Alfa Network AWAP05O Bedienungsanleitung

Dual-Band Outdoor Access Point /

Bridge

User Guide

Guide

Dual-Band Outdoor Access Point / Bridge

IEEE 802.11a/b/g Access Point / Bridge

Master unit with External Antenna Options

Slave unit with Integrated High-Gain Antenna

AWAP05O-ZZ

AWAP05OM-ZZ

F1.1.0.0 E072004-R01

150xxxxxxxxA

Compliances

Federal Communication Commission Interference Statement

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause interference to

radio communications. It has been tested and found to comply with the limits for a Class A

computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to

provide reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference, in which case the user, at his own expense, will be required to take whatever

measures may be required to correct the interference. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance could void

your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or greater

for 10 Mbps connections, Category 5 for 100 Mbps connections.

Warnings: 1.Wear an anti-static wrist strap or take other suitable measures to prevent

electrostatic discharge when handling this equipment.

2.When connecting this device to a power outlet, connect the field ground

lead on the tri-pole power plug to a valid earth ground line to prevent

electrical hazards.

IMPORTANT NOTE: FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance

of 20 centimeters (8 inches) between the radiator and your body. This transmitter must

not be co-located or operating in conjunction with any other antenna or transmitter.

Wireless 5 GHz Band Statement:

As the access point can operate in the 5150-5250 MHz frequency band it is limited by the

FCC, Industry Canada and some other countries to indoor use only so as to reduce the

potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they have priority) of the

5250-5350 MHz and 5650-5850 MHz bands. These radars could cause interference and/

or damage to the access point when used in Canada.

The term “IC:” before the radio certification number only signifies that Industry Canada

technical specifications were met.

Safety Compliance

Power Cord Safety

Please read the following safety information carefully before installing the wireless

bridge:

Warning: Installation and removal of the unit must be carried out by qualified personnel

only.

• The unit must be connected to an earthed (grounded) outlet to comply with international

safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a

configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only remove

power from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected

also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT†supplies. If your supplies are of IT type, this unit

must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the

secondary connection point labelled Neutral, connected directly to earth (ground).

†Impédance à la terre

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A, 125

V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with a 5 A fuse

which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO.75

(minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO.75

(minimum).

IEC-320 receptacle.

iii

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le wireless

bridge:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un

personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il

n'y a pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de

respecter les normes internationales de sécurité.

• Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit

respecter une configuration qui permet un branchement sur une entrée d’appareil EN

60320/IEC 320.

• La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile.

Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique

au niveau de cette prise.

• L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à

la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il

est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos

alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une

tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec

un point secondaire de connexion portant l’appellation Neutre et avec raccordement

direct à la terre (masse).

Bitte unbedingt vor dem Einbauen des wireless bridges die folgenden

Sicherheitsanweisungen durchlesen:

WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal

erfolgen.

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la CSA.

Les spe'cifications minimales pour un cable flexible sont AWG No. 18, ouAWG No.

16 pour un cable de longueur infe'rieure a` 2 me'tres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre (mise à la

masse) et respecter la configuration NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P

(15 A, 250 V).

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de la norme DK2 1a

ou DK2 5a.

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011.

Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”)

LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type

HO3VVF3GO.75 (minimum).

• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen

werden.

• Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die

internationalen Sicherheitsnormen erfüllt.

• Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker) muß

einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.

• Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die

Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus

der Netzsteckdose unterbrochen werden.

• Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben,

wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen

betrieben werden.

Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.

Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung) sein und die

Aufschrift <HAR> oder <BASEC> tragen.

Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Contents

Chapter 1: Introduction 1-1

Package Checklist 1-2

Hardware Description 1-2

Integrated High-Gain Antenna 1-3

External Antenna Options 1-3

Ethernet Port 1-4

Power Injector Module 1-4

Receive Signal Strength Indicator (RSSI) BNC Connector 1-5

Grounding Point 1-5

Wall- and Pole-Mounting Bracket Kits 1-5

System Configuration 1-5

Features and Benefits 1-6

System Defaults 1-6

Chapter 2: Network Configuration 2-1

Access Point Topologies 2-1

Ad Hoc Wireless LAN (no Access Point or Bridge) 2-1

Infrastructure Wireless LAN 2-2

Infrastructure Wireless LAN for Roaming Wireless PCs 2-3

Bridge Link Topologies 2-4

Point-to-Point Configuration 2-4

Point-to-Multipoint Configuration 2-4

Chapter 3: Bridge Link Planning 3-1

Data Rates 3-1

Radio Path Planning 3-2

Antenna Height 3-3

Antenna Position and Orientation 3-4

Radio Interference 3-5

Weather Conditions 3-5

Ethernet Cabling 3-6

Grounding 3-6

Chapter 4: Hardware Installation 4-1

Testing Basic Link Operation 4-1

Mount the Unit 4-1

Using the Pole-Mounting Bracket 4-1

Using the Wall-Mounting Bracket 4-3

Connect External Antennas 4-4

Connect Cables to the Unit 4-5

Connect the Power Injector 4-5

Contents

Align Antennas 4-6

Chapter 5: Initial Configuration 5-1

Initial Setup through the CLI 5-1

Initial Configuration Steps 5-2

Using the Web-based Management Setup Wizard 5-3

Chapter 6: System Configuration 6-1

Advanced Configuration 6-1

System Identification 6-2

TCP / IP Settings 6-4

Radius 6-6

PPPoE Settings 6-8

Authentication 6-11

Filter Control 6-17

SNMP 6-19

Administration 6-22

System Log 6-25

Wireless Distribution System (WDS) 6-29

Bridge 6-30

Spanning Tree Protocol (STP) 6-33

Radio Interface 6-37

Radio Settings (802.11a) 6-38

Radio Settings (802.11g) 6-42

Security (Bridge Mode) 6-44

Security (Access Point Mode) 6-49

Status Information 6-60

AP Status 6-60

Station Status 6-62

Event Logs 6-64

Chapter 7: Command Line Interface 7-1

Using the Command Line Interface 7-1

Accessing the CLI 7-1

Telnet Connection 7-1

Entering Commands 7-2

Keywords and Arguments 7-2

Minimum Abbreviation 7-2

Command Completion 7-2

Getting Help on Commands 7-2

Partial Keyword Lookup 7-3

Negating the Effect of Commands 7-3

Using Command History 7-3

Understanding Command Modes 7-4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alfa Network Drahtloser Zugangspunkt Handbücher

Alfa Network

Alfa Network AWAP02O-86H Bedienungsanleitung

Alfa Network

Alfa Network AWAP601HW Bedienungsanleitung

Alfa Network

Alfa Network N2 Bedienungsanleitung

Alfa Network

Alfa Network AWAP608H Bedienungsanleitung

Alfa Network

Alfa Network SoLo51 Bedienungsanleitung

Alfa Network

Alfa Network AWAP02O-86 Bedienungsanleitung

Alfa Network

Alfa Network AWAP803 Bedienungsanleitung

Alfa Network

Alfa Network AWAP02O-1W Bedienungsanleitung

Alfa Network

Alfa Network AWAP411 Bedienungsanleitung

Alfa Network

Alfa Network AWAP601HW Bedienungsanleitung

Alfa Network

Alfa Network AWAP02O-1W Bedienungsanleitung

Alfa Network

Alfa Network AWAP02O-86 Bedienungsanleitung

Alfa Network

Alfa Network AWAP803 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung