Allen-Bradley 2711P-RN6K Bedienungsanleitung

Installation Instructions

Communication Modules

Catalog Numbers 2711P-RN6, 2711P-RN6K, 2711P-RN15S, 2711P-RN15SK

About This Publication

This document provides instructions on how to install or replace a communication module on a

PanelView Plus 700, 1000, 1250, or 1500 terminal.

The communication module installs over the logic module. The installation is the same for all

communication modules regardless of communication type.

Additional Resources

You can view or download publications at

http://www.rockwellautomation.com/literature/. To order paper copies of technical

documentation, contact your local Rockwell Automation distributor or sales

representative.

Topic Page

Important User Information 2

Install a Communication Module 3

Install a Communication Module 4

Cat. No.(1)

(1) These installation instructions also apply to other cat. no. 2711P-RNxx communication modules.

Communication Conformal

Coated Marine

Certified

DH+ DH-485 Remote I/O(2)

(2) Only supported on PanelView Plus 700 to 1500 terminals running FactoryTalk View Machine Edition software,

version 5.1 or earlier.

ControlNet

2711P-RN6 • • • •

2711P-RN6K • • • •

2711P-RN15S • •

2711P-RN15SK • •

IMPORTANT The logic module must be attached to a PanelView Plus display module before you attach

the communication module.

Spare Allen-Bradley Parts

2Communication Modules

Rockwell Automation Publication 2711P-IN003D-EN-P - June 2010

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1

available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid-state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy

themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid

a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to

alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to

alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

Communication Modules 3

Rockwell Automation Publication 2711P-IN003D-EN-P - June 2010

Install a Communication Module

Follow these steps to install a new communication module.

1. Disconnect power from the terminal.

2. If the display module is removed from the panel, set the terminal, display side down, on a

clean, flat, stable surface.

3. Position the communication module over the logic module so that the connector on the

bottom of the communication module aligns with the connector on the logic module.

4. To prevent ESD between the modules, allow the communication module to touch the

logic module before making the connection.

WARNING: Explosion Hazard

Do not connect or disconnect any communication cable with power applied to

this device or any device on a network. An electrical arc could cause an

explosion in hazardous location installations. Be sure power is removed or the

area is known to be nonhazardous before proceeding.

ATTENTION: Work in a static-free environment and wear a properly grounded

electrostatic discharge (ESD) wristband. Do not touch the communication

module connector or its internal circuitry to avoid ESD.

TIP Logic module might look different depending on catalog number.

Connector for

Communication Module

Connector

Communication Module

Logic Module

Spare Allen-Bradley Parts

Rockwell Automation Publication 2711P-IN003D-EN-P - June 2010 PN-77996

Allen-Bradley, DH+, FactoryTalk View Machine Edition, PanelView Plus, Rockwell Software, and Rockwell Automation are trademarks of

Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

5. Push down on the communication module until the connectors are seated.

6. Tighten the four screws that

secure the communication

module to the logic module

to a torque of 0.58 N•m

(5…7 lb•in).

Replace a Communication Module

Follow these steps to replace a communication module.

1. Disconnect power from the terminal.

2. Disconnect communication cables from the module.

3. Remove the four screws that secure the communication module.

4. Carefully lift the communication module away from the logic module.

5. Install the new communication module by following steps 3…6 under Install a

Communication Module on page 3.

WARNING: Explosion Hazard

Do not connect or disconnect any communication cable with power applied to

this device or any device on a network. An electrical arc could cause an

explosion in hazardous location installations. Be sure power is removed or the

area is known to be nonhazardous before proceeding.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1336 PLUS II Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-OF8C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE8 Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1407-CGCM Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix SynchLink 1756-SYNCH Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock Series Handbuch

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O ControlNet 1794-ACN15 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-SN Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-PM Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-KT/B Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley 1769-ASCII Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SERCOS 1756-M03SE/A Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IXHR Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung