Allen-Bradley Micro800 Bedienungsanleitung

Installation Instructions

Original Instructions

Micro800 Programmable Controller

External AC Power Supply

Catalog Numbers

2080-PSAC-12W

Topic Page

Important User Information 2

Overview 7

Connect the Power Supply 8

Wire the Module 9

Specifications 10

2Rockwell Automation Publication 2080-IN011B-EN-P - August 2016

Micro800 Programmable Controller External AC Power Supply

Important User Information

Read this document and the documents listed in the additional resources section

about installation, configuration, and operation of this equipment before you

install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to

requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly,

disassembly, and maintenance are required to be carried out by suitably trained

personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect

or consequential damages resulting from the use or application of this

equipment.

The examples and diagrams in this manual are included solely for illustrative

purposes. Because of the many variables and requirements associated with any

particular installation, Rockwell Automation, Inc. cannot assume responsibility

or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use

of information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without

written permission of Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of

safety considerations.

Rockwell Automation Publication 2080-IN011B-EN-P - August 2016 3

Micro800 Programmable Controller External AC Power Supply

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can

cause an explosion in a hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can

lead to personal injury or death, property damage, or economic loss. Attentions

help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding

of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive

or motor, to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive

or motor, to alert people that surfaces may reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a

motor control center, to alert people to potential Arc Flash. Arc Flash will cause

severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow

ALL Regulatory requirements for safe work practices and for Personal Protective

Equipment (PPE).

4Rockwell Automation Publication 2080-IN011B-EN-P - August 2016

Micro800 Programmable Controller External AC Power Supply

Environment and Enclosure

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC 60664-1),

at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR 11. Without appropriate precautions, there may be difficulties with

electromagnetic compatibility in residential and other environments due to

conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental conditions

that will be present and appropriately designed to prevent personal injury

resulting from accessibility to live parts. The enclosure must have suitable flame-

retardant properties to prevent or minimize the spread of flame, complying with a

flame spread rating of 5VA or be approved for the application if nonmetallic. The

interior of the enclosure must be accessible only by the use of a tool. Subsequent

sections of this publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain product safety

certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for additional installation requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the

degrees of protection provided by different types of enclosure.

Rockwell Automation Publication 2080-IN011B-EN-P - August 2016 5

Micro800 Programmable Controller External AC Power Supply

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous locations.

Informations sur l’utilisation de cet équipement en

environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable

for use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations andnonhazardous locations only. Each product

is supplied with markings on the rating nameplate

indicating the hazardous location temperature code.

When combining products within a system, the most

adverse temperature code (lowest "T" number) may be

used to help determine the overall temperature code of

the system. Combinations of equipment in your system

are subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de Classe

I Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque

d'identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de température le plus

défavorable (code de température le plus faible) peut être

utilisé pour déterminer le code de température global du

système. Les combinaisons d'équipements dans le système

sont sujettes à inspection par les autorités locales qualifiées

au moment de l'installation.

WARNING:

Explosion Hazard –

• Do not disconnect equipment

unless power has been removed

or the area is known to be

nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external connections

that mate to this equipment by

using screws, sliding latches,

threaded connectors, or other

means provided with this

product.

• Substitution of components may

impair suitability for Class I,

Division 2.

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

AVERTISSEMENT:

Risque d’Explosion –

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher

l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les connecteurs

externes reliés à cet équipement à

l'aide de vis, loquets coulissants,

connecteurs filetés ou autres moyens

fournis avec ce produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de Classe

I, Division 2.

• S'assurer que l'environnement est

classénon dangereux avantdechanger

les piles.

WARNING:

• When used in a Class I, Division 2, hazardous location, this equipment must be

mounted in a suitable enclosure with proper wiring method that complies

with the governing electrical codes.

• Any fluctuation in voltage source must be within 88…264V AC. Do not

connect the adapter to a power source that has fluctuations outside of this

range.

6Rockwell Automation Publication 2080-IN011B-EN-P - August 2016

Micro800 Programmable Controller External AC Power Supply

ATTENTION:

• Be careful when stripping wires. Wire fragments that fall into the controller

could cause damage. Once wiring is complete, be sure the module is free of all

metal fragments before removing the protective debris strip. Failure to remove

the strip before operating can cause overheating.

• Be careful of metal chips when drilling mounting holes for your controller or

other equipment withinthe enclosure or panel. Drilled fragments that fall into

the controller could cause damage. Do not drill holes above a mounted

controller if the protective debris strips have been removed.

• Electrostatic discharge can damage semiconductor devices inside the adapter.

Do not touch the connector pins or other sensitive areas.

• Mount the power supply vertically.

Allow 50 mm (2 in.) of space on all but the right side for adequate ventilation.

• Do not wire more than 2 conductors on any single terminal.

WARNING: Risk of electrical shock, fire, personal injury or death.

• Do not use the power supply without proper grounding (Protective Earth).

• Turn power off before working on the device.

Protect against inadvertent re-powering.

• Make sure that the wiring is correct by following all local and national codes.

• Do not modify or repair the unit.

• Do not open the unit as high voltages are present inside.

• Use caution to prevent any foreign objects from entering into the housing.

Rockwell Automation Publication 2080-IN011B-EN-P - August 2016 7

Micro800 Programmable Controller External AC Power Supply

Overview

The 2080-PSAC-12W power supply can be used by controllers from the

Micro800® family as an optional AC power source.

8Rockwell Automation Publication 2080-IN011B-EN-P - August 2016

Micro800 Programmable Controller External AC Power Supply

Connect the Power Supply

General Considerations

Most applications require installation in an industrial enclosure to reduce the

effects of electrical interference and environmental exposure. Locate your

module as far as possible from power lines, load lines, and other sources of

electrical noise such as hard-contact switches, relays, and AC motor drives. For

more information on proper grounding guidelines, see the Industrial

Automation Wiring and Grounding Guidelines, publication 1770-4.1.

Module Spacing

Maintain spacing from objects such as enclosure walls, wireways and adjacent

equipment. Allow 50.8 mm (2 in.) of space on all sides for adequate ventilation.

An exception to this spacing guideline is allowed for the side at which you are

connecting a Micro800 controller.

7.2

110.7 100 90

7.2

Measurements in millimeters

Rockwell Automation Publication 2080-IN011B-EN-P - August 2016 9

Micro800 Programmable Controller External AC Power Supply

DIN Rail Mounting

Use a flat-blade screwdriver to mount the power supply on EN50022-35x7.5

DIN rails.

Panel Mounting

The preferred mounting method is to use four M4 (#8) screws per module. Hole

spacing tolerance: ±0.4 mm (0.016 in.).

Follow these steps to install the power supply using mounting screws.

1. Place the power supply against the panel where you are mounting it.

Make sure the power supply is spaced properly.

2. Mark drilling holes through the mounting screw holes and mounting

feet then remove the power supply.

3. Drill the holes at the markings, then replace the power supply and

mount it.

Wire the Module

PAC-1

PAC-2

PAC-3

DC-1

DC-2

Power LED Finger guard

(transparent cover)

10 Rockwell Automation Publication 2080-IN011B-EN-P - August 2016

Micro800 Programmable Controller External AC Power Supply

Specifications

AC Input Connectors DC Output Connectors (DC 24V / 0.5 A)

PAC-1 AC hot 100...240V AC DC-1 -

PAC-2 AC neutral 100...240V AC DC-2 +

PAC-3 Safety ground

ATTENTION: Replace the finger guard after wiring the power supply.

General

Attribute Value

Dimensions, HxWxD 90 x 39 x 75 mm (3.54 x 1.54 x 2.95 in)

Shipping weight 0.2 kg (0.44 lb)

Supply voltage range(1) 100V…120V AC, 0.7 A

200…240V AC, 0.4 A

Supply frequency 47…63 Hz

Supply power 24V DC, 0.9 A @ 50 °C

24V DC, 0.5 A @ 65 °C

Inrush current, max 25 A @ 132V for 10 ms

40 A @ 265V for 10 ms

Line loss ride through 10...3000 ms @ 88V AC

Power consumption

(Output power) 21.6W @ 50 °C

12W @ 65 °C

Power dissipation

(Input power) 27W (115V AC), 26.7W (230V AC) @ 50 °C

15.4W (115V AC), 15.2W (230V AC) @ 65 °C

Isolation voltage 250V (continuous), Primary to Secondary: Reinforced Insulation Type

Type tested for 60s at 2300V AC primary to secondary and 1350V AC primary to

earth ground.

Andere Handbücher für Micro800

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley SLC 500 1747-L20 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-L61S ControlLogix 5561S Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactLogix 1769-L23E-QB1B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 400 Gebrauchsanweisung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SMC-50 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SMC-3 150-CF147 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1100 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755TL Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 20A Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1000 PLC Leitfaden

Allen-Bradley

Allen-Bradley GuardPLC 1754 Bedienungsanleitung

Allen-Bradley

Allen-Bradley controllogix 1756-L61 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SMC-50 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-OC Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 GuardLogix Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch