Allen-Bradley VPL-SSN Bedienungsanleitung

Installation Instructions

Original Instructions

Shaft Seal Kits

Catalog Numbers

VPL-SSN, VPL-SS, VPC-SSN, VPF-SSN, VPH-SST, MPL-SSN, MPF-SST, MPS-SST, TL-SSN

Summary of Changes

This publication contains new and updated information as indicated in the following table.

Topic Page

Summary of Changes 1

About Shaft Seals 2

Required Tools 2

Remove the Shaft Seal 3

Replace the Shaft Seal 4

Shaft Seal Kit Catalog Numbers 6

Additional Resources 8

Topic Page

Updated the shaft seal remove and replace procedures. 3, 4

Added Kinetix® VP hygienic servo motors to the Shaft Seal Installation Clearances figure and table. 5

Added Kinetix VP hygienic servo motors to the Shaft Seal Kit Catalog Numbers table. 7

2Rockwell Automation Publication 2090-IN012E-EN-P - February 2019

Shaft Seal Kits

About Shaft Seals

A shaft seal is recommended if the motor shaft and end bell are exposed to significant amounts of

containments, such as oil, fluids, or fine dust. Use a shaft seal in these environments to prolong

the life of the motor. A shaft seal and Bulletin 2090 cables with environmentally sealed

connectors are required for an IP66 rating or greater.

See Kinetix Motion Accessories Specifications Technical Data, publication KNX-TD004, to

find Bulletin 2090 cables with environmentally sealed connectors for your motor.

Required Tools

Use these tools to install a shaft seal:

• Appropriately sized screw or bolt to grip and remove the worn shaft seal

• Rubber/wooden mallet or a metal hammer and wooden work piece

• Socket, pipe, or tubing (various sizes)

• Abrasive cloth to remove any nicks or burrs from the motor shaft

IMPORTANT The shaft seal is not required in applications where the motor shaft and end bell are free of oil,

fluids, or fine dust, and a lower IP rating is sufficient.

Shaft seals are subject to wear and require periodic inspection and replacement. Replacement

is recommended every 3 months, not to exceed 12 months, depending on use.

If you paint the motor, do not get paint on the shaft seal area or the shaft, as this can decrease

the life of the shaft seal.

Oil, Fluids, and Fine Dust Oil, Fluids, and Fine Dust

Shaft Seal Installation

is Recommended

Shaft Seal Installation

is Not Recommended

Motor Shaft and

End Bell are Exposed

to Containments

Motor Shaft and

End Bell are Protected

From Containments

Oil, Fluids, and Fine Dust

Shaft Seal Installation

is Not Recommended

Rockwell Automation Publication 2090-IN012E-EN-P - February 2019 3

Shaft Seal Kits

Remove the Shaft Seal

The shaft seal can be safely removed by partially inserting an appropriately sized screw or bolt

into the face of the shaft seal. The head of the screw or bolt provides a convenient point to grasp

and remove the shaft seal.

Before installing the screw, create a pilot hole appropriate for the screw being used. Use masking

tape or a depth sleeve to establish a drilling depth limit of 4 mm (0.16 in.) from the tip of the drill

bit.

Follow these steps to remove the shaft seal.

1. Remove power to the motor before removing the shaft seal.

2. Drill a pilot hole in the face of the shaft seal less than the depth limit specified above.

Make sure the drill does not come in contact with the shaft seal bore.

3. Thread your screw or bolt into the pilot hole.

4. Lift the shaft seal from the motor by grasping the screw head and slightly rotating the

seal while pulling.

5. Inspect and clean the shaft and sealing surfaces as necessary.

Use an abrasive cloth to remove any nicks or burrs from the motor shaft.

ATTENTION: To avoid injury or damage to the equipment, remove power from the motor before

removing the shaft seal.

ATTENTION: Do not drill into the shaft seal deeper than 4 mm (0.16 in.).

Drilling and inserting a screw completely through the shaft seal can damage the motor bearings,

and require factory service to repair the motor.

IMPORTANT Cover the sharp edges of the keyway with tape to protect the shaft seal lip from

damage.

4Rockwell Automation Publication 2090-IN012E-EN-P - February 2019

Shaft Seal Kits

Replace the Shaft Seal

Follow these steps to replace the shaft seal.

1. Apply tape to the keyway opening so the edges do not damage the seal lip.

2. Lubricate the motor shaft and the inner lip of the shaft seal with lubricant that is

supplied in the kit.

3. Center the shaft seal on the mounting surface of the motor and slide the shaft seal evenly

onto the motor shaft.

See Shaft Seal Installation Clearances on page 5 for the correct installation clearance of

the shaft seal you are installing.

4. Press the shaft seal into the seal bore by applying one of the Shaft Seal Installation

Methods on page 6.

5. Visually inspect for irregularities in the shaft seal or an uneven alignment where the shaft

seal contacts the motor.

Verify that the outer and inner circumference of the shaft seal is fully seated into

position.

6. Verify that the shaft seal is installed to the correct installation clearance.

• If the shaft seal is installed too deep, it can become subject to excessive wear and

require frequent replacement.

• If the shaft seal is installed too shallow, it can reduce the effectiveness of the

protective seal.

IMPORTANT Shaft seals require a lubricant to reduce wear. The lubricant is supplied with the

shaft seal kits. Lubricate only the inner lip of the shaft seal. Do not lubricate the

motor bore or outside diameter of the seal.

VPH-SST-Fxxx Shaft Seal

Back View of Shaft Seal

(motor facing)

Inside of Shaft Seal Lip

VPS-SST-xxxx Shaft Seal

MPS-SST-xxxx Shaft Seal

Rockwell Automation Publication 2090-IN012E-EN-P - February 2019 5

Shaft Seal Kits

Shaft Seal Installation Clearances

Motor Cat. No.

Shaft Seal Installation Clearance

Min, mm (in.) Nom, mm (in.) Max, mm (in.)

VPL-Axxx and VPL-Bxxx

Press the shaft seal so that the seal is flush or below the front surface of the motor.

VPC-Bxxx

VPF-Axxx and VPF-Bxxx

1.40 (0.055) 1.50 (0.060) 1.65 (0.065)

VPS-Bxxx

VPH-Axxx and VPH-Bxxx Press the shaft seal so that the seal is flush with the front surface of the motor.

MPL-A15xx and MPL-B15xx

1.50 (0.060) 2.00 (0.080) 3.00 (0.120)

MPL-A2xx and MPL-B2xx

All other MPL-A/Bxxx

Press the shaft seal so that the seal is flush or below the front surface of the motor.

MPM-Axxx and MPM-Bxxx

MPF-Axxx and MPF-Bxxx

1.40 (0.055) 1.50 (0.060) 1.65 (0.065)

MPS-Axxx and MPS-Bxxx

MDF-SBxxx 1.40 (0.055) 1.50 (0.060) 1.65 (0.065)

TL-Series Press the shaft seal so that the seal is flush or below the front surface of the motor.

Front Surface

of Motor

Shaft Seal Pressed

Flush with Front

Surface of Motor

Shaft Seal Pressed

Below Front

Surface of Motor

Front Surface

of Motor

Nom

Min

Max

Front Surface

of Motor

Shaft Seal

Shaft Seal on

Motor Shaft

Shaft Seal Pressed

Flush with Front

Surface of Motor

Shaft Seal on

Motor Shaft

Bulletin VPH

Shaft Seal

Example

Bulletin VPL, Other MPL,

MPM, and TL-Series

Shaft Seal Example

Bulletin VPS, VPF, MPL-A/B15xx,

MPL-A/B2xx, MPF, MPS, and

MDF Shaft Seal Example

6Rockwell Automation Publication 2090-IN012E-EN-P - February 2019

Shaft Seal Kits

Shaft Seal Installation Methods

Shaft Seal Kit Catalog Numbers

ATTENTION: Do not hammer directly on the shaft seal. Gently tap the socket, pipe, or tubing

evenly around the outer edge of the shaft seal until the shaft seal is pressed into place. Make sure

the socket, pipe, or tubing you use does not contact the shaft seal lip. Permanent damage to the

shaft seal can occur.

IMPORTANT Third-party shaft seals are not approved for use with these motors. The use of third-party shaft

seals voids any implied or expressed warranties.

Kinetix VP Low Inertia Motors Kinetix VP Food Grade Motors

Motor Cat. No. Shaft Seal Kit Cat. No. Motor Cat. No. Shaft Seal Kit Cat. No.

VPL-A063xx and VPL-B063xx

VPL-SSN-F063075

VPF-A063xx and VPF-B063xx

VPF-SSN-F063075

VPL-A075xx and VPL-B075xx VPF-A075xx and VPF-B075xx

VPL-A100xx and VPL-B100xx MPL-SSN-A3B3 VPF-A100xx and VPF-B100xx MPF-SST-A3B3

VPL-A115xx and VPL-B115xx MPL-SSN-A4B4 VPF-A115xx and VPF-B115xx MPF-SST-A4B4

VPL-A130xx and VPL-B130xx MPL-SSN-A5B5 VPF-A130xx and VPF-B130xx MPF-SST-A45B45

VPL-B165xx MPL-SSN-F165 VPF-B165xx MPF-SST-F165

Kinetix VP Continuous Duty Motors Kinetix VP Stainless Steel Motors

Motor Cat. No. Shaft Seal Kit Cat. No. Motor Cat. No. Shaft Seal Kit Cat. No.

VPC-B165xx MPL-SSN-A6B6 VPS-B1304D MPS-SST-A45B45

VPC-B215xx VPL-SS-X256 VPS-B1653D MPS-SST-F165

VPC-B300xx VPC-SSN-F300

Socket, Pipe, or Tubing

(supplied by the customer)

Motor

Metal

Hammer

Shaft Seal

Wooden

Work

Piece

Rubber or

Wooden Mallet

Motor

Shaft Seal

Socket, Pipe, or Tubing

(supplied by the customer)

Rockwell Automation Publication 2090-IN012E-EN-P - February 2019 7

Shaft Seal Kits

Kinetix VP Hygienic Servo Motors MP-Series Stainless Steel Motors

Motor Cat. No. Shaft Seal Kit Cat. No. Motor Cat. No. Shaft Seal Kit Cat. No.

VPH-A063xx and VPH-B063xx VPH-SST-F063 MPS-A3xx and MPS-B3xx MPS-SST-A3B3

VPH-A075xx and VPH-B075xx VPH-SST-F075 MPS-A45xx and MPS-B45xx MPS-SST-A45B45

VPH-A100xx and VPH-B100xx VPH-SST-F100 MPS-B5xx MPS-SST-F165

VPH-A115xx and VPH-B115xx VPH-SST-F115 MP-Series Medium Inertia Motors

VPH-A130xx and VPH-B130xx VPH-SST-F130 Motor Cat. No. Shaft Seal Kit Cat. No.

VPH-B165xx VPH-SST-F165 MPM-A115x, MPM-B115xx MPL-SSN-A4B4

MP-Series Low Inertia Motors MPM-A130xx, MPM-B130xx MPL-SSN-A5B5

Motor Cat. No. Shaft Seal Kit Cat. No. MPM-A165xx, MPM-B165xx MPL-SSN-F165

MPL-A15xx and MPL-B15xx

MPL-SSN-F63F75

MPM-A215xx, MPM-A215xx MPL-SSN-A6B6

MPL-A2xx and MPL-B2xx Kinetix 6000M Integrated Drive-Motor

MPL-A3xx and MPL-B3xx MPL-SSN-A3B3 Motor Cat. No. Shaft Seal Kit Cat. No.

MPL-A4xx and MPL-B4xx MPL-SSN-A4B4 MDF-SB1003 MPF-SST-A3B3

MPL-A45xx and MPL-B45xx MPL-SSN-A5B5 MDF-SB1153 MPF-SST-A4B4

MPL-A520 and MPL-B520

MPL-A540 and MPL-B540

MPL-A560 and MPL-B560

MPL-SSN-F165 MDF-SB1304 MPF-SST-A45B45

MPL-B580 MPL-SSN-F165-32MM TL-Series Low Inertia Motors

MPL-B6xx MPL-SSN-A6B6 Motor Cat. No. Shaft Seal Kit Cat. No.

MPL-B8xx MPL-SSN-A8B8 TLY-A1xx and TL-A1xx TL-SSN-1

MPL-B9xx MPL-SSN-A9B9 TLY-A2xx and TL-A2xx TL-SSN-2

MP-Series Food Grade Motors TLY-A25xx and TL-A25xx

TL-SSN-3

Motor Cat. No. Shaft Seal Kit Cat. No. TLY-A3xx

MPF-A3xx and MPF-B3xx MPF-SST-A3B3 TL-A4xx TL-SSN-4

MPF-A4xx and MPF-B4xx MPF-SST-A4B4

MPF-A45xx and MPF-B45xx MPF-SST-A45B45

MPF-A5xx and MPF-B5xx MPF-SST-F165

Allen-Bradley, Kinetix, MP-Series, Rockwell Automation, Rockwell Software, and TL-Series are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication 2090-IN012E-EN-P - February 2019

*PN-522270*

PN-522270

Additional Resources

These documents contain additional information concerning related products from Rockwell

Automation.

You can view or download publications at http://www.rockwellautomation.com/global/

literature-library/overview.page.

Resource Description

Kinetix Rotary Motion Specifications Technical Data,

publication KNX-TD001

Product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPS),

MP-Series™ (Bulletin MPL, MPM, MPF, MPS), Kinetix 6000M (Bulletin

MDF), and TL-Series™ rotary motors.

Kinetix Motion Accessories Specifications Technical

Data, publication KNX-TD004

Product specifications for Bulletin 2090 motor and interface cables, low-

profile connector kits, drive power components, and other servo drive

accessory items.

Kinetix Motion Control Selection Guide,

publication KNX-SG001

Overview of Kinetix servo drives, motors, actuators, and motion

accessories designed to help make initial decisions for the motion

control products best suited for your system requirements.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1

Provides general guidelines for installing a Rockwell Automation

industrial system.

Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other certification

details.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Industrieelektrik Handbücher

Allen-Bradley

Allen-Bradley Prosafe 440T-MSTUEx Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX 5000 5094-IY8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G2-K Bedienungsanleitung

Allen-Bradley

Allen-Bradley 194U-S1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley 100-D210 El Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140M-C-AFC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 REGEN Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-R Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-R-EP Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-R Series Bedienungsanleitung

Beliebte Industrieelektrik Handbücher anderer Marken

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch

Abtech

Abtech HVJB Series Leitfaden

Murata

Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Bedienungsanleitung

Eaton

Eaton Ulusoy HMH24-04 Bedienungsanleitung

Murata

Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung

Newlong

Newlong NP-7H Bedienungsanleitung

Stahl

Stahl 8575/12 Bedienungsanleitung

SI Pegasus Bedienungsanleitung

Murata

Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung

Murata

Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung

Cooper Power Systems

Cooper Power Systems VXE15 Bedienungsanleitung

S&C

S&C Vista SD Bedienungsanleitung

Murata

Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung

Siemens

Siemens 3VA9988-0BM10 Bedienungsanleitung

Siemens

Siemens SITRANS LVS100 Bedienungsanleitung

Murata

Murata GRM32ER60G227ME05 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung