Allen-Bradley SERCOS 1756-M03SE/A Bedienungsanleitung

Publication 1756-IN572E-EN-P – March 2004

Installation Instructions

3, 8, or 16 Axis SERCOS interface Module

(Catalog Number/Series 1756-M03SE/A, 1756-M08SE/B, and

1756-M16SE/A)

The 3, 8, or 16 Axis SERCOS interface™ module mounts in a

ControlLogix™ chassis and uses fiber optical connections for all field-side

wiring.

Before you install your module you should have:

•installed and grounded a 1756 chassis and power supply.

•ordered and received the fiber optic cables for your application.

For: See page:

Important User Information 2

Overview 4

Determining the Power Requirements 5

Identifying Module Components 5

Module Product Label 8

Installing the Module 8

Fiber Optic Transmission 10

Fiber Optic Cables 11

Cable Connector Handling and Maintenance 14

Supported Drives 15

Ring Topology 17

Checking the LED Indicators 18

Removing the Module from the Chassis 21

Module Specifications 22

Hazardous Location Information 26

Rockwell Automation Support Back Cover

Allen-Bradley PLCs

23, 8, or 16 Axis SERCOS interface Module

Publication 1756-IN572E-EN-P – March 2004

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application, Installation and

Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell

Automation sales office or online at http://www.ab.com/manuals/gi) describes some

important differences between solid state equipment and hard-wired electromechanical

devices. Because of this difference, and also because of the wide variety of uses for solid

state equipment, all persons responsible for applying this equipment must satisfy

themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes.

Because of the many variables and requirements associated with any particular installation,

Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on

the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of

information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission

of Rockwell Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or

death, property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and

understanding of the product.

ATTENTION Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help

you:

•identify a hazard

•avoid a hazard

•recognize the consequence

SHOCK HAZARD Labels may be located on or inside the drive to alert people that dangerous

voltage may be present.

3, 8, or 16 Axis SERCOS interface Module 3

Publication 1756-IN572E-EN-P – March 2004

Related Documentation

The following documents contain additional information concerning related

Allen-Bradley products. To obtain a copy, contact your local Rockwell

Automation office or distributor.

BURN HAZARD Labels may be located on or inside the drive to alert people that surfaces may

be dangerous temperatures.

For: Read This Document: Publication

Number

ControlLogix motion commands Motion Instruction Set

Reference Manual

1756-RM007

Information on setup and

configuration

ControlLogix Motion

Module Setup and

Configuration manual

1756-UM006

Information on installation, wiring,

and setup for the 1394C-SJTxx-D

1394 SERCOS Interface

Multi Axis Motion Control

System

1394C-5.20

Information on integrating the 1394

drive with SERCOS

1394 SERCOS Integration

Manual

1394-IN024

Information on Ultra3000 installation Ultra3000 Hardware

Installation Manual

2098-IN003

Information on Kinetix 6000 Module

installation

Kinetix 6000 Module

Installation Manual

2094-IN004

Information on Kinetix 6000

installation

Kinetix 6000 Installation

Manual

2094-IN001

Information on integrating the Kinetix

6000 with SERCOS

Kinetix 6000 Integration

Manual

2094-IN002

Information on integrating the

Ultra3000 with the 1756-M08SE

Ultra3000 SERCOS

Integration Manual

2098-IN005

Information on use of the 8720MC

High Performance Drive

8720MC High Performance

Drive User Manual

8720MC-UM001

Important User Information

Allen-Bradley PLCs

43, 8, or 16 Axis SERCOS interface Module

Publication 1756-IN572E-EN-P – March 2004

Overview

The 3, 8, or 16 Axis SERCOS interface module serves as a link between the

ControlLogix platform and intelligent drives. The communication link

between the module and the drive(s) is via IEC/EN 61491 SErial Real-time

COmmunication System (SERCOS) using fiber optic medium. Fiber optics

assures reliable high speed data transmission with excellent noise immunity,

improved performance, and elimination of interconnect wiring.

SERCOS is a real-time optical serial interface between the control unit and its

associated drives to transmit periodic and non-periodic data. Its topology is

that of a ring with one master and multiple slaves (axes). The 3, 8 or 16 Axis

SERCOS interface module serves as the interface between one ControlLogix

processor and 1 to 3 axes for the 1756-M03SE, 1 to 8 axes for the

1756-M08SE, and 1 to 16 axes for the 1756-M16SE operating in either

position, velocity, or torque mode. The module has a programmable ring

Cycle Period of 0.5ms, 1ms or 2ms depending on the number of axes and a

ring Data Rate of 4 Mbaud or 8 Mbaud. The module is designed to meet the

Control and Information Protocol (CIP) common specification.

Preventing Electrostatic Discharge

ATTENTION This equipment is sensitive to electrostatic discharge,

which can cause internal damage and affect normal

operation. Follow these guidelines when you handle

this equipment:

•Touch a grounded object to discharge potential

static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component

boards.

•Do not touch circuit components inside the

equipment.

•If available, use a static-safe workstation.

•When not in use, store the equipment in

appropriate static-safe packaging.

3, 8, or 16 Axis SERCOS interface Module 5

Publication 1756-IN572E-EN-P – March 2004

Removing and Inserting Under Power (RIUP)

This module is designed so you can remove and insert it under backplane

power and field-side power.

Repeated electrical arcing causes wear to contacts on both the module and its

mating connector. Worn contacts may create electrical resistance that can

affect module operation.

This equipment is classified as open equipment and must be installed

(mounted) in an enclosure during operation as a means of providing safety

protection.

Determining the Power Requirements

This module receives power from the 1756 chassis power supply and requires

two sources of power: 760 mA at 5.1V and 2.5 mA at 24V from the

backplane. Add this current to the requirements of all other modules in this

chassis to prevent overloading the backplane power supply.

Identifying Module Components

The following diagrams provide two views of the module. The first diagram is

a front view which shows the position and function of the LEDs and the

icons for the receiver and transmitter. The second diagram is a side view

which shows the position of the transmitter and receiver connectors. (The

1756-M03SE and the 1756-M16SE look identical to the 1756-M08SE.)

WARNING When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations. Be sure

that power is removed or the area is nonhazardous

before proceeding.

Allen-Bradley PLCs

63, 8, or 16 Axis SERCOS interface Module

Publication 1756-IN572E-EN-P – March 2004

Figure 1 Front View of the Module

Receiver

SERCOS Connector

(front & rear)

Transmitter Icon

Receiver Icon

SERCOS Ring

Status

Status LEDs

Module Health &

Communication Status

Tx (rear)

Rx (front)

SERCOS

Communication

Phase

SERCOS interface

3, 8, or 16 Axis SERCOS interface Module 7

Publication 1756-IN572E-EN-P – March 2004

Figure 2 Side View of the Module Showing Fiber Optic Cable Connections

The end of the cable is inserted into the appropriate connector of the

1756M03SE, 1756-M08SE, or 1756-M16SE. The threaded portion of the

cable connector assembly fits over the module connector and is screwed on

finger tight. Make sure that you remove the protector end caps before

Transmitter

Receiver

Allen-Bradley PLCs

83, 8, or 16 Axis SERCOS interface Module

Publication 1756-IN572E-EN-P – March 2004

attaching cable to the module. The end of the cable that emits light is the

transmitter.

The Module’s Product Label

The following figure shows the product label that is affixed to the side of the

1756-M03SE, 1756-M08SE, and 1756-M16SE modules. The three modules

look very much alike and checking the label carefully is the only way to be sure

that you have the correct module. Pay particular attention to the CAT. NO.

SERIES field on the label. This field indicates whether you have a

1756-M03SE, 1756-M08SE, or 1756-M16SE module and also the series of

the module. The label contains additional information about the module and

should be thoroughly checked prior to installation to ensure that the product

matches your expectations.

Figure 3 1756-M08SE Product Label

Installing the Module

To install the 3, 8, or 16 Axis SERCOS interface module:

A-B Catalog Number

and Series

Product Name

Certifications

Ratings

Series and Firmware

version Information

Power Requirements

A-B Part Number

Date of Manufacture

Catalog

Revision

3, 8, or 16 Axis SERCOS interface Module 9

Publication 1756-IN572E-EN-P – March 2004

1. Align the module circuit board with the top and bottom chassis guides

Figure 4 Align Module

POWE

Printed circuit

board

SERCOS interface

Allen-Bradley PLCs

10 3, 8, or 16 Axis SERCOS interface Module

Publication 1756-IN572E-EN-P – March 2004

2. Push evenly and firmly to seat the module in the chassis. It is seated

when the top and bottom locking tabs have snapped into place.

Figure 5 Seat the Module

Fiber Optic Transmission

The fiber optic transmitter for the SERCOS interface 3, 8, or 16 Axis module

uses a 650nm wavelength. This produces a visible light from the port and is a

determinant in factoring maximum cable lengths. The high light output lets

you use both plastic optical fiber (POF) and Hard Clad Silica (HCS®) cables.

The fiber optics used with the 1756-M03SE, 1756-M08SE and 1756-M16SE

modules are rated Class 1 for IEC Laser (LED) Safety Classification. Be aware

that under certain conditions, viewing the optical port may expose the eye to

hazard. Under most viewing conditions, there is no eye hazard.

ATTENTION When viewed under some conditions, the optical port

may expose the eye beyond the maximum permissible

exposure recommended in ANSI Z136.2, 1993.

WER

Locking

tab

SERCOS interface

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1771-KA2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet Ex 1797-RPA Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DHRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711P-RN6K Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ASCII Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-AIFM16-F-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-OB16M12R Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1770-KFDG Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-OB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ProcessLogix B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-ODD Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBDS Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-KT/B Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley MSR41 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-IFM40F-3 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732D A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1203 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micrologix 1500 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung