Allen-Bradley ControlLogix System 1756-L1 Bedienungsanleitung

ControlLogix™

System

1756-L1, -L1Mx, -L55Mxx, -L63

User Manual

Allen-Bradley HMIs

Important User Information

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of these

products must satisfy themselves that all necessary steps have been

taken to assure that each application and use meets all performance

and safety requirements, including any applicable laws, regulations,

codes and standards. In no event will Rockwell Automation be

responsible or liable for indirect or consequential damage resulting

from the use or application of these products.

Any illustrations, charts, sample programs, and layout examples

shown in this publication are intended solely for purposes of

example. Since there are many variables and requirements associated

with any particular installation, Rockwell Automation does not assume

responsibility or liability (to include intellectual property liability) for

actual use based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation and Maintenance of Solid-State Control

(available from your local Rockwell Automation office), describes

some important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole

or part, without written permission of Rockwell Automation, is

prohibited.

Throughout this publication, notes may be used to make you aware of

safety considerations. The following annotations and their

accompanying statements help you to identify a potential hazard,

avoid a potential hazard, and recognize the consequences of a

potential hazard:

WARNING

Identifies information about practices or

circumstances that can cause an explosion in a

hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

ATTENTION

Identifies information about practices or

circumstances that can lead to personal injury or

death, property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

1Publication 1756-UM001E-EN-P - August 2002

Summary of Changes

Introduction

This release of this document contains new and updated information.

To find new and updated information, look for change bars, as shown

next to this paragraph.

Updated Information

The document contains the following changes:

Deleted Information

The following information was removed from this manual:

•Estimate Execution Time

•Estimate Memory Use

You can find this information in Logix5000 Controllers Execution Time

and Memory Use Reference Manual, publication 1756-RM087.

This change: Starts on page:

Addition of information on the battery life of the 1756-BA1 battery

when you use it in a ControlLogix5563 controller

25-3

Addition of information a 1756-BATM ControlLogix battery module,

including how to:

•estimate battery life

•replace the battery.

26-1

Allen-Bradley HMIs

Publication 1756-UM001E-EN-P - August 2002

Summary of Changes 2

Notes:

1Publication 1756-UM001E-EN-P - August 2002

Preface

Purpose of this Manual

This manual guides the development of projects for ControlLogix

controllers. It provides step-by-step procedures on how to establish

communications:

•over the following networks

–EtherNet/IP

–ControlNet™

–remote I/O

–DH+™

–DH-485

–serial

•with the following devices

–controllers

–I/O

–workstations

–PanelView™terminals

This manual works together with the Logix5000 Controllers Common

Procedures, publication 1756-PM001, which covers the following

tasks:

•Manage project files

•Organize your logic

•Organize tags

•Program routines

•Test a project

•Handle faults

Who Should Use this

Manual

This manual is intended for those individuals who program

applications that use ControlLogix controllers, such as:

•software engineers

•control engineers

•application engineers

•instrumentation technicians

Allen-Bradley HMIs

Publication 1756-UM001E-EN-P - August 2002

Preface 2

When to Use this Manual

Use this manual:

•when you are ready to integrate your application with the I/0

devices, controllers, and networks in your system.

•after you perform these actions:

–develop the basic code for your application

–perform isolated tests of your application

How to Use this Manual

This manual is divided into the basic tasks that you perform while

programming a ControlLogix controller.

•Each chapter covers a task.

•The tasks are organized in the sequence that you will typically

perform them.

As you use this manual, you will see some terms that are formatted

differently from the rest of the text:

Text that is: Identifies: For example: Means:

Italic the actual name of an item that you

see on your screen or in an example

Right-click User-Defined … Right-click on the item that is named

User-Defined.

courier information that you must supply

based on your application (a

variable)

Right-click

name_of_program …

You must identify the specific program in

your application. Typically, it is a name or

variable that you have defined.

iPublication 1756-UM001E-EN-P - August 2002

Table of Contents

Chapter 1

Configure an EtherNet/IP Module

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 1-1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

RSLogix 5000 Software . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

RSLinx Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

BOOTP Server Software . . . . . . . . . . . . . . . . . . . . . . . . 1-5

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 1-6

Configure a Module Using RSLogix 5000 Software . . . . . . . 1-7

Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Connect to the Module. . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Configure the Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Check the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Configure a Module Using RSLinx Software . . . . . . . . . . . . 1-13

Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Configure the Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Check the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Configure a Module Using BOOTP . . . . . . . . . . . . . . . . . . 1-16

Install BOOTPServer Software . . . . . . . . . . . . . . . . . . . 1-16

Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Enter the Default Network Settings . . . . . . . . . . . . . . . . 1-17

Configure the Module . . . . . . . . . . . . . . . . . . . . . . . . . 1-18

Disable BOOTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

Save the Relation List . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

Renew the IP Address of a 1794-AENx Module. . . . . . . . . . 1-20

Install BOOTPServer Software . . . . . . . . . . . . . . . . . . . 1-20

Set Up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

Enter the New Configuration . . . . . . . . . . . . . . . . . . . . 1-21

Send the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Disable BOOTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Save the Relation List . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23

Test the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24

Connect Directly to a Controller. . . . . . . . . . . . . . . . . . . . . 1-24

Connect a Serial Cable . . . . . . . . . . . . . . . . . . . . . . . . . 1-24

Configure a Serial Driver . . . . . . . . . . . . . . . . . . . . . . . 1-26

Chapter 2

Download and Go Online over an

EtherNet/IP Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 2-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 2-1

Configure an Ethernet Driver. . . . . . . . . . . . . . . . . . . . . . . 2-2

Select a Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Allen-Bradley HMIs

Publication 1756-UM001E-EN-P - August 2002

Table of Contents ii

Chapter 3

Communicate with 1756 I/O over

an EtherNet/IP Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 3-1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 3-2

Add the Local 1756-ENBx or -ENET Module. . . . . . . . . . . . 3-3

Add the Remote 1756-ENBx or -ENET Module . . . . . . . . . . 3-5

Add I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Create Aliases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Chapter 4

Communicate with 1794 I/O Over

EtherNet/IP Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 4-1

Before You Use This Procedure. . . . . . . . . . . . . . . . . . . . . 4-2

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 4-2

Add the local 1756-ENBx or -ENET module . . . . . . . . . . . . 4-3

Add the Remote 1794-AENx Module . . . . . . . . . . . . . . . . . 4-5

Add I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Address I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Chapter 5

Communicate with Another

Controller over an EtherNet/IP

Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 5-1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Select a Communication Method . . . . . . . . . . . . . . . . . . . . 5-2

Produce a Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Add the Local 1756-ENBx or -ENET Module. . . . . . . . . . . . 5-4

Add the Remote 1756-ENBx or -ENET Module . . . . . . . . . . 5-6

Add the Other Controller. . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

Consume a Tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

Does Another Controller Require the Data? . . . . . . . . . . . . 5-13

Add the Local 1756-ENBx or -ENET Module. . . . . . . . . . . . 5-14

Enter a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16

Configure the Message . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

Stagger the Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22

Access ControlLogix Data . . . . . . . . . . . . . . . . . . . . . . . . . 5-23

Publication 1756-UM001E-EN-P - August 2002

Table of Contents iii

Chapter 6

Communicate with a PanelView

™

Terminal Over a EtherNet/IP

Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 6-1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 6-2

Add the Local 1756-ENBx or -ENET Module. . . . . . . . . . . . 6-3

Add the PanelView Terminal . . . . . . . . . . . . . . . . . . . . . . . 6-5

Organize Your Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Configure the PanelView Terminal. . . . . . . . . . . . . . . . . . . 6-10

Create PanelView Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14

Chapter 7

Communicate with an RSView

Project over an EtherNet/IP

Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 7-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 7-1

Configure an Ethernet Driver. . . . . . . . . . . . . . . . . . . . . . . 7-2

Select a Communication Method . . . . . . . . . . . . . . . . . . . . 7-3

Create a Polled Topic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Create a Polled Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

Import Logix5000 Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

Create an .L5K File. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

Install the Logix 5000 Tag Import Utility . . . . . . . . . . . . 7-8

Use the Utility to Create a .CSV File . . . . . . . . . . . . . . . 7-8

Import the .CSV File. . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

Create a Polled Tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

Create a Unsolicited Topic. . . . . . . . . . . . . . . . . . . . . . . . . 7-14

Add the 1756-ENBx or -ENET Module . . . . . . . . . . . . . . . . 7-16

Enter a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18

Configure the Message . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

Create an Unsolicited Node . . . . . . . . . . . . . . . . . . . . . . . . 7-22

Create an Unsolicited Tag . . . . . . . . . . . . . . . . . . . . . . . . . 7-23

Validate an RSView32 Tag . . . . . . . . . . . . . . . . . . . . . . . . . 7-24

Chapter 8

Communicate with 1756 I/O over a

ControlNet™Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 8-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 8-1

Add the Local 1756-CNB Module . . . . . . . . . . . . . . . . . . . . 8-2

Add the Remote 1756-CNB Module . . . . . . . . . . . . . . . . . . 8-4

Add I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Create Aliases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Schedule the ControlNet Network . . . . . . . . . . . . . . . . . . . 8-13

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Allen-Bradley HMIs

Publication 1756-UM001E-EN-P - August 2002

Table of Contents iv

Chapter 9

Communicate with 1771 I/O Over a

ControlNet

™

Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 9-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 9-1

Add the Local 1756-CNB Module . . . . . . . . . . . . . . . . . . . . 9-3

Add the 1771-ACN Module . . . . . . . . . . . . . . . . . . . . . . . . 9-5

Read or Write Data To or From a Block Transfer Module . . 9-7

Read Data From a Block Transfer Module. . . . . . . . . . . 9-8

Write Configuration or Output Data To a Block Transfer

Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

Configure the Messages . . . . . . . . . . . . . . . . . . . . . . . . 9-11

Read or Write Data To or From Multiple Block Transfer Modules

9-12

Create a User-Defined Data Type . . . . . . . . . . . . . . . . . 9-13

Create the Array for the Input Data. . . . . . . . . . . . . . . . 9-14

Send a Block Transfer Read Message . . . . . . . . . . . . . . 9-15

Enter the BTR Properties for Each Module . . . . . . . . . . 9-17

Convert the INTs to DINTs. . . . . . . . . . . . . . . . . . . . . . 9-18

Step to the Next BT Module . . . . . . . . . . . . . . . . . . . . . 9-19

Write Data to Multiple Block Transfer Modules . . . . . . . 9-20

Address I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22

Schedule the ControlNet Network . . . . . . . . . . . . . . . . . . . 9-24

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25

Stagger the Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-27

Chapter 10

Communicate with 1794 I/O Over a

ControlNet

™

Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 10-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 10-1

Add the local 1756-CNB module . . . . . . . . . . . . . . . . . . . . 10-2

Add the Remote 1794-ACN Module . . . . . . . . . . . . . . . . . . 10-4

Add I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6

Create Aliases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10

Schedule the ControlNet Network . . . . . . . . . . . . . . . . . . 10-13

Validate Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14

Chapter 11

Communicate with Another

Controller over a ControlNet

™

Network

When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 11-1

How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 11-2

Step 1: Add the 1756-CNB Module. . . . . . . . . . . . . . . . . . . 11-3

Step 2: Add the Remote 1756-CNB Module. . . . . . . . . . . . . 11-5

Step 3: Add the 1788-CNC Module. . . . . . . . . . . . . . . . . . . 11-8

Step 4: Add the Other Controller . . . . . . . . . . . . . . . . . . . 11-10

Step 5: Enter a Message. . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

Step 6: Configure the Message . . . . . . . . . . . . . . . . . . . . . 11-14

Step 7: Stagger the Messages . . . . . . . . . . . . . . . . . . . . . . 11-16

Step 8: Access ControlLogix Data. . . . . . . . . . . . . . . . . . . 11-16

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley Logix5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactLogix 5480 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1785-L11B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-3 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley controllogix 1756-L61 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 5570 series Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactLogix 5370 L1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 IP00 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40P Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 753 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 198E-C2S4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactLogix Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755TL Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact GuardLogix 5370 Bedienungsanleitung

Allen-Bradley

Allen-Bradley micrologix 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 20F Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch