List..........................................................................................39

Software Installation.............................................................................39

IntroducingtheMotherboard

Chapter 1: Introducing the Motherboard

Chapter1

IntroducingtheMotherboard

Introduction

Thank you for choosing the PXP43 motherboard. This motherboard is a high per-

formance, enhanced function motherboard designed to support the LGA775 socket

Intel®Yorkfield/Wolfdale processors for high-end business or personal desktop mar-

kets.

There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and

keyboard connectors, COM, four USB ports, one LAN port and audio jacks for

microphone, line-in and 6-ch line-out.

The ICH10 Southbridge supports two PCI slots which are PCI v2.3 compliant. In

addition, three PCI Express x1 slots are supported, fully compliant to the PCI

Express Base Specification, Revision 1.1. It implements an EHCI compliant inter-

face that provides 480 Mb/s bandwidth for twelve USB 2.0 ports (four USB ports and

four USB 2.0 headers support additional eight USB ports). One onboard IDE connec-

tor supports two IDE devices in Ultra ATA 133/100/66/33 mode. The Southbridge

supports six SATA ports with maximum transfer rate up to 3.0 Gb/s each.

The motherboard incorporates the Intel Eaglelake P43 Northbridge (NB) and Intel

ICH10 Southbridge (SB) chipsets. The Northbridge supports a Front Side Bus (FSB)

frequency of 1333/1066/800 MHz using a scalable FSB Vcc_CPU. The memory

controller supports DDR2 memory DIMM frequencies of 800/667. It supports four

DDR2 sockets with maximum memory size of 16 GB. DDR2 memory bandwidth of

12.8 GB/s in dual-channel symmetric mode assuming DDR2 800 MHz. High resolu-

tion graphics via one PCI Express x16 slot, intended for Graphics Interface, is fully

compliant to the PCI Express Base Specification Revision 2.0.

IntroducingtheMotherboard

PXP43 Motherboard User’s Guide

Feature

Processor

Chipset

• Supports DDR2 800/667 DDR2 SDRAM with Dual-channel architecture

• Accommodates four unbuffered DIMMs

• Up to 4 GB per DIMM with maximum memory size up to 16 GB

Memory

Audio

• 5.1 Channel High DefinitionAudio Codec

• ADCs supports 44.1k/48k/96kHz sample rate

• Meets Microsoft WLP 3.08 Vista premium and mobile PCs audio

requirements

• Direct Sound 3DTM compatible

This motherboard uses an LGA775 type of Intel®Yorkfield/Wolfdale that carries

the following features:

• Accommodates Intel®Yorkfield/Wolfdale processors

• Supports a system bus (FSB) of 1333/1066/800 MHz

The P43 Northbridge (NB) and ICH10 Southbridge (SB) chipsets are based on an

innovative and scalable architecture with proven reliability and performance.

P43 (NB) • Supports 36-bit host bus addressing, allowing the

CPU to access the entire 64 GB of the memory ad-

dress space.

• 2 GB/s point-to-point Direct Media Interface (DMI) to

ICH10 (1 GB/s each direction)

• One, 16-lane PCI Express x16 port for Graphics At-

tach, compliant to the PCI Express Base Specification

revision 2.0

• Supports 512-Mb and 1-Gb DDR2 and 512-Mb, 1-

Gb,and 2-Gb DDR3 DRAM technologies for x8 and

x16 devices

ICH10 (SB) • EnhancedDMAController,interruptcontroller,andtimer

functions

• Compliant with PCI Express Base Specification, revi-

sion 1.1

• Compliant with PCI v2.3 specificaiton

• Compliant with SATA 3.0 Gb/s Host Controller

• Integrated USB 2.0 Host Controller supporting up to

twelve USB 2.0 ports

(Realtek 6CH Audio ALC662 Codec)

IntroducingtheMotherboard

Chapter 1: Introducing the Motherboard

This motherboard supports Ultra DMA bus mastering with transfer rates of 133/

100/66/33 Mb/s.

• One PCI Express x16 slot for Graphics Interface

• Three PCI Express x1 slots

• Two 32-bit PCI v2.3 compliant slots

• One IDE connector supporting up to two IDE devices

• Six 7-pin SATA connectors

Expansion Options

Integrated I/O

The motherboard comes with the following expansion options:

• Two PS/2 ports for mouse and keyboard

• One Serial port

• Four USB ports

• One LAN port

• Audio jacks for microphone, line-in and 6-ch line-out

BIOS Firmware

• Power management

• Wake-up alarms

• CPUparameters

• CPUandmemorytiming

1. Some hardware specifications and software items are subject to change

without prior notice.

The motherboard has a full set of I/O ports and connectors:

The motherboard uses AMI BIOS that enables users to configure many system

features including the following:

The firmware can also be used to set parameters for different processor clock

speeds.

2. Due to chipset limitation, we recommend that motherboard be oper-

ated in the ambiance between 0 and 50 °C.

Onboard LAN (

• Integrated PHY for 10/100/1000 Mbps

• IEEE 802.3x compliant flow control support

• Three power supplies: 2.5V, 1.8V and 1.2V

• PCI Express base 1.1 compliant

Atheros AR8121 PCI-E Gbit LAN)

IntroducingtheMotherboard

PXP43 Motherboard User’s Guide

MotherboardComponents

IntroducingtheMotherboard

Chapter 1: Introducing the Motherboard

Table of Motherboard Components

This concludes Chapter 1. The next chapter explains how to install the motherboard.

LABEL COMPONENTS

1. CPU Socket LGA775 socket Intel®Yorkfield/Wolfdale

Family processors

2. CPU_FAN1 CPU coolingfan connector

3. DDR2_DIMM1~4 240-pin DDR2 SDRAM slots

4. ATX_POWER Standard24-Pin ATX Power connector

5. SATA1~6 Serial ATA connectors

6. CASE_FAN Case coolingfan connector

7. F_PANEL Front Panel Switch/LED header

8. USBPWR_F1~2 Front Panel USB Power Select jumpers

9. F_USB1~4 Front Panel USB headers

10. SPK Speaker header

11. CLR_CMOS Clear CMOS jumper

12. IDE Primary IDE connector

13. SPDIFO SPDIF out header

14. F_AUDIO Front Panel Audio header

15. CD_IN Analog Audio Input connector

16. PCI2~3 32-bit add-on card slots

17. PCIE1~3 PCI Express x1 slots

18. PCIE16X_1 PCI Express x16 graphics cardslot

19. USBPWR_R1 Rear Panel USB/PS2 Power Select jumper

20. ATX12V 4-pin +12Vpower connector

21. SYS_FAN1 System coolingfan connector

InstallingtheMotherboard

PXP43 Motherboard User’s Guide

Chapter2

InstallingtheMotherboard

SafetyPrecautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid dam-

age from static electricity

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

ChoosingaComputer Case

There are many types of computer cases on the market. The motherboard complies

with the specifications for the FULL ATX system case. Firstly, some features on the

motherboard are implemented by cabling connectors on the motherboard to indica-

tors and switches on the system case. Make sure that your case supports all the

features required. Secondly, this motherboard supports two enhanced IDE drives.

Make sure that your case has sufficient power and space for all drives that you intend

to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O

template in the case matches the I/O ports installed on the rear edge of the

motherboard.

This motherboard carries a FULL ATX form factor of 305 x 244 mm. Choose a case

that accommodates this form factor.

Installingthe Motherboard ina Case

Refer to the following illustration and instructions for installing the motherboard in

a case.

Most system cases have mounting brackets installed in the case, which correspond

the holes in the motherboard. Place the motherboard over the mounting brackets

and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion

slots on your motherboard.

Andere Handbücher für PXP43

Inhaltsverzeichnis

Andere Albatron Hauptplatine Handbücher

Albatron

Albatron P4M800-775 Bedienungsanleitung

Albatron

Albatron PM915-478 Bedienungsanleitung

Albatron

Albatron PXP35 Bedienungsanleitung

Albatron

Albatron PMH55 Bedienungsanleitung

Albatron

Albatron PX915P-2V Bedienungsanleitung

Albatron

Albatron K8Ultra-U Series Bedienungsanleitung

Albatron

Albatron PM73V Bedienungsanleitung

Albatron

Albatron KM266 Series Bedienungsanleitung

Albatron

Albatron PM 845G Series Bedienungsanleitung

Albatron

Albatron KI690-AM2 Bedienungsanleitung

Albatron

Albatron KX550 Bedienungsanleitung

Albatron

Albatron KX600A Series Bedienungsanleitung

Albatron

Albatron K8X250 Bedienungsanleitung

Albatron

Albatron PX845PE Series Bedienungsanleitung

Albatron

Albatron KM400T-8X Series Bedienungsanleitung

Albatron

Albatron ABOX 865G SERIES Bedienungsanleitung

Albatron

Albatron K8X890 Series Bedienungsanleitung

Albatron

Albatron PXP45 Bedienungsanleitung

Albatron

Albatron PM945GC Bedienungsanleitung

Albatron

Albatron K8X890 Series Bedienungsanleitung

Albatron

Albatron PX845GEV Series Bedienungsanleitung

Albatron

Albatron PM800 Series Bedienungsanleitung

Albatron

Albatron K8NF4X-754 Bedienungsanleitung

Albatron

Albatron KM61S-AM2 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung