Alfresco ALX2 Bedienungsanleitung

TOOLS REQUIRED TO INSTALL THIS KIT:

ITEM DESCRIPTION:

A SCREWDRIVER - PHILIPS SIZE # 2

B SCREWDRIVER - FLAT 1/8” WIDE TIP

C 7/8 in WRENCH - OPEN TYPE

D 9/16 in WRENCH - OPEN TYPE

E 1/2 in WRENCH - OPEN TYPE

F RATCHETING SOCKET WRENCH

G SOCKET EXTENSION DRIVER - 3 in.

H 1/2 in SOCKET

I 7/16 in SOCKET

J 10 mm SOCKET

K 7 mm SOCKET

TILT

FORWARD

ROTISSERIE

PANEL

3/8” GAS

TUBE

REPLACEMENT PROCEDURE:

ROTISSERIE ORIFICE:

STEP 1:

Remove all Grills, Warming Racks, Briquette Trays

and Grill Burners from the grill’s firebox.

STEP 2:

Detach the Rotisserie Panel by removing

the holding screws located at each top cor-

ner of the panel. (Note: ALX2-56 BFG units

have two separate panels - remove screws

from both panels)

STEP 3:

To access the burner’s orifice behind the

panel, “tilt” the panel forward. The panel can

be supported by the bottom tabs, as you tilt

the panel.

(See figure at right - ALX2-42 shown).

IMPORTANT: The Rotisserie Burner has a flexible,

stainless steel, 3/8” gas tube. Flex the tube forward slowly

towards you. (It’s quite strong).

ROTISSERIE

PANEL

1/2” OPEN

WRENCH

BURNER

ORIFICE

3/8”

ELBOW

FITTING GAS

LINE

REARHOODASSEMBLY

RATCHET

WRENCH

3” DRIVER

7 mm SOCKET

ORIFICE

GAS

VALVE

STEP 4:

Remove the Rotisserie orifice

with a 1/2” open wrench from the

3/8” compression elbow fitting.

Install the replacement orifice for

the proper fuel you are replacing.

(See orifice kits at the end of this

booklet).

Tighten the orifice to ensure no

leaks will occur.

IMPORTANT:

Verify that the igniter cable, located

opposite to the orifice assembly, is

properly secured before reassembly

of the panel.

STEP 5:

Reassemble the Rotisserie Panel by reversing the procedure. Tilt the panel backwards, and insert the

top back into the rear hood assembly. Fasten the top 2 screws at each end to secure the panel in place.

GRILL BURNER ORIFICES:

STEP 6:

Remove the gas Knobs from all the valves.

STEP 7:

Replace each of the U-Burner orifices for the proper

fuel you’ll be using on the valve stems. Use a 7 mm

socket, socket driver and ratchet wrench as shown at

right and below.

GRILL BURNER ORIFICES (SEARZONE™) :

STEP 7:

If your grill has a SearZone™ burner, use a ratcheting wrench, a 3” driver extender and a 1/2” socket,

remove the orifice from the inside of the grill. The SearZone™ orifice is located just below the burner’s

igniter electrode. The orifice is attached to a 3/8” elbow fitting directly in the firewall (between the front

panel and the firebox). It is not attached to the gas valve as the U-Burners. (Refer to the images below as a

reference).

DO NOT OVER TIGHTEN !

BACK VIEW SIDE VIEW

GAS

VALVE

ORIFICE 1/2”

SOCKET IGNITER

ELECTRODE

FIREWALL

3/8” ELBOW

FITTING GAS LINE TO

ORIFICE

SMOKER ORIFICE:

STEP 8:

Remove the Smoker Tray and Grease Tray Assem-

blies out of the grill’s body.

STEP 9:

Using a 7/16” open wrench, loosen the compression

fitting from the 1/8” aluminum smoker gas line. The

smoker orifice assembly is attached to the firewall

with one screw, remove it.

NOTE:The aluminum gas line is very soft. Carefully,

bend the gas line forward and remove the orifice as-

sembly. If the gas line is NOT free after loosening

the nut, continue to un-screw the nut until the as-

sembly is free to be removed. The nut along with the

compression ferrule will remain with the pipe. 7/16”

WRENCH

# 2 SCREW

DRIVER

SCREW

ORIFICE

ASSEMBLY 1/8” ALUM.

GAS LINE

(Smoker Orifice cont.)

STEP 10:

With the smoker orifice assembly removed, remove the

orifice using a 9/16” wrench (for the elbow’s body) and

a 7/16” for the orifice itself.

Replace with the proper fuel you’ll be using.

(Refer to the assembly at right as a guide)

STEP 11:

Reinstall the orifice assembly into the grill by following

these last 2 steps in reverse.

DO NOT over tighten the compression fitting to the

1/8” aluminum gas line.

ORIFICE

SMOKER ORIFICE ASSEMBLY

SUPPORT

PLATE

1/8” COMPRESSION

ELBOW FITTING

NOTE:

COMPRESSION FITTING MIGHT REMAIN

WITH 1/8” ALUMINUM GAS LINE

ORIFICE

10 mm

SOCKET

DRIVER

WRENCH

SIDE BURNERS: (ALX2-56 MODEL ONLY)

STEP 12:

Remove the side burners’ cover, cooking grate,

burner exterior and inner cap.

STEP 13:

Looking directly over the burner, locate and

remove the orifice from the bottom of the

cone-shaped burner body. Use a 10 mm

socket, driver extension and ratchet wrench

for this procedure.

STEP 14:

Replace the orifice with one for the proper fuel to be

used. DO NOT OVER TIGHTEN!

COVER

GRATE

EXTERNAL

CAP

INNER

CAP

GAS PRESSURE REGULATOR CONVESION:

STEP 15:

The ALX2 grill is equipped with a Maxitrol™ pressure regulator

that is suitable for LP or NG fuel regulation. To convert the

regulator to proper fuel, remove the brass cap located in it’s

center.

CAUTION: There are several components in this regulator as-

sembly. Be careful with the gas sealing washer, the plunger

and plunger’s spring located inside the regulator.

STEP 16:

Locate the black plastic plunger inside the brass cap. The plunger provides the right pressure setting at

the regulator outlet by changing the spring pressure.

Pull (pop-out) the plunger out of the brass cap, reverse it’s direction and re-insert into the cap with the

proper fuel desired pointing TOWARDS the regulator spring and body.

Reattach the brass cap into the regulator body and tighten securely with the gasket.

STEP 17:

If the unit is being converted from NG to LP, the LP kit will include a 1/2” NPT X 3/8” ODF reducer (hose

adapter) that needs to be installed on the gas inlet elbow attached to the regulator.

Install with reducer with a gas approved plumbing seal Teflon® paste or gas approved yellow Teflon®

tape.

NOTE: The conversion is now complete. Pressurize the gas line with the correct fuel for the application

and check for leaks before lighting up the grill. Before using the grill, all the grill’s surface burners will

need to be adjusted for proper combustion and low flame settings. Refer to the following steps for adjust-

ment.

BRASS

CAP GASKET PLUNGER

SPRING

REDUCER

PLUNGER DETAIL:

The plunger LP side has a WIDE

disk on the end. The NG (NAT) side

does not. The side pointing to the

body of the regulator determines

the fuel to be used in the grill.

AIR SHUTTER ADJUSTMENT:

Adjust the “AIR SHUTTER” to regulate the amount of air that enters into the burner for combustion.

Loosen the set-screw of the air shutter. Reinstall the burner. Make certain that the burners are sitting

properly on the orifices.

Light the burners and adjust according to the following directions:

1. Turn the valve on “HI”, light the burner and allow it to “WARM UP” for 10 minutes.

2. If the flame is yellow, indicating insufficient air, turn the air shutter to allow more air to

the burner.

3. If the flame is noisy and tends to lift away from the burner, indicating too much air, turn

the air shutter to reduce the amount of air to the burner.

LOW HEAT SETTING ADJUSTMENT:

NOTE:

ADJUST THE LOW HEAT SETTING

WHEN CHANGING FUELS OR WHEN

ALTITUDE OR OTHER ENVIRON-

MENTAL FACTORS ARE CAUSING

POOR, LOW HEAT, PERFORMANCE.

ADJUSTMENT STEPS:

1. Follow lighting instructions by setting the control

knob on “HI” and allow the burner to preheat for 10

minutes.

2. Turn the control knob to “LOW” and wait for the

burner temperature to drop and stabilize.

3. Attempting adjustment at any setting other than

LOW can create a dangerous condition.

4. Remove knob by pulling straight away from control

panel.

5. Insert a small blade (1/8” wide) screwdriver into the

valve stem to begin the adjustment.

6. Turn counter-clockwise to INCREASE the low heat

flame, or clockwise to DECREASE the blame height.

(see figure at right).

WARNING

NEVER ADJUST THE BURNER SO LOW THAT IT MAY

GO OUT DURING USE. DO NOT OPERATE THE

GRILL WITH THE LOW HEAT SCREW REMOVED.

GAS CAN ESCAPE AND CAUSE A POTENTIALLY

HAZARDOUS CONDITION.

LESS

FLAME

GAS VALVE

1/8” FLAT SCREWDRIVER

1”

MAX.

”

MAX.

FLAME SIZE

AIR SHUTTER

ADJUSTMENT

CUP

SET-SCREW

U-BURNER

Adjust the flames so the burner is fully lit around the perimeter when the knob is in the LOW position.

Do not adjust the burner flame so low that it may go out during use. Once proper adjustment is reached,

reattach the knob by pushing onto stem.

Your

Alfresco

™ Gourmet Grill is now ready for use with the new fuel.

Alfresco

™ ALX2 Grill Gas Supply

Conversion Instructions

Alfresco

™ Gourmet Grills

ALX2 GAS CONVERSION KIT NUMBERS

GRILL SIZE: NG TO LP LP TO NG

ALX2-30 (30SZ) 190-0048 190-0049

ALX2-42 / 56 (42SZ / 56SZ) 190-0050 190-0051

ALX2-56 BFG 190-0052 190-0053

Andere Handbücher für ALX2

Inhaltsverzeichnis

Andere Alfresco Grill Handbücher

Alfresco

Alfresco ALX2-42 SZ Bedienungsanleitung

Alfresco

Alfresco AGBQ-42 Bedienungsanleitung

Alfresco

Alfresco AGBQ-56BFG Bedienungsanleitung

Alfresco

Alfresco ALX2-30 Bedienungsanleitung

Alfresco

Alfresco AGBQ-30 Bedienungsanleitung

Alfresco

Alfresco AGBQ-30 Bedienungsanleitung

Alfresco

Alfresco ALX2-56 Bedienungsanleitung

Alfresco

Alfresco ALX2-42 Bedienungsanleitung

Alfresco

Alfresco ALX2-56 BFG Bedienungsanleitung

Alfresco

Alfresco ALX2-30 Leitfaden

Alfresco

Alfresco AGBQ-42 Bedienungsanleitung

Alfresco

Alfresco AGBQ-30 Leitfaden

Alfresco

Alfresco ALX2-56 Bedienungsanleitung

Alfresco

Alfresco ALX2-30 Bedienungsanleitung

Alfresco

Alfresco Kamado Bedienungsanleitung

Alfresco

Alfresco ALX2 Leitfaden

Alfresco

Alfresco AGBQ-30SZ Bedienungsanleitung

Alfresco

Alfresco VERSAPOWER Bedienungsanleitung

Alfresco

Alfresco AGBQ-30 Stücklistenhandbuch

Alfresco

Alfresco AGBQ-42SZ Bedienungsanleitung

Alfresco

Alfresco ALX2-56SZ BFG Bedienungsanleitung

Alfresco

Alfresco ALSB-2C Bedienungsanleitung

Alfresco

Alfresco G4ALF2BI Bedienerhandbuch

Alfresco

Alfresco ALX2-56 Bedienungsanleitung

Beliebte Grill Handbücher anderer Marken

Orbegozo

Orbegozo GR 2300 Bedienungsanleitung

bora

bora PT11 Bedienungsanleitung

Klarstein

Klarstein 10031664 Bedienungsanleitung

Garland

Garland MWE3W Bedienungsanleitung

Char-Broil

Char-Broil 463722714 Bedienungsanleitung

Nexgrill

Nexgrill 720-0830HK Bedienungsanleitung

Kenmore

Kenmore 415.16123800 Bedienungsanleitung

Camp Chef

Camp Chef PG24CLAU Bedienungsanleitung

Tucker Barbecues

Tucker Barbecues GTR Series Montageanleitung

Monogram

Monogram ZGG540NCP1SS Bedienungsanleitung

Equipex

Equipex Sodir Savoy Bedienungsanleitung

Gaggenau

Gaggenau VR 414 610 Bedienungsanleitung

Miele

Miele KM 408-1 Bedienungsanleitung

George Foreman

George Foreman GGR50B Bedienungsanleitung

AOG

AOG T series Bedienungsanleitung

Gorenje

Gorenje TG2000CB Bedienungsanleitung

Weber

Weber Genesis Silver-B Permamount NG 051701 Bedienungsanleitung

Glen

Glen SA 3037 Bedienungsanleitung