SI Pegasus Bedienungsanleitung
Pegasus
Installation Instructions
400243 |v. 1.0 |29 August 2023
DATA
Pegasus
302304
V+
V-
+
G
-
COMPAT LOCAL
CHANNEL
FCC ID: 2ASYG-PEGASUS1
R.RX
R.TX
PROG
RF
LEARN
Please use this QR Code to access more
documents and Video Tutorials related to the
product.
FCC INFORMATION
This device complies with FCC RF radiation exposure limits set forth for general population.
This device must be installed to provide a separation distance of at least 20cm from all persons
and must not be co-located in conjunction with any other antenna or transmitter. This device
complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. NOTE: This
equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the the interference by one or more of the following measures:- - - -
Reorient or relocate the receiving antenna. - Increase the separation between the equipment
and receiver. - Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
This device complies with Canada's license-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Scan the QR code to scan Pegasus specsheet
Tech Specs
Technical Support: 512.832.6939
Hours of Support: 7:30am - 5pm CST
CONTENTS
Parts in the Box 4
Mounting Options 5
RJ45 and Power Pinouts 6
GPI/O and Dry Contact Pinouts 7
IR HEX codes 8
LED Details 9
User Button Actions 10
Learning Somfy/Olibra Remotes, Keypads & Sensors 11
Learning Pico Remotes to Control a 485 Motor 12
Programming an RTS Motor Channel 13
RTS Smart Repeater Setup 14
RTS to 485 Smart Receiver Setup 15
485 to RTS Smart Transmitter Setup 16
Network Mode 17
Factory Reset 18
4
PARTS IN THE BOX
(1) White Decora
Wall Trim Plate
(1) Pegasus (1) Pegasus
Decora Label
(1) AUX USB
Power Cable
(1) CAT5e (2) J Box
screws
(2)Trim plate
screws
5
Left or Right Din Rail
mounting
Standard single or
multiple gang J Box
MOUNTING OPTIONS
Choose your mounting:
Pegasus Pro-tip
It is best not to mount Pegasus in a metal J Box
6
RJ45 AND POWER PINOUTS
5 position removable screw-down Terminal
block connector for GPI/O
Aux power Input (7-28vDC)
Data +(WHT/ ORG)
Data - (ORG)
N/A (WHT/ GRN)
N/A (GRN)
Power + (BLUE)
Ground - (WHT/ BRWN)
Ground - (BRWN)
Power + (WHT/ BLUE)
485 Connection (TIA 568B) RJ Pin Outs
1
8
DATA
Pegasus
302304
V+
V-
+
G
-
COMPAT LOCAL
CHANNEL
FCC ID: 2ASYG-PEGASUS1
R.RX
R.TX
PROG
RF
LEARN
- Ground (USB Black)
+7-28vDC Positive (USB Red)
7
GPI/O AND DRY CONTACT PINOUTS
UP
STOP
12 V Trigger
Sleeve
Tip DC
0 - 10V Input
GND (PINK) (-)
POSITIVE (VIOLET) (+)
IR Input
BLACK (IR/SERIAL-)(GND)
YELLOW (IR/SERIAL+)(485 DATA -(SIG OUT))
GREEN(DATA +(VSI)
Dry Contacts
DOWN
8
IR HEX CODES
0000 006c 0000 000c 0006 011b 0006
011b 0006 00bb 0006 00bb 0006 00bb
0006 00bb 0006 00bb 0006 00bb 0006
00bb 0006 00bb 0006 011b 0006 08a4
0000 006c 0000 000c 0006 011b 0006
011b 0006 00bb 0006 00bb 0006 00bb
0006 00bb 0006 00bb 0006 00bb 0006
00bb 0006 011b 0006 011b 0006 08a4
0000 006c 0000 000c 0006 011b 0006
011b 0006 00bb 0006 00bb 0006 00bb
0006 00bb 0006 00bb 0006 00bb 0006
00bb 0006 011b 0006 00bb 0006 08a4
UP
STOP
DOWN
Third party IR universal control systems may be used to control
the screen or using these hex codes: (Available on the website too.)
* Not included / optional
9
LED DETAILS
Compatible Mode
ON when in Compatible
Mode
UP GPI/O
Briefly turns on with a valid up
signal on the GPI/O Connector
Repeater Mode Transmit (Tx)
On SOLID when IN Repeater
RX Mode
Repeater Mode Receive (Rx)
On SOLID when IN Repeater
RX Mode
Sub GHz Signal
Briefly turns on with any valid
Sub GHz Data (Receiving or
Trasmitting)
Both Rx and Tx LED's
remain on when in Rx/Tx
repeater mode
Learn
Flashes when learning a
remote
485 Data/Power
ON, when power from
BUS or AUX is applied
and flashes OFF with
485 data on Bus
DOWN GPI/O
Briefly turns on with
a valid signal on the
GPIO/O Connector
Local Mode
ON when in Local Mode
R.RX
R.TX
DATA
Pegasus
302304
V+
V-
+
G
-
COMPAT LOCAL
CHANNEL
FCC ID: 2ASYG-PEGASUS1
R.RX
R.TX
PROG
RF
LEARN
10
DATA
Pegasus
302304
V+
V-
+
G
-
COMPAT LOCAL
CHANNEL
FCC ID: 2ASYG-PEGASUS1
R.RX
R.TX
PROG
RF
LEARN
USER BUTTON ACTIONS
16 Rx/16 Tx Channels O-F
Note: moving the Hex to C.E.F.
will change the transceiver to
one of three repeater functions
in local mode
HEX Switch Fixed Channels
C = Repeater Transmit Mode (Tx)
R.TX LED ON (Transmits relayed 485
repeater groups)
D = Repeater Receive Mode (Rx)
R.Rx LED ON (relays received RF cmds
and sends over 485)
E = Repeater Legacy Mode (Rx/Tx) Both
R.Rx and R.Tx LED ON (repeats cmds
from Rx. to Tx)
F = Motor Channel / GPI/O Output
Default
Program Button
Press and release sends pairing
command. Use this button to
program SubGHz Motors.
Hold button (3 seconds to reboot and
boot in compatibility mode (Compat
LED turns on)(Legacy mode is
default)toggle
Holding both Program and Learn
button down for approx. 3 secs will
factory reset, all LED's will come on
(erases all channels in and out and
puts Pegasus back in Local mode and
Legacy compatibility)
Learn Button
Press this button (LED starts
flashing) to LEARN a Sub GHz
keypad, remote or sensor on
the currently set Hex CH (up
to 16)
Hold button (3 seconds)
(until LED comes on to erase
the current Hex set remote
channel)
Hexadecimal Switch
Inhaltsverzeichnis
Andere SI Industrieelektrik Handbücher
Beliebte Industrieelektrik Handbücher anderer Marken
Rexroth Indramat
Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch
Abtech
Abtech HVJB Series Leitfaden
Murata
Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung
SAF-HOLLAND
SAF-HOLLAND CBX 5415.5 Bedienungsanleitung
Eaton
Eaton Ulusoy HMH24-04 Bedienungsanleitung
Newlong
Newlong NP-7H Bedienungsanleitung
Murata
Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung
Stahl
Stahl 8575/12 Bedienungsanleitung
Murata
Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung
Murata
Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung
Cooper Power Systems
Cooper Power Systems VXE15 Bedienungsanleitung
S&C
S&C Vista SD Bedienungsanleitung
Murata
Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung
Siemens
Siemens 3VA9988-0BM10 Bedienungsanleitung
Siemens
Siemens SITRANS LVS100 Bedienungsanleitung
Murata
Murata GRM32ER60G227ME05 Series Bedienungsanleitung
Siemens
Siemens SENTRON SUPERSWITCH 3KL82 Series Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung