Allen-Bradley ArmorStart 290E Bedienungsanleitung

ArmorStart® LT Distributed Motor Controller

Catalog Numbers 290E, 291E, 294E

User Manual

Important User Information

Because of the variety of uses for the products described in this publication, those responsible for the application and use of

this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and

use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this guide are intended solely for purposes of

example. Since there are many variables and requirements associated with any particular installation, Rockwell Automation

does not assume responsibility or liability (to include intellectual property liability) for actual use based upon the examples

shown in this publication.

Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety

Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your

local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some

important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference,

and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the

use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

Rockwell Automation Publication 290E-UM001B-EN-P - June 2012 3

General Precautions

In addition to the precautions listed throughout this manual, the following statements, which are general to the system,

must be read and understood.

Precautions for Bulletin 294E Applications

ATTENTION: This manual is intended for qualified service personnel responsible for setting up and servicing these devices. The

user must have previous experience with and a basic understanding of electrical terminology, configuration procedures,

required equipment, and safety precautions.

WARNING: The National Electrical Code (NEC), NFPA79, and any other governing regional or local code will overrule the

information in this manual. Rockwell Automation cannot assume responsibility for the compliance or proper installation of the

ArmorStart LT or associated equipment. A hazard of personal injury and/or equipment damage exists if codes are ignored

during installation.

ATTENTION: The controller contains ESD (electrostatic discharge) sensitive parts and assemblies. Static control precautions are

required when installing, testing, servicing, or repairing the assembly. Component damage may result if ESD control

procedures are not followed. If you are not familiar with static control procedures, refer to Publication 8000-4.5.2, Guarding

against Electrostatic Discharge, or any other applicable ESD protection handbooks.

ATTENTION: Only personnel familiar with the controller and associated machinery should plan or implement the installation,

startup, and subsequent maintenance of the system. Failure to do this may result in personal injury and/or equipment

damage.

ATTENTION: Only qualified personnel familiar with adjustable frequency AC drives and associated machinery should plan or

implement the installation, startup, and subsequent maintenance of the system. Failure to do this may result in personal injury

and/or equipment damage.

4Rockwell Automation Publication 290E-UM001B-EN-P - June 2012

Software Requirements

The table lists the versions of software that are required.

Additional Resources

These documents and websites contain additional information concerning related Rockwell Automation products.

You can view or download publications at http:/www.rockwellautomation.com/literature/. To order paper copies of

technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Table 1 - Rockwell Automation Industrial Network Resources

Software Version

RSLinx Classic 2.56 or later

RSLogix 5000 17.01 or later

Download the most current version of the Add-On Profile from

http://www.rockwellautomation.com/support/downloads.html.

BOOTP/DHCP Version 2.3 or later

Resource Description

http://ab.rockwellautomation.com/Networks-and-Communications Rockwell Automation networks and communication website

http://ab.rockwellautomation.com/Networks-and-Communications/Ethernet-IP-

Network

Rockwell Automation EtherNet/IP website

http://www.rockwellautomation.com/services/networks/

http://www.rockwellautomation.com/services/security/

Rockwell Automation network and security services websites

http://www.ab.com/networks/architectures.html Education series webcasts for IT and controls professionals

EtherNet/IP Embedded Switch Technology Application Guide, Publication ENET-AP005 Describes how to install, configure, and maintain linear and device-level Ring (DLR)

networks using Rockwell Automation EtherNet/IP devices with embedded switch

technology.

EtherNet/IP Network Configuration User Manual, Publication ENET-UM001 Describes how to configure and use EtherNet/IP communication modules with a

Logix5000 controller and communicate with various devices on the Ethernet network.

EtherNet Design Consideration, Publication ENET-RM002A-EN-P Provides details on ethernet design and infrastructure.

EtherNet/IP Modules in Logix5000 Control Systems User Manual, Publication ENET-UM001 Provides details about how to configure your module.

EtherNet/IP Embedded Switch Technology Application Guide, Publication ENET-AP005 Provides information about using products with embedded switch technology to

construct networks with linear and ring topologies.

EtherNet/IP Industrial Protocol White Paper, Publication ENET-WP001 Describes how to implement services and data objects on a TCP/UDP/IP based Ethernet

network.

Industrial Automation Wiring and Grounding Guidelines, Publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.

Wiring and Grounding Guidelines, (PWM) AC Drives, Publication DRIVES-IN001 Describes wiring and grounding guidelines for Pulse Width Modulated (PWM) AC Drives

Product Certifications website,

http://www.rockwellautomation.com/products/certification/

Provides declarations of conformity, certificates, and other certification details.

Rockwell Automation Publication 290E-UM001B-EN-P - June 2012 5

Table 3 - Product Selection Resources

Rockwell Automation Support

Rockwell Automation provides technical information on the Web to assist you in using its products. At

http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical

and application notes, sample code and links to software service packs, and a MySupport feature that you can customize

to make the best use of these tools.

Installation Assistance

If you experience a problem within the first 24 hours of installation, contact Customer Support.

Table 2 - ODVA Resources

Resource Description

http://www.odva.org/ Open DeviceNet Vendors Association (ODVA) website

http://www.odva.org/default.aspx?tabid=54 The CIP Advantage website

•CIP features and benefits

•How to get started

Ethernet Media Planning and Installation Manual, ODVA publication

http://www.odva.org/Portals/0/Library/Publications_Numbered/

PUB00148R0_EtherNetIP_Media_Planning_and_Installation_Manual.pdf

Describes the required media components and how to plan for, install, verify,

troubleshoot, and certify an Ethernet network.

Network Infrastructure for EtherNet/IP: Introduction and Considerations, ODVA publication

http://www.odva.org/Portals/0/Library/Publications_Numbered/

PUB00035R0_Infrastructure_Guide.pdf

Provides an overview of the technologies used in EtherNet/IP networks and provides

guidelines for deploying infrastructure devices in EtherNet/IP networks.

Resource Description

Industrial Controls catalog website,

http://www.ab.com/catalogs/

Industrial Controls catalog website

ArmorStart LT Distributed Motor Controller Selection Guide, Publication 290-SG001 Product selection guide

Table 4 - Cisco and Rockwell Automation Alliance Resources

Resource Description

http://www.ab.com/networks/architectures.html Rockwell Automation and Cisco Systems reference architecture website

Converged Plantwide Ethernet (CPwE) Design and Implementation Guide, Publication

ENET-TD001

Represents a collaborative development effort from Rockwell Automation and Cisco

Systems. The design guide is built on, and adds to, design guidelines from the Cisco

Ethernet-to-the-Factory (EttF) solution and the Rockwell Automation Integrated

Architecture. The design guide focuses on the manufacturing industry.

United States or Canada 1.440.646.3434

Outside United States or

Canada

Use the Worldwide Locator at http://www.rockwellautomation.com/support/

americas/phone_en.html, or contact your local Rockwell Automation representative.

6Rockwell Automation Publication 290E-UM001B-EN-P - June 2012

New Product Satisfaction Return

Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the

manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures.

United States Contact your distributor. You must provide a Customer Support case number (call the

phone number above to obtain one) to your distributor to complete the return process.

Outside United States Please contact your local Rockwell Automation representative for the return

procedure.

Rockwell Automation Publication 290E-UM001B-EN-P - June 2012 7

Summary of Changes

New and Updated

Information

This table contains the changes made to this revision.

Topic Page

Added source brake and IPS specifications Various

8Rockwell Automation Publication 290E-UM001B-EN-P - June 2012

Summary of Changes

Notes:

Rockwell Automation Publication 290E-UM001B-EN-P - June 2012 9

Preface

European Communities (EC)

Directive Compliance

If this product has the CE mark it is approved for installation within the

European Union and European Economic Area (EEA). It has been designed and

tested to meet the following directives.

Low Voltage and EMC

Directives

This product is tested to meet the European Union (EU) Council 2006/95/EC

Low Voltage Directive and the EU Council 2004/108/EC Electromagnetic

Compatibility (EMC) Directive by applying the following standard(s):

•Bulletin 290E_/291E_: EN 60947-4-1 — Low-voltage switchgear and

controlgear — Part 4-1: Contactors and motor-starters — Electromechanical

contactors and motor-starters.

•Bulletin 294E_: EN 61800-3 — Adjustable speed electronic power drive

systems — Part 3: EMC product standard including specific test methods

EN 61800-5-1:2003 — Adjustable speed electrical power drive systems —

Part 5-1: Safety requirements — Electrical, thermal and energy.

This product is intended for use in an industrial environment.

10 Rockwell Automation Publication 290E-UM001B-EN-P - June 2012

Preface

Introduction The ArmorStart LT is an integrated, pre-engineered, motor starting solution

designed for use in material handling applications. ArmorStart LT is the latest

addition to the ArmorStart portfolio. ArmorStart LT is a leader in the market

place given its compact size and high performance features in network, I/O, and

motor control. This manual will guide you through the features and functionality

when installing the product. Thank you for choosing ArmorStart LT for your

distributed motor control needs. If you have any questions please refer to the

“Support Section” for contact information.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley ControlLogix System 1756-L1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Gebrauchsanweisung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ProcessLogix 1757-PLX52 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro830 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-2/20 Einrichtungshandbuch

Allen-Bradley

Allen-Bradley PanelView 800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2080-LC20-20QBB Bedienungsanleitung

Allen-Bradley

Allen-Bradley Guard Master MSR22LM Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardLogix 5570 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 IMPACT Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755TL Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-L30ERM Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40P Bedienungsanleitung

Allen-Bradley

Allen-Bradley Pico 1760-L12AWA Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch