Allen-Bradley ControlLogix 1756-STRT3 Gebrauchsanweisung

ControlLogix

Starter Kit

1756-STRT3

Quick Start Manual

Allen-Bradley Parts

Important User Information

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of these

products must satisfy themselves that all necessary steps have been

taken to assure that each application and use meets all performance

and safety requirements, including any applicable laws, regulations,

codes and standards. In no event will Allen-Bradley be responsible or

liable for indirect or consequential damage resulting from the use or

application of these products.

Any illustrations, charts, sample programs, and layout examples

shown in this publication are intended solely for purposes of

example. Since there are many variables and requirements associated

with any particular installation, Allen-Bradley does not assume

responsibility or liability (to include intellectual property liability) for

actual use based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation and Maintenance of Solid-State Control

(available from your local Allen-Bradley office), describes some

important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole

or part, without written permission of Rockwell Automation, is

prohibited.

Throughout this publication, notes may be used to make you aware of

safety considerations. The following annotations and their

accompanying statements help you to identify a potential hazard,

avoid a potential hazard, and recognize the consequences of a

potential hazard:

WARNING

Identifies information about practices or

circumstances that can cause an explosion in a

hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

ATTENTION

Identifies information about practices or

circumstances that can lead to personal injury or

death, property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

-Q

A-

-E

N-

-P

t Page 3

Table of Contents

WELCOME TO CONTROLLOGIX CONTROLLER QUICK START: ABOUT THE EXERCISES ____________________7

ABOUT THE CONTROLLOGIX PLATFORM _________________________________________________7

ABOUT THE FLEXLOGIX PLATFORM_____________________________________________________8

ABOUT THE COMPACTLOGIX PLATFORM _________________________________________________8

ABOUT THE SOFTLOGIX PLATFORM_____________________________________________________8

BEFORE YOU BEGIN ________________________________________________________________9

DOCUMENT CONVENTIONS ___________________________________________________________9

INSTALLING THE HARDWARE _____________________________________________________________10

INSTALLING THE RSLOGIX 5000 PROGRAMMING SOFTWARE _____________________________________10

EXERCISE 1: CREATING A NEW CONTROLLER FILE AND CONFIGURING YOUR I/O ______________________11

LAUNCHING RSLOGIX 5000 PROGRAMMING SOFTWARE ____________________________________11

CREATING A NEW CONTROLLER FILE __________________________________________________12

EDITING THE MAIN ROUTINE _________________________________________________________14

VERIFYING THE PROPERTIES FOR THE MAIN TASK AND THE MAIN PROGRAM______________________19

CONFIGURING YOUR I/O ____________________________________________________________22

CONFIGURING THE DISCRETE OUTPUT MODULE___________________________________________22

VIEWING TAGS ___________________________________________________________________24

CONFIGURING THE DISCRETE INPUT MODULE_____________________________________________26

VERIFYING TAG CREATION __________________________________________________________27

MAPPING I/O POINTS TO TAGS _______________________________________________________27

EXERCISE 2: CONFIGURING YOUR COMMUNICATIONS DRIVER, VERIFYING COMMUNICATIONS, DOWNLOADING YOUR PROGRAM,

CREATING A NEW TASK, PROGRAM, AND ROUTINE, AND CREATING AN ARRAY OF COUNTERS ____________29

LAUNCHING RSLINX SOFTWARE ______________________________________________________29

ADDING THE RS232-DF1 DRIVER_____________________________________________________30

VERIFYING COMMUNICATIONS TO THE CONTROLLER _______________________________________32

DOWNLOADING THE PROGRAM USING THE RS-232 DF1 DRIVER ______________________________35

CREATING A NEW PERIODIC TASK_____________________________________________________36

CREATING A NEW PROGRAM_________________________________________________________37

CREATING A NEW ROUTINE__________________________________________________________37

CREATING AN ARRAY OF COUNTERS ___________________________________________________39

Allen-Bradley Parts

-Q

A-

-E

N-

-P

t Page 4

EXERCISE 3: EDITING AND TESTING YOUR ROUTINES, PROGRAMS, AND TASKS _______________________41

EDITING AND TESTING YOUR ROUTINE__________________________________________________41

CREATING A TREND TO MONITOR THE CTU ACCUM VALUE __________________________________44

TESTING YOUR PROGRAM – PERIODIC TASK _____________________________________________47

EXERCISE 4: DEMONSTRATING REUSABLE CODE______________________________________________49

OPENING TWO SESSIONS OF RSLOGIX 5000_____________________________________________49

COPYING THE MAIN PROGRAM AND PASTING REUSABLE CODE _______________________________49

CHANGING THE NAME OF THE PROGRAM YOU PASTED______________________________________50

CHANGING THE NAME OF THE MAIN ROUTINE_____________________________________________50

MAPPING THE TAGS _______________________________________________________________51

REVIEWING THE STEPS FOR REUSING EXISTING CODE ______________________________________52

EXERCISE 5: DEMONSTRATING IMPORT-EXPORT CAPABILITIES ___________________________________53

EXAMINING THE CONTROLLER FILE ____________________________________________________53

EXPORTING THE CONTROLLER FILE ____________________________________________________54

REVIEWING THE EXPORT FILE FORMAT _________________________________________________54

IMPORTING THE CHANGED EXPORT FILE ________________________________________________54

VERIFYING YOUR CHANGES IN THE IMPORTED FILE ________________________________________55

IMPORTING TAGS FROM A .CSV FILE __________________________________________________55

EXERCISE 6: DEMONSTRATE DISCRETE DIAGNOSTIC I/O CAPABILITIES _____________________________57

OPENING THE CONTROLLER FILE AND SAVING IT AS A NEW FILE_______________________________57

LOOKING AT THE PROPERTIES OF THE OUTPUT MODULE ____________________________________57

CONFIGURING MODULE OUTPUT STATES AND DIAGNOSTICS _________________________________59

VIEWING THE TAGS CREATED FOR THE OUTPUT MODULE____________________________________61

LOOKING AT THE PROPERTIES OF THE INPUT MODULE ______________________________________63

VERIFYING THE 1756-OB16E DIAGNOSTICS _____________________ERROR! BOOKMARK NOT DEFINED.

EXERCISE 7: CONFIGURING AND TESTING ANALOG I/O MODULES _________________________________65

OPENING THE CONTROLLER FILE AND SAVING IT AS A NEW FILE_______________________________65

CONFIGURING THE ANALOG OUTPUT MODULE ____________________________________________65

VERIFYING TAGS__________________________________________________________________70

CONFIGURING THE ANALOG INPUT MODULE______________________________________________71

VERIFYING TAGS__________________________________________________________________74

ADDING LADDER LOGIC ____________________________________________________________75

-Q

A-

-E

N-

-P

t Page 5

EXERCISE 8: USING USER-DEFINED STRUCTURES AND ARRAYS __________________________________79

OPENING THE CONTROLLER FILE AND EXAMINING THE COOKIE RECIPE _________________________79

EXAMINING THE COOKIE ARRAY AND ADDING YOUR OWN COOKIE RECIPE _______________________80

REVIEWING THE LADDER PROGRAM____________________________________________________81

EXERCISE 9: USING THE ONLINE MANUALS AND HELP FEATURES _________________________________83

ACCESSING THE ONLINE MANUALS ____________________________________________________83

USING ONLINE HELP_______________________________________________________________84

Allen-Bradley Parts

-Q

A-

-E

N-

-P

t Page 6

Notes:__________________________________________________________________________

-Q

A-

-E

N-

-P

t Page 7

Welcome to ControlLogix Controller Quick Start:

About the Exercises

The objective of these exercises is to introduce you to the ControlLogix controller and the RSLogix 5000

programming software. The ControlLogix controller is part of the Logix family of controllers, including the

CompactLogix, FlexLogix, and SoftLogix5800 platforms.

During these exercises, you create and edit a Controller1.ACD file. You will also use the following files:

§ImportExport.ACD

§ReusableCode.ACD

§UserDefined.ACD

§ControlLogixSampleTags.CSV

See http://www.ab.com/logix/controllogix/programfiles for these additional files. They are in a zip file named

control_verA.zip. After you install the RSLogix 5000 software and you download the zip file, unzip the contents

to: C:\RSLogix 5000\Projects. This is the default directory for RSLogix 5000 software project files. You can

save to a different location, just remember the location when you are prompted to open one of the above files.

About the ControlLogix Platform

The ControlLogix platform provides a modular control platform suited for sequential, process, drive, or motion

control - in any combination. With this platform, you can mix multiple processors, networks, and I/O without

restrictions. And as your system grows, you can use the ControlNet network to distribute control to additional

chassis and/or other Logix platforms.

A ControlLogix system can consist of anything from a stand-alone controller and I/O modules in a single

chassis, to a highly distributed system consisting of multiple chassis and networks working together.

ControlLogix will fit your applications if they:

§require a high performance control solution

§demand the integration of multiple control disciplines (e.g., high speed packaging machines integrating

sequential and motion control, or web handling applications integrating sequential and drive control)

§combine batch and process control, but seek a flexible choice of visualization software

§require a plant-wide control solution, from incoming materials to outbound shipping

§expand an existing investment in a PLC-5 or SLC 500 controller-based system

Allen-Bradley Parts

-Q

A-

-E

N-

-P

t Page 8

About the FlexLogix Platform

The FlexLogix platform combines the high performance Logix control engine with the popular distributed FLEX

I/O to provide a cost-effective distributed controller. The FlexLogix system is built on these components:

§a FlexLogix controller which supports Logix instructions

§RSLogix 5000 programming software

§FLEX I/O modules which provide a compact, DIN-rail mounted I/O system

§a 1788 communication daughtercard which provides communication over a standards-based ControlNet

network

A simple FlexLogix system can consist of a single, stand-alone assembly with one controller and as many as

eight I/O modules, or you can use multiple controllers across networks and distribute multiple I/O platforms

over multiple I/O links. FlexLogix will fit your applications if:

§you are already using FLEX I/O and are looking for a simple way to add control to your distributed

architecture

§you are currently using a centralized control architecture to control multiple stations in a process

About the CompactLogix Platform

The features, scalability, and small size of the CompactLogix platform provide a powerful alternative for

machine-level control, material handling, data acquisition, and other applications requiring limited I/O (up to

128 points) and limited communications capability.

CompactLogix will fit your applications if:

§you are an existing Logix customer with lower-end, lower-cost control applications

§you are a new customer who wishes to apply Logix technology, but at a lower initial investment

§you are an existing PLC and/or SLC customer who wishes to convert to Logix technology

§you run SCADA/RTU applications within a range of industries (e.g., petrochemical, wastewater, etc.)

About the SoftLogix Platform

The SoftLogix platform is a PC-based control system that integrates sequential and motion control. The

SoftLogix system is built on these components:

§the Logix control engine

§RSLogix 5000 programming software

§a virtual chassis application which runs on a Pentium-based computer

SoftLogix will fit your applications if:

§you are already using PC-based control

§you have a need for integrated motion capabilities

§you have a need for high-level information integration

§you want to completely customize your application

-Q

A-

-E

N-

-P

t Page 9

Before You Begin

Before you begin these exercises, please be sure to close any applications that are currently running. The

starter kit includes this equipment:

§1756-L55M13 ControlLogix controller (install in slot 0)

§1756-A7 chassis with 7 slots

§1756-PA72 power supply

§1756-CP3 serial cable

§1756IB16 digital input module (install in slot 1)

§1756-IF8 analog input module (install in slot 3)

§1756-OB16E digital output module (install in slot 2)

§1756-OF4 analog output module (install in slot 4)

§1756-TBNH removable terminal block (three blocks for use with the 1756-IB16, 1756-OB16E, and

1756-OF4 modules)

§1756-TBS6H (for use with the 1756-IF8 module)

§9324-RLD300ENE RSLogix 5000 programming software, standard package

§1756-DPALEN ControlLogix controller documentation set

§1756-QS104A-EN-P ControlLogix quick start manual

Document Conventions

Throughout this manual, we have used the following conventions to help guide you through the exercises:

This style or symbol: Indicates:

Words shown in bold italics

(e.g., RSLogix 5000)An item that you must click on or a menu name from which you

must choose an option or command.

Words shown in single

quotes (e.g., 'Controller1') An item that you must type in the specified field.

FYI The text that follows this symbol is additional information

regarding the exercises, but not information that is required

reading in order for you to complete the exercises

Tip The text that follows this symbol provides you with helpful hints

that may make it easier for you to use the software.

The text that follows this symbol is a step in the exercise in

which you are working. Place a checkmark in this box as you

complete each step.

Note, also, that if the mouse button is not specified in the text, you should click on the left mouse button.

Allen-Bradley Parts

-Q

A-

-E

N-

-P

t Page 10

Installing the Hardware

For information on installing the ControlLogix controller, see the ControlLogix Controller Installation

Instructions, publication 1756-IN101. This publication is part of the documentation set, 1756-DPALEN, that is

included with the ControlLogix Starter Kit.

For information on installing the remaining hardware, see:

Hardware Documentation

1756-PA72 1756-IN067

1756-IB16 1756-IN031

1756-IF8 1756-IN040

1756-OB16E 1756-IN030

1756-OF4 1756-IN016

These publications are available as PDF files from the Automation Bookstore at

http://www.theautomationbookstore.com/

Installing the RSLogix 5000 Programming Software

The personal computer must meet these requirements:

§Pentium II 450 MHz (733 MHz recommended)

§128 Mbytes of RAM (256 Mbytes recommended)

§100 Mbytes of available hard disk space

§800 x 600 video resolution (1024 x 768 recommended)

Before you install RSLogix 5000 programming software, you must:

§Make sure RSLinx software is already installed on the personal computer. If it is not, you can install

RSLinx software from the CDs that come with RSLogix 5000 programming software.

§Install firmware onto the ControlLogix controller. The installation instructions for the controller (publication

1756-IN101) describe how to install the firmware. The firmware files are on the second CD that comes with

the RSLogix 5000 software package.

When you insert the RSLogix 5000 installation CD into your CDROM drive, the CD automatically begins the

Setup program for the programming software. If your computer meets the hardware and software requirements

for the controller, you can install the programming software.

Note: These installation instructions are only a summary of the installation procedure. For the complete

procedure, see the RSLogix 5000 Programming Software Getting Results Guide, publication 9399-RLD300GR.

This document is available in PDF format on the RSLogix 5000 CD.

1. Select Install RSLogix 5000.

2. When prompted for a serial number, enter any sequence of characters, not longer than 10 characters in

length. Press F1 if you need help.

3. When prompted, click Yes to complete the activation of the software.

Follow the directions that appear on your screen.

4. Click on Finish to complete the installation.

When the setup utility finishes, an entry for the RSLogix 5000 application program appears in the

program list in the Rockwell Software group.

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley Kinetix 6000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Nederman 4502137 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5 series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Logix5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardLogix 5570 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Mini-PLC-2/15 Einrichtungshandbuch

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Betriebsanleitung

Allen-Bradley

Allen-Bradley PLC-5/12 Einrichtungshandbuch

Allen-Bradley

Allen-Bradley 160 SSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley micrologix 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1305 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro850 series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SMC-50 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 20A Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro820 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-L72EROM Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 20-750-S1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5 series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch