Allen-Bradley ArmorBlock 1732E-8IOLM12R Bedienungsanleitung

Installation Instructions

ArmorBlock I/O 8 Channel IO-Link

Master Module

Catalog number 1732E-8IOLM12R

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

Additional Resources 4

About the Module 4

Install the Module 6

Mount the Module 7

Connect the I/O, Network and Auxiliary Cables to the Module 9

Configure the Module 11

Interpret LED Indicators 13

Specifications 15

2ArmorBlock I/O 8 Channel IO-Link Master Module

Publication 1732E-IN001A-EN-E - July 2016

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ArmorBlock I/O 8 Channel IO-Link Master Module 3

Publication 1732E-IN001A-EN-E - July 2016

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in overvoltage Category II

applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft)

without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR 11. Without appropriate precautions, there may be difficulties with

electromagnetic compatibility in residential and other environments due to

conducted and radiated disturbances.

This equipment is supplied as enclosed equipment. It should not require

additional system enclosure when used in locations consistent with the

equipment Enclosure Type Ratings. Subsequent sections of this publication may

contain more information regarding specific enclosure type ratings, beyond what

this product provides, that are required to comply with certain product safety

certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for additional install requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the

degrees of protection provided by different types of enclosure.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION: To comply with UL restrictions, this equipment and all connected

I/O must be powered from a source compliant with the following:

Safety Extra Low Voltage (SELV)

ATTENTION: To comply with CE Low Voltage Directive (LVD), this equipment

and all connected I/O must be powered from a source compliant with the

following: Safety Extra Low Voltage (SELV)

4ArmorBlock I/O 8 Channel IO-Link Master Module

Publication 1732E-IN001A-EN-E - July 2016

Additional Resources

If you would like a manual, you can:

• download a free electronic version from the internet:

http://literature.rockwellautomation.com

• purchase a printed manual by contacting your local Allen-Bradley distributor or

Rockwell Automation representative

About the Module

The ArmorBlock I/O 8 Channel IO-Link Master Module provides eight channels that

can be individually configured as IO-Link master or as a standard digital I/O module. The

IO-Link channel master module can be configured to fit any IO-Link and/or discrete

application.

In IO-Link mode, the module supports eight channels for IO-Link master

communication with IO-Link compatible devices. In standard digital I/O mode, the

module supports eight channels of digital input or output. Standard digital input channels

support IEC61131-2 type 1 input. Channels can also be disabled if not in use.

You must use this module with RSLogix™ 5000/Studio 5000® software, version 20 or later.

Use this diagram to identify the external features of the module.

Resource Description

ArmorBlock IO-Link Master Module Wiring

Diagrams 1732E-WD008 Pinout guide wiring diagram for the ArmorBlock

IO-Link Master module.

ArmorBlock 8 Channel IO-Link Master Module

User Manual 1732E-UM007 A detailed description of module functionality,

configuration, installation procedure and

information on how to use the ArmorBlock I/O

8 Channel IO-Link Master Module.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1.More information on proper wiring and grounding

techniques.

ArmorBlock I/O 8 Channel IO-Link Master Module 5

Publication 1732E-IN001A-EN-E - July 2016

Module Identification

Description Description

1 EtherNet/IP D-code M12 connector 8 Auxiliary power indicator

2 Function earth(1)

(1) Functional Earth grounds the I/O block’s EtherNet/IP communication circuitry which is designed to mitigate the effect of

noise on the network. The device requires a solid earth ground connection, either through a metal screw to a grounded

metal panel or through a wire. refer to EtherNet/IP Connector on page 10 for connections.

9 Micro-style power out

3 EtherNet/IP D-code M12 connector 10 Micro-style power in

4 Link 2 status indicator 11 Channel I/O or digital I/O status indicators

5 Network status indicator 12 Module status indicator

6 Node address switches 13 Link 1 status indicator

7 Micro-style I/O connectors

45871

6ArmorBlock I/O 8 Channel IO-Link Master Module

Publication 1732E-IN001A-EN-E - July 2016

Install the Module

To install the module:

• Set the network address.

•Mountthemodule.

• Connect the I/O, Network and Auxiliary cables to the module.

Set the Network Address

The I/O block ships with the rotary switches set to 999 and DHCP enabled.

To change the network address, you can do one of the following:

• adjust the switch on the front of the module.

• use a Dynamic Host Configuration Protocol (DHCP) server, such as Rockwell

Automation BootP/DHCP.

• retrieve the IP address from nonvolatile memory.

The I/O block reads the switches first to determine if the switches are set to a valid

number. To set the network address:

1. Remove power.

2. Remove the switch dust caps.

3. Rotate the three (3) switches on the front of the module using a small blade

screwdriver.

4. Line up the small notch on the switch with the number setting you wish to use.

Valid settings range from 001…254.

5. Replace switch dust caps. Make sure not to over tighten.

6. Reapply power.

ArmorBlock I/O 8 Channel IO-Link Master Module 7

Publication 1732E-IN001A-EN-E - July 2016

Set Network Address

When the switches are set to a valid number, the I/O block’s IP address is 192.168.1.xxx

(where xxx represents the number set on the switches). The I/O block’s subnet mask is

255.255.255.0 and the gateway address is set to 0.0.0.0. When the I/O block uses the

network address set on the switches, the I/O block does not have a host name assigned to it

or use any Domain Name Server.

If the switches are set to an invalid number (for example, 000 or a value greater than 254

excluding 888), the I/O block checks to see if DHCP is enabled. If DHCP is enabled, the

I/O block asks for an address from a DHCP server. The DHCP server also assigns other

Transport Control Protocol (TCP) parameters.

If DHCP is not enabled, the I/O block uses the IP address (along with other TCP

configurable parameters) stored in nonvolatile memory.

Mount the Module

Two sets of mounting holes are used to mount the module directly to a panel or machine.

Mounting holes accommodate #8 (M4) pan head screws. The torque specification is 0.68

Nm (6 lb-in.).

Example shows default

node address set at 163.

44233

Note: You need to remove the

protective switch dust caps before

you can adjust the address settings.

8ArmorBlock I/O 8 Channel IO-Link Master Module

Publication 1732E-IN001A-EN-E - July 2016

Product Dimensions

Refer to the mounting dimensions illustration to help you mount the module.

Module Dimensions

25.6

(1.01)

166.5 (6.56)

32 (1.26)

Side Mounting

32 (1.26 )

43.3 (1.70)

Front Mounting

18 (0.71)

37 (1.46)

16.2 (0.64)

166.5 (6.56)

179 (7.05)

Measurements are in millimeters (inches)

45765

ArmorBlock I/O 8 Channel IO-Link Master Module 9

Publication 1732E-IN001A-EN-E - July 2016

Mount the Module in High Vibration Areas

If you mount the module in an area that is subject to shock or vibration, we recommend

you use a flat and a lock washer to mount the module. Mount the flat and the lock washer

as shown in the mounting illustration. Torque the mounting screws to 0.68 Nm (6 lb-in.).

High Vibration Area Mounting

Connect the I/O, Network and Auxiliary Cables to the Module

The 1732E-8IOLM12R ArmorBlock EtherNet/IP module has a 5-pin micro-style I/O

connectors. We provide caps to cover the unused connectors on your module. Connect the

quick-disconnect cord sets you selected for your module to the appropriate ports.

I/O Connectors

Micro-style 5-Pin I/O Female Connector

45768

Lock washer

Flat washer

43853

(View into connector)

Pin 1 Sensor source voltage

Pin 2 IO-Link, Input/output B

Pin 3 Return

Pin 4 IO-Link, Input/output A

Pin 5 PE

10 ArmorBlock I/O 8 Channel IO-Link Master Module

Publication 1732E-IN001A-EN-E - July 2016

EtherNet/IP Connector

D-Code Micro Network Female Connector

IMPORTANT

Use the 1585D–M4DC–H: Polyamide small body unshielded mating

connectors for the D-Code M12 female network connector.

Note that the distance between the center of each Ethernet connector is

16.2 mm (refer to Module Dimensions on page 8). Rockwell Automation

recommends the use of suitable cable based on this measurement. Some of

the recommended cables are 1585D-M4TBJM-x and 1585D-M4TBDM-x

for daisychains.

IMPORTANT

Use two twisted pair CAT5E UTP or STP cables

(View into connector 1)

Pin 1 M12_Tx+

Pin 2 M12_Rx+

Pin 3 M12_Tx-

Pin 4 M12_Rx-

Pin 5 Connector shell shield GND

44808

(View into connector 2)

Pin 1 M12_Rx+

Pin 2 M12_Tx+

Pin 3 M12_Rx-

Pin 4 M12_Tx-

Pin 5 Connector shell shield GND

D-Code

M12 Pin

Wire Color Signal 8-wayModular

RJ45 Pin

1 White-orange TX+ 1

2 White-green RX+ 3

3 Orange TX- 2

4GreenRX- 6

Andere Handbücher für ArmorBlock 1732E-8IOLM12R

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley SLC 5/02 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-H Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732D A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-SN Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OFE Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ASCII Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Bedienungsanleitung

Allen-Bradley

Allen-Bradley Logix5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley DF1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley CAB6-HA 2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-HSCE Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-ACN15 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Handbuch

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE8H Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 PLUS II Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung