Alliance Laundry Systems 505048R2 Betriebsanleitung

Installation and Operation

Dryer

Metered Commercial

Electric and Gas Models

Part No. 505048R2

May 1998

NOTA: El manual en español aparece después del manual en inglés.

INUSE

PERMPRESS

NORMALFLUFF

(NOHEAT)

DELICATE

PUSH TO START

FABRIC SELECTOR

504210

OPERATINGINSTRUCTIONS

CLEAN LINT FILTER AFTER EACH LOAD

SelectFabricType(heatsetting)

NORMAL,PERMPRESS,

DELICATE,FLUFF(noheat)

LoadClothes.

InsertCoin(s)/Card.

ToStartDryer-CloseDoorandPushStart.

ToStopDryerDuringCycle-OpenDoor.

ToRestartDryer-CloseDoorandPushStart.

DryingCycleisCompleteWhen

PanelLightGoesOff.

D384IE1B

505048 1

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the dryer changes ownership, be

sure this manual accompanies the dryer.)

IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be

followed if the dryer user smells gas. The gas utility instructions plus the SAFETY and

WARNING note directly above must be posted in a prominent location near the dryer for

customer use.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

– Do not try to light any appliance.

– Do not touch any electrical switch; do not use any phone in your building.

– Clear the room, building or area of all occupants.

– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

– If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency or

the gas supplier. W052

FOR YOUR SAFETY, the information in this manual must be followed to minimize the

risk of fire or explosion or to prevent property damage, personal injury or death. W033

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

2505048

Replacement Parts . . .

If replacement parts are required, contact the source

where you purchased your dryer, or contact

Alliance Laundry Systems LLC

Shepard Street

P.O. Box 990

Ripon, WI 54971-0990

Phone:

(920) 748-3950

for the name and address of the nearest authorized parts

distributor.

Table of

Contents

Replacement Parts ............................................................................... 2

Important Safety Instructions.............................................................. 3

Roughing In Dimensions ..................................................................... 5

Additional Security .............................................................................. 6

Slide Extension ..................................................................................... 6

Timer Cams .......................................................................................... 6

Coin Slide Guards ................................................................................ 7

Before You Start ................................................................................... 8

Installing the Dryer

STEP 1 – Position and Level the Dryer ........................................... 9

STEP 2 – Connect Dryer Exhaust System .......................................9

STEP 3 – Connect Gas Supply Pipe............................................... 10

STEP 4 – Connect Electrical Plug.................................................. 11

STEP 5 – Wipe Out Inside of Dryer............................................... 12

STEP 6 – Plug in the Dryer ............................................................12

STEP 7 – Check Installation...........................................................12

Heat Source Check ............................................................................. 13

Reversing Door Procedure ................................................................ 14

Manufactured (Mobile) Home Installation ...................................... 15

Electrical Requirements (Electric Dryers) ....................................... 16

Electrical Connection

Three-Wire Power Cord ................................................................. 17

Four-Wire Power Cord .................................................................. 19

Electrical Requirements (Gas Dryers) ............................................. 21

Gas Requirements ............................................................................. 23

Location Requirements ..................................................................... 24

Dryer Exhaust Requirements ........................................................... 25

Multi-Dryer Installation Exhaust Requirements ............................. 28

Lint Filter............................................................................................. 31

Motor Overload Protector.................................................................. 31

Operation Instructions For Electromechanical Dryers .................. 32

Operation Instructions For Electroic Control Dryers .................... 34

User-Maintenance Instructions ......................................................... 37

For Energy Conservation ................................................................... 37

Before You Call for Service ................................................................ 38

Information for Handy Reference .................................................... 39

Installer Check .................................................................... Back Cover

the written permission of the publisher.

505048 3

IMPORTANT SAFETY INSTRUCTIONS

(SAVE THESE INSTRUCTIONS)

1. Read all instructions before using the dryer.

2. Refer to the GROUNDING INSTRUCTIONS in

the INSTALLATION manual for the proper

grounding of the dryer.

3. Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, other flammable

or explosive substances as they give off vapors

that could ignite or explode.

4. Do not allow children to play on or in the dryer.

Close supervision of children is necessary when

the dryer is used near children. This is a safety

rule for all appliances.

5. Before the dryer is removed from service or

discarded, remove the door to the drying

compartment.

6. Do not reach into the dryer if the cylinder is

revolving.

7. Do not install or store the dryer where it will be

exposed to water and/or weather.

8. Do not tamper with the controls.

9. Do not repair or replace any part of the dryer, or

attempt any servicing unless specifically

recommended in the user-maintenance

instructions or in published user-repair

instructions that you understand and have the

skills to carry out.

10. Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

11. To reduce the risk of fire, DO NOT DRY plastics

or articles containing foam rubber or similarly

textured rubberlike materials.

12. ALWAYS clean the lint filter after every load. A

layer of lint in the filter reduces drying efficiency

and prolongs drying time.

13. Keep area around the exhaust opening and

adjacent surrounding area free from the

accumulation of lint, dust and dirt.

14. The interior of the dryer and the exhaust duct

should be cleaned periodically by qualified

service personnel.

15. If not installed, operated and maintained in

accordance with the manufacturer’s instructions

or if there is damage to or mishandling of this

product’s components, use of this product could

expose you to substances in the fuel or from fuel

combustion which can cause death or serious

illness and which are known to the State of

California to cause cancer, birth defects or other

reproductive harm.

16. Dryer will not operate with the loading door

open. DO NOT by-pass the door safety switch by

permitting the dryer to operate with the door

open. The dryer will stop tumbling when the door

is opened. Do not use the dryer if it does not stop

tumbling when the door is opened or starts

tumbling without pressing the START

mechanism. Remove the dryer from use and call

the service person.

17. Do not put articles soiled with vegetable or

cooking oil in the dryer, as these oils may not be

removed during washing. Due to the remaining

oil, the fabric may catch on fire by itself.

18. To reduce the risk of fire, DO NOT put clothes

which have traces of any flammable substances

such as machine oil, flammable chemicals,

thinner, etc., or anything containing wax or

chemicals such as in mops and cleaning cloths, or

anything dry-cleaned at home with a dry-

cleaning solvent in the dryer.

19. Use the dryer only for its intended purpose,

drying clothes.

20. Always disconnect the electrical power to the

dryer before attempting service. Disconnect the

power cord by grasping the plug, not the cord.

21. Replace worn power cords and/or loose plugs.

22. Install this dryer according to the

INSTALLATION INSTRUCTIONS. All

connections for electrical power, grounding and

gas supply must comply with local codes and be

made by licensed personnel when required. Do

not do it yourself unless you know how!

23. Remove laundry immediately after the dryer

stops.

To reduce the risk of fire, electric shock, or

injury to persons when using your dryer,

follow these basic precautions:

W034

WARNING

(continued))

4505048

24. Always read and follow manufacturer’s

instructions on packages of laundry and cleaning

aids. Heed all warnings or precautions. To reduce

the risk of poisoning or chemical burns, keep

them out of reach of children at all times

(preferably in a locked cabinet).

25. Do not tumble fiber glass curtains and draperies

unless the label says it can be done. If they are

dried, wipe out the cylinder with a damp cloth to

remove particles of fiber glass.

26. ALWAYS follow the fabric care instructions

supplied by the garment manufacturer.

27. Never operate the dryer with any guards and/or

panels removed.

28. DO NOT operate the dryer with missing or

broken parts.

29. DO NOT by-pass any safety devices.

30. Failure to install, maintain, and/or operate this

machine according to the manufacturer’s

instructions may result in conditions which can

produce bodily injury and/or property damage.

IMPORTANT: Solvent vapors from dry-cleaning

machines create acids when drawn through the heater

of the drying unit. These acids are corrosive to the

dryer as well as to the laundry load being dried. Be

sure make-up air is free of solvent vapors.

IMPORTANT: Have your dryer installed properly.

Don’t do it yourself unless you know how!

NOTE: The WARNING and IMPORTANT

SAFETY INSTRUCTIONS appearing in this manual

are not meant to cover all possible conditions and

situations that may occur. Common sense, caution

and care must be exercised when installing,

maintaining, or operating the dryer.

Always contact your dealer, distributor, service agent or

the manufacturer about any problems or conditions you

do not understand.

505048 5

Roughing In Dimensions . . .

NOTE: Side, rear and bottom exhaust openings are

four inch (10.2 cm) ducting. Gas models cannot be

vented out left side of cabinet because of burner

housing.

IMPORTANT: The dryer should have sufficient

clearance around it for needed ventilation and for the

ease of installation and servicing. For maximum

drying performance, we recommend that more

clearance be allowed around the dryer than the

clearances that are listed throughout this manual.

ELECTRIC MODELS

D368IE3A

23.5"

(59.7 cm)

*43.2" (109.7 cm)

28"

(71.1 cm)

.4"

(1.1 cm) 26.9"

(68.3 cm)

7.7"

(19.6 cm)

4.0"

(10.2 cm)

15.4"

(39.1 cm)

4.0"

(10.2 cm)

* WITH LEVELING LEGS TURNED INTO BASE.

2.0"

(5.1 cm)

GAS MODELS

D369IE3A

23.5"

(59.7 cm)

*43.2" (109.7 cm)

28"

(71.1 cm)

.4"

(1.1 cm) 26.9"

(68.3 cm)

15.4"

(39.1 cm)

4.0"

(10.2 cm)

* WITH LEVELING LEGS TURNED INTO BASE.

3/8"

NPT GAS

CONNECTION

2.8"

(7 cm)

2.3"

(6 cm)

4.0"

(10.2 cm)

7.7"

(19.6 cm)

2.0"

(5.1 cm)

6505048

Additional Security . . .

Torx security screws are available (as optional equipment

at extra cost) for securing lower access panel to dryer

base. Order part number 62853.

A Torx bit, part number 282P4, is available (as optional

equipment at extra cost) for installing the Torx security

screws.

A Torx bit holder, part number 24161, is available (as

optional equipment at extra cost) to be used with the Torx

bit.

Slide Extension . . .

(Coin Slide Models Only)

Remove slide extension, screws and lockwashers from

the accesssories bag and install the extension on the top

of the coin slide.

IMPORTANT: Slide extension must be attached to

top side of the coin slide to make it long enough to

activate the accumulator.

NOTE: This dryer, as shipped from the factory, does

not include the coin slide, coin drawer, lock or keys.

This coin slide kit (or parts) must be ordered, at extra

cost, according to the purchaser’s requirements

direct from the coin kit manufacturer of your choice.

Timer Cams . . .

(Coin Slide Models Only)

The dryer timers are factory equipped with a 45 minute

timing cam. If this drying time is not suitable to your

installation, the following cams can be found in the

accessories bag.

ELECTRIC DRYERS

1-53242 Cam (30 Minutes)

1-53240 Cam (60 Minutes)

GAS DRYERS

1-53242 Cam (30 Minutes)

A 60 minute timing cam, Part No. 53240, is available for

the gas dryer as optional equipment at extra cost.

505048 7

Coin Slide Guards . . .

(Coin Slide Models Only)

Using serrated hex head screws from accessories bag,

install coin slide guard, to front of control cabinet. See

illustration.

A special security screw kit is available (as optional

equipment at extra cost) for securing the coin slide guard

and front panel to front of dryer. Order Security Kit No.

298P3. A special driver, part number 56217, is available

(as optional equipment at extra cost) for installing the

special security screws.

NOTE: Coin slides and coin drawers are shown for illustration only. You must obtain them locally.

OPERATING INSTRUCTIONS

CLEAN LINT FILTER AFTER EACH LOAD

IN USE

PERM PRESS

NORMAL FLUFF

(NO HEAT)

DELICATE

PUSH TO START

FABRIC SELECTOR

504210

Select Fabric Type (heat setting)

NORMAL, PERM PRESS,

DELICATE, FLUFF (no heat)

Load Clothes.

Insert Coin(s)/Card.

To Start Dryer - Close Door and Push Start.

To Stop Dryer During Cycle - Open Door.

To Restart Dryer - Close Door and Push Start.

Drying Cycle is Complete When

Panel Light Goes Off.

COIN

SLIDE

GUARD

SERRATED

HEX HEAD

SCREWS

D382IE3B

8505048

Before You Start . . .

Tools

For most installations, the basic tools you will need are:

Exhaust

Use rigid metal duct and exhaust the dryer to the outside

by the shortest route possible.

NOTE: For more detailed information, refer to

Section on Dryer Exhaust Requirements.

Electrical

•ELECTRIC DRYER Dryer needs a 3 or 4 wire 120/

240 or 120/208 Volt, 60 Hertz, AC single Phase

electrical supply.

•GAS DRYER

Dryer needs a 120 Volt, 60 Hertz, polarized 3-slot

effectively grounded receptacle.

NOTE: For more detailed information, refer to

Section on Electrical Requirements.

Gas

Dryer is equipped for Natural Gas with a 3/8" NPT gas

supply connection. For more detailed information, refer

to Section on Gas Requirements.

Location

Place the dryer on a solid floor with an adequate air

supply. For more detailed information, refer to Section on

Location Requirements.

D074IE1F

DUCT TAPE TEFLON TAPE

WRENCH

LEVEL

SCREWDRIVERS

D367IE1A

505048 9

Installing the Dryer . . .

Step 1:

Position and Level

the Dryer

For further assistance refer to Section on Location

Requirements.

Install dryer before washer. This allows room for

attaching exhaust duct.

Install the four rubber cups found in the accessory bag.

Place the dryer in position, and adjust the legs until the

dryer is level.

Step 2:

Connect Dryer Exhaust System

For further assistance refer to Sections on Location

Requirements and Dryer Exhaust Requirements.

•DO NOT use plastic or thin foil flexible ducting.

•Locate dryer so exhaust duct is as short as possible.

•Be certain old ducts are cleaned before installing your

new dryer

•Use 4" (10.2 cm) diameter rigid or flexible metal duct.

•Use as few elbows as possible.

•Use duct tape on all joints.

•Failure to exhaust dryer properly will void

warranty.

NOTE: Venting materials are not supplied with the

dryer (obtain locally).

INUSE

PERMPRESS

NORMALFLUFF

(NOHEAT)

DELICATE

PUSHTO START

FABRICSELECTOR

504210

OPERATINGINSTRUCTIONS

CLEANLINTFILTERAFTEREACHLOAD

SelectFabricType(heatsetting)

NORMAL,PERMPRESS,

DELICATE,FLUFF(noheat)

LoadClothes.

InsertCoin(s)/Card.

ToStartDryer-CloseDoorandPushStart.

ToStopDryerDuringCycle-OpenDoor.

ToRestartDryer-CloseDoorandPushStart.

DryingCycleisCompleteWhen

PanelLightGoesOff.

D384IE1A

LEVEL

DRYER

BASE

LEVELING

LEG

RUBBER

CUP

A clothes dryer produces combustible lint. To

reduce the risk of fire and combustion gas

accumulation the dryer MUST be exhausted

to the outdoors.

W116

WARNING

D367IE1B

DO DON'TD370IE1A

(continued))

Inhaltsverzeichnis

Sprachen:

Andere Alliance Laundry Systems Trockner Handbücher

Alliance Laundry Systems

Alliance Laundry Systems SDE907 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems DRY2195N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Huebsch DR5102WG Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems continuity Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems T463PE1A Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LES19A SERIES Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems D355IE1B Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 70269701R4 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems T433I Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DC0220SFG Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY2024N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems PD3JGBGS403UG01 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems D677I Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems LES33A F4562 Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CA170L Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HAT30N Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRYING TUMBLERS 70269501R3 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 70223701R2 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CHD25G2-CA025L Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen DR7004WE Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Drying Tumblers 50 Pound Capacity 75 Pound Capacity Model Identification Part No.... Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems AE Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen DR5003WG Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung

Samsung

Samsung DV431AEPXAC Bedienungsanleitung