ALcom Clarigo C11 Handbuch
1
2
Contents
Setup Flow Chart...................................................... .... ..3
Part I. System Information
1.1 Reset to default................................................. ... ..4
1.2 Firmware version............................................... .. ..4
Part II. Interface Setting
2.1 Interface ........................................................... .....5
Part III. Keyboard Parameters
3.1 Terminal Type .................................................... ...6
3.2 Language Selection ......................................... .....7
3.3 Function Key Emulation ................................ ..... .8
3.4 Keyboard Emulation .................................... .........8
3.5 ALT Mode ..................................................... ........9
3.6 Caps Lock ..................................................... ........9
3.7 Numeric Key .................................................. .......9
3.8 Inter-Character Delay .................................... ......10
3.9 Delay After Transmit (Keyboard Wedge) ...... ......10
3.10 Keyboard Speed ........................................... ....10
3.11 Keyboard Wedge Terminator ......................... ...10
Part IV. RS-232 Protocol
4.1 Baud Rate ................................................... ...... .11
4.2 Data Bits ....................................................... ..... 11
4.3 Stop Bits ....................................................... ... .12
4.4 Parity Check .................................................. ... 12
4.5 Inter-Character Delay ...................................... . ..12
4.6 Delay After Transmit ...................................... ... . 12
4.7 Response Delay Time .................................... ... .13
4.8 Flow Control .................................................... . ..13
4.9 RS-232 Interface Terminator ......................... ... ..13
Part V. System Setting
5.1 Scan Mode .................................................... .. ...15
3
5.2 Buzzer ......................................................... ........16
5.3 String ............................................................. .....18
5.4 Barcode Inverse .......................................... ........20
Part VI. Barcode Type Setting
6.1 UPC-A ....................................................... ..........22
6.2 UPC-E ..................................................... ............24
6.3 EAN-13........................................................... .....26
6.4 EAN-8................................................... ...............28
6.5 Code 39...................................................... .........29
6.6 Codabar....................................................... ........32
6.7 Code 93......................................................... ......34
6.8 Code 128 .................................................... ........36
6.9 Interleaved 2 of 5......................................... .......38
6.10 Industrial 2 of 5.......................................... ........40
6.11 Matrix 2 of 5............................................ ...........42
6.12 China Post Code.................................... .......... .44
6.13 MSI/Plessey........................................... ......... ..45
6.14 Code 32................................................... ..........47
6.15 Code 11........................................................ .....49
6.16 RSS (Optional) ......................................... ...... . 51
6.17 Telepen ................................................. ........... 52
Appendix A.................................................... ............ . 54
Appendix B................................................... .......... . 56
4
Setup Flow Chart
◆Note:
Note:Note:
Note:
1. Scan “firmware version barcode”, the
Version No. will
be displayed on monitor.
The default settings are shown with < > and bold in the
following sections.
Scan “End” barcode
Scan the barcode you like to
change to change
Hex or ASCII Code
Reset to default
YES
NO
5
Part I
Part I Part I
Part I System
SystemSystem
System
Information
InformationInformation
Information
1.1 Reset to default
Reset to defaultReset to default
Reset to default:
::
:
Reset to factory default settings. The default s
ettings
are shown with < > and bold.
1.2 Display
Display Display
Display Firmware Version
Firmware VersionFirmware Version
Firmware Version:
::
:
Scan barcode to display firmware version.
Start Configuration
Reset to default
Firmware Version
End Configuration
6
Part II System Setting
2.1 Interface:
2.1 Interface:2.1 Interface:
2.1 Interface:
Part I System Information
7
1.3 Reset to default:
Reset to factory default settings. The default settings are
shown with < > and bold.
1.4 Display Firmware Version:
Scan barcode to display firmware version.
Start Configuration
Reset to default
Firmware Version
End Configuration
Part II System Setting
8
2.1 Interface:
Start Configuration
PS/2
Keyboard
RS-232
< USB
Keyboard >
< USB
Virtual COM >
End Configuration
Part III Keyboard wedge parameters
9
3.1 Terminal Type:
Start Configuration
< IBM AT >
Reserved
Reserved
Reserved
Reserved
Reserved
10
Reserved
Reserved
End Configuration
3.2 Language Selection:
Start Configuration
American
Italian
Spanish
Inhaltsverzeichnis
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
