Alfa Network MATRIXPRO 2 Bedienungsanleitung
1
MATRIXPRO 2
User manual
2
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
1. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
2. The antenna(s) used for this transmitter must not be co-located of operating in
conjunction with any other antenna or transmitter.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. Ln order to avoid the possibility of exceeding the Fcc
3
radio frequency exposure limits, human proximity to the antenna shall not be less
than 21cm (8inches) during normal operation.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable
to only Mobile Configurations. The antennas used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
4
CONTENTS
Product introduction
1. Product interface introduction
2. Product function brief
※AP Bridge Mode
※Client Bridge Mode
※WDS Mode
How to Apply MATRIXPRO 2
3. How to Install MATRIXPRO 2
Device
4. How to Configure MATRIXPRO 2
4-1. How to Setup your PC
4-2. MATRIXPRO 2's Function
Settings
※AP Bridge Mode Setting
※Client Bridge Mode Setting
※WDS Mode Setting
5
Product introduction
1. Product interface introduction
Dashboard: Show the current status information about the
MATRIXPRO 2.
Wizard: Configure your MATRIXPRO 2 quickly and work it.
Network: Configure Local Network IP, Subnet Mask, etc., and
enable DHCP Server.
Wireless: Setup Wireless Settings on your MATRIXPRO 2.
System: Important settings for related information with
hardware.
6
2. Product function brief
There are 3 operation Modes, AP Bridge
Mode, Client Bridge Mode, and WDS Mode
can be selected
※AP Bridge Mode: The AP Mode is the most commonly and
widely used mode of operation. Let mobile devices such as
smart phones, tablets, etc. access Internet.
※Client Bridge Mode: In Client Mode, the MATRIXPRO 2 is
receive other wireless signals; the unlimited device only be
used by connecting to the MATRIXPRO 2.
※WDS Mode: Provides service operate in one of three
modes; WDS AP Mode, WDS Client Mode, or WDS Repeater
Mode. Please refer to the detailed instructions in section 4-2.
7
1) WDS AP Mode: WDS AP Mode is an access point, but it
only work on other WDS Mode
2) WDS Client Mode: WDS Client, in which WDS APs
communicate with WDS Client to access them
3) WDS Repeater Mode: WDS repeater, in which WDS Aps
communicate with each other and with WDS Client. And
extend the original wireless signal.
8
How to Apply MATRIXPRO 2
3. How to Install MATRIXPRO 2
Device
1) Connect the PC in PoE LAN port or normal LAN port of
MATRIXPRO 2.
2) Connect the power to MATRIXPRO 2.
9
4. How to Configure MATRIXPRO 2
4-1. How to Setup your PC
Follow the steps below to configure in Windows OS.
1) Press on the Windows Key and Xon your Keyboard.
2) On the menu that appears and click Network Connections.
3) On the Network Connections screen; Right click on Local
10
Area Connection and click Properties (if your Windows OS
is Windows 10, click Change adapter settings first and
follow up the step)
4) Click Internet Protocol Version 4 (TCP/IP) then click
Properties
Inhaltsverzeichnis
Andere Alfa Network Netzwerk-Router Handbücher
Alfa Network
Alfa Network AIP-610H Bedienungsanleitung
Alfa Network
Alfa Network AP121U Bedienungsanleitung
Alfa Network
Alfa Network Data Traveller Bedienungsanleitung
Alfa Network
Alfa Network AIP-W610 Bedienungsanleitung
Alfa Network
Alfa Network ADS-R02 Bedienungsanleitung
Alfa Network
Alfa Network AHPE301 Bedienungsanleitung
Alfa Network
Alfa Network AIP-W525H V2 Bedienungsanleitung
Alfa Network
Alfa Network R36AH Bedienungsanleitung
Alfa Network
Alfa Network AHPE201 Bedienungsanleitung
Alfa Network
Alfa Network AWAP602HW Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise