Alcatel OmniAccess AP60 Installationsanleitung

The AP60/61 Mounting Kit Installation Notes 1

The AP60/61

Mounting Kit Installation Notes

The AP60-MNT can be used to attach an AP60 or AP61 Access

Point (AP) to a shelf, wall, post, ceiling, or partition hanger. The

included mounting cradle holds the AP firmly in place when

installed, and also allows for quick release when maintenance is

required.

These Installation Notes provide instructions for using the

mounting kit and modify information found in the AP60/61

Wireless Access Point Installation Guide. Please keep this

information with your Wireless Networks documentation.

Kit Components

The following items are included in the AP60-MNT:

FIGURE 1 AP60/61 Mounting Kit Packing List

15/16"

T-Rail Clip

9/16"

T-Rail Clip

Nut

Label

Cover

Cross-head

Screw

AP60-MNT: Installation Notes

2Part 0500037-03 May 2005

Inform your supplier if there are any incorrect, missing or damaged parts. If

possible, retain the original packing materials. Use them to repack the product

in case there is a need to return it.

Prerequisites

Before using the mounting kit, you must first perform the initial AP

provisioning as described in the AP60/61 Wireless Access Point Installation

Guide. When handling the AP, be sure to follow the requirements and safety

precautions outlined in that manual.

Mounting the AP Cradle

The mounting kit can be used to install the AP60/61 in a variety of ways, each

of which is detailed in the following sections:

zOn a solid wall, shelf, or ceiling surface (see page 3)

zSuspended from a tile ceiling (see page 4)

zOn a vertical post (see page 6)

zFrom an office partition hanger (see page 6)

The following procedures describe mounting the AP cradle. The AP is then

inserted into the cradle as shown on page 7.

The AP60/61 Mounting Kit Installation Notes 3

Solid Surface Mount

The mounting kit can be used to attach the AP to a solid, flat, indoor surface

such as a wall, shelf, and ceilings.

FIGURE 2 Attaching the Cradle to a Solid Surface

Orient the cradle with its flat side against the mounting surface. If attaching

the cradle to a wall, orient it so that the notched end is positioned at the top.

Secure the cradle to the solid surface using four #6 screws (not included) or

equivalent. Use the round cradle holes (A) for solid surfaces. If attaching the

cradle to drywall, use the wide cradle holes (B) and the appropriate wall

anchors (not included) as shown above.

CAUTION—Do not use screws to attach the mounting cradle to a

suspended ceiling or other structurally weak surface. For suspended

ceilings, use the T-rail clips as described on page 4.

AP60-MNT: Installation Notes

4Part 0500037-03 May 2005

Suspended Ceiling Mount

The mounting kit can be used to hang the AP from an indoor suspended

ceiling.

1. Attach the T-rail clips to the ceiling rail.

FIGURE 3 Attaching the T-Rail Clips

The T-rail clip twists onto the ceiling rails used with standard suspended-ceiling

systems. Use either the 15/16-inch or 9/16-inch clip, as appropriate for your

ceiling. Use the mounting cradle to gauge the appropriate separation.

The AP60/61 Mounting Kit Installation Notes 5

2. Attach the cradle to the T-rail clip.

FIGURE 4 Mounting the Cradle to a Suspended Ceiling

3. Place the nut on the T-rail clip bolt to secure the cradle.

Cradle

T-Rail

Clip

Nut

Side View

Bolt

Hole

AP60-MNT: Installation Notes

6Part 0500037-03 May 2005

Vertical Post Mount

FIGURE 5 Mounting the Cradle to a Vertical Post

To mount the AP to a vertical post, thread two metal or plastic mounting straps

(not included) around the post and through the large slots on the cradle. The

straps should be flat and no wider than 1.5 cm (5/8 inches).

Office Partition Mount

FIGURE 6 Mounting the Cradle to a Partition Hanger

Strap

Slots

Hook/Bolt

Holes

The AP60/61 Mounting Kit Installation Notes 7

The cradle includes mounting holes for a variety of different office partition

hangers (not included). Use the hole most suited for your particular hanger

system’s hook or bolt.

Placing the AP into the Cradle

1. Remove the oval LED label from the front of the AP chassis.

FIGURE 7 Removing the LED label

The label conceals a mounting hole required in a later step. (You will remove

and discard this label and replace it with the extra label shipped with this kit.)

AP60-MNT: Installation Notes

8Part 0500037-03 May 2005

2. Place the AP into the mounting cradle.

FIGURE 8 Placing the AP60/61 into the Cradle

Fit the keyhole-shaped slots on the rear of the AP chassis over the cradle

mounting pin and tab. Slide the AP chassis downward so that the AP slot

captures the tab.

The AP60/61 Mounting Kit Installation Notes 9

3. Secure the AP with one of the included screws.

FIGURE 9 Installing the Cradle Screw

Use either the cross-head or hex-head screw. The hex-head screw requires a

less commonly available tool and may increase casual security. Install the

screw through the mounting hole in the front of the AP chassis (previously

covered by the LED label) and into the cradle mounting pin. Do not overtighten.

4. Apply the new LED label.

5. Secure the AP, if desired.

To prevent the unauthorized removal of the AP from its installed location, use a

Kensington MicroSaver Security Cable (not included). Wrap the security cable

around an immovable object, insert the cable’s lock into the Kensington

Security Slot on the back of the AP, and turn the key.

6. Orient the antennas.

For best performance, orient the antennas vertically.

7. Resume standard installation.

Once mounting is complete, connect the required cables and complete the

installation as described in the AP60/61 Wireless Access Point Installation

Guide.

AP60-MNT: Installation Notes

10 Part 0500037-03 May 2005

Notes

Andere Handbücher für OmniAccess AP60

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alcatel Drahtloser Zugangspunkt Handbücher

Alcatel

Alcatel OmniAccess OAW-AP70 Bedienungsanleitung

Alcatel

Alcatel OmniAccess OAW-AP65 Bedienungsanleitung

Alcatel

Alcatel OmniAccess 1200R Bedienungsanleitung

Alcatel

Alcatel OAW-AP80M Bedienungsanleitung

Alcatel

Alcatel ONETOUCH W600 Bedienungsanleitung

Alcatel

Alcatel Lucent 300 Series Bedienungsanleitung

Alcatel

Alcatel OmniAccess AP60 Bedienungsanleitung

Alcatel

Alcatel OmniAccess AP70 Bedienungsanleitung

Alcatel

Alcatel ONETOUCH Y580 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung