Allen-Bradley PanelView Plus 7 Bedienungsanleitung

Installation Instructions

PanelView Plus 7 Standard Terminals

Mounting Levers

Catalog Number

2711P-RMCS

Prepare for Panel Mounting

Mounting levers insert into the slots around the bezel to secure the terminal in the panel. The

number of mounting levers varies by terminal size. Each slot has six notches with alignment

marks that are locking positions for a mounting lever. The thickness of the panel in which you

mount the terminal determines the locking position that is required to maintain NEMA, UL

Type, and IP seals.

Mounting Lever Lock Position

ATTENTION:

•Disconnect all electrical power from the panel before making the panel cutout.

•Make sure the area around the panel cutout is clear and that the panel is clean of any debris,

oil, or other chemicals.

•Make sure that metal cuttings do not enter any components that are already installed in the

panel and that the edges of the cutout have no burrs or sharp edges.

•Failure to follow these warnings can result in personal injury or damage to panel components.

IMPORTANT

See the PanelView™ Plus 7 Standard Terminals User Manual, publication 2711P-UM007, for

complete installation instructions.

Mounting Slot Mounting Lever

Lock Position

Panel Thickness Range Typical

Gauge

1 1.50…2.01 mm (0.060…0.079 in.) 16

2 2.03…2.64 mm (0.080…0.104 in.) 14

3 2.67…3.15 mm (0.105…0.124 in.) 12

4 3.17…3.66 mm (0.125…0.144 in.) 10

5 3.68…4.16 mm (0.145…0.164 in.) 8/9

6 4.19…4.80 mm (0.165…0.188 in.) 7

123456

2PanelView Plus 7 Standard Terminals Mounting Levers

Rockwell Automation Publication 2711P-IN032A-EN-P - July 2014

Mounting Lever Orientation and Lock Sequence

Mount the Terminal in a Panel

Follow these steps to mount the terminal in a panel cutout.

1. Use the cutout template that is shipped with your terminal to mark the cutout

dimensions and cut the hole in the panel.

2. Verify the sealing gasket is present on the terminal.

This gasket forms a compression type seal. Do not use sealing compounds.

3. Center the terminal in the panel cutout.

IMPORTANT

The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and

IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in a different

orientation than shown.

942

10 13

10.4- and 12.1-in.

9-in.

6.5-in.

4.3 in. 3

5.7 in.

6482

7153

15-in.

The box indicates that the mounting levers must be

rotated in the orientation that is shown to avoid

interference with ports and cables.

PanelView Plus 7 Standard Terminals Mounting Levers 3

Rockwell Automation Publication 2711P-IN032A-EN-P - July 2014

4. Secure the terminal in the panel.

a. Verify the orientation of the mounting levers.

The direction that you rotate each mounting lever is different for each terminal size.

See Mounting Lever Orientation and Lock Sequence on page 2.

b. Hold the first mounting lever in the locking sequence vertical to the slot and insert

its knob into the large end of the slot.

c. Slide the mounting lever to a notch that is one or two positions greater than the final

locking position for your panel thickness.

If the final locking position is 1, slide the mounting lever to position 2 or 3.

d. Rotate the mounting lever until its flat side comes in contact with the panel.

e. Repeat steps athrough dfor the remaining mounting levers.

IMPORTANT

Use catalog number 2711P-RMCS mounting levers for PanelView Plus 7 standard terminals. Do

not use these mounting levers with any other PanelView Plus terminals.

16 16

TIP

The mounting levers for PanelView Plus 7 standard

terminals are gray, similar to the color of the bezel.

Do not use black mounting levers; they are not

compatible with PanelView Plus 7 standard terminals.

1 6

TIP

Use an erasable marker or grease pencil to mark

the alignment marks for visibility of the slot

positions and to mark the final lock position.

TIP

The mounting leversare designed tobreak off the

pin if they are over torqued. This helps to prevent

damage to the bezel. If a pin is broken, turn the

mounting lever around and use the other pin to

continue the installation. See Mounting Lever

Orientation and Lock Sequence on page 2 for

restrictions.

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

5. Adjust each mounting lever to its final position by using the locking sequence in

Mounting Lever Orientation and Lock Sequence on page 2.

a. Unlock mounting lever one in the sequence

by rotating it away from the bezel.

b. With the mounting lever positioned

vertically to the slot, slide the mounting

lever to its final locking position as

determined by Mounting Lever Lock Position on page 1.

c. Carefully rotate the mounting lever back toward panel.

d. Repeat steps athrough cto lock the remaining mounting levers in the final position.

6. Inspect all mounting levers to make sure each lever is in the correct locked position.

Additional Resources

These documents contain additional information concerning related products from Rockwell

Automation.

You can view or download publications at http://www.rockwellautomation.com/literature/. To

order paper copies of technical documentation, contact your local Allen-Bradley distributor or

Rockwell Automation sales representative.

IMPORTANT

All mounting levers must be in the correct and same locked position to provide an adequate

gasket seal between the terminal and the panel. Rockwell Automation assumes no

responsibility for water or chemical damage to the terminal or other equipment within the

enclosure because of improper installation.

Resource Description

PanelView Plus 7 Standard Terminals User Manual,

publication 2711P-UM007

Provides details on how to install, configure, and operate the PanelView

Plus 7 standard terminals.

The notch on the outside of mounting lever shows its locked position.

This view shows the mounting levers locked in position 1.

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

yekat[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

info@klinkmann.fi

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected].ua

Andere Handbücher für PanelView Plus 7

Inhaltsverzeichnis

Andere Allen-Bradley Touch-Terminal Handbücher

Allen-Bradley

Allen-Bradley 1797-TB3S Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 1200 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711-K6C series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 8510SA-TP Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 6 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 6 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 800 2711R-T4T Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 7 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MobileView 2711T-B10R1K1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 5500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 2711P Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-PT1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 600 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711-K5A series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 2711C-F2M Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O SCANport 1203-FB Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 2711P-RW1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley DeviceNet 1790D-T16BV0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 6 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711P Gebrauchsanweisung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung