Alliance Laundry Systems ATB50CG Betriebsanleitung

www.comlaundry.com

Troubleshooting

Part No. 70410501

September 2007

Drying Tumblers

50 Pound Capacity

75 Pound Capacity

Refer to Page 5 for Model Numbers

T012c

the expressed written consent of the publisher.

70410501 1

Table of

Contents

Section 1 – Safety Information ...............................................................3

Locating An Authorized Service Person ...............................................4

Section 2 – Introduction..........................................................................5

Model Identification ..............................................................................5

Customer Service...................................................................................6

Serial Plate Location..............................................................................6

Safety Warnings and Decals..................................................................7

Safety Precautions for Servicing Tumblers...........................................7

How A Tumbler Works.........................................................................8

Section 3 – Troubleshooting..................................................................10

1. Motor Does Not Start..................................................................11

2. Motor Overload Protector Cycles Repeatedly ............................13

3. Motor Runs But Cylinder Does Not Turn...................................14

4. Motor Does Not Stop..................................................................15

5. Heating Element Does Not Heat Or Burner Does Not Ignite

– Gas and Electric Models ..........................................................16

6. Pilot Does Not Ignite – Standing Pilot Ignition Gas Models......18

7. Pilot Goes Out – Standing Pilot Ignition Gas Models ................19

8. Igniter Does Not Shut Off After Gas Ignition

– Automatic Pilot Ignition Gas Models ......................................20

9. Gas Supply Sufficient But Igniter Does Not Glow

– Glow-Bar Ignition Gas Models................................................21

10. Igniter Glows, Sensor Opens But No Ignition

– Johnson Controls System Gas Models.....................................22

11. Igniter Glows, Sensor Opens But No Ignition

– White Rodgers Glow-Bar Ignition Gas Models.......................23

12. Burner Ignites and Goes Out Repeatedly

– Glow-Bar Ignition Gas Models................................................24

13. Heating Element or Burner Shuts-Off Prematurely....................25

14. Heating Element or Burner Repeatedly Cycles Off On

High Limit Thermostat................................................................26

15. Heating Element or Burner Does Not Shut-Off..........................27

16. Clothes Do Not Dry ....................................................................28

17. Tumbler Overheating ..................................................................29

18. Burners Not Burning Properly – Gas Models.............................30

19. Loading Door Opens During Operation......................................31

20. Tumbler Runs But No Steam To Coils – Steam Models ............32

21. Water In Steam Line – Steam Models ........................................33

22. Troubleshooting Electronic Control Models...............................34

23. Tumbler Will Not Start, Time on Drying Timer,

Door Closed – Manual Timer Models ........................................36

24. Motor Runs, Time on Drying Timer But No Heat......................37

25. No Spark to Pilot Burner – Electronic Pilot Ignition Models.....39

26. Spark to Pilot Burner, No Pilot Flame

– Electronic Pilot Ignition Models..............................................40

27. Spark To Pilot Burner, Pilot Lights, No Main Burner

– Electronic Pilot Ignition Models..............................................41

270410501

28. Igniter Does Not Glow – Johnson Controls

Glow-Bar System........................................................................42

29. Igniter Glows Constantly – Johnson Controls and

White Rodgers Glow-Bar System...............................................43

30. Igniter Glows, Cycles Off But Burner Does Not Ignite

– Johnson Controls Glow-Bar System........................................44

31. Igniter Does Not Glow – White Rodgers Glow-Bar System......45

32. Igniter Glows, Cycles Off But Burner Does Not Ignite

– White Rodgers Glow-Bar System............................................46

33. Igniter Sparks, No Main Burner Ignition

– Instant Electronic Ignition........................................................47

34. CSH OM Models: No Heat With Cycle Selected,

Unit Running and Calling For Heat............................................48

35. OM Models: No Start With Cycle Selected, Start Button

Pressed and Door Closed ............................................................50

36. OM Models: No Display After Selecting One Of The

ON/SELECT Keys......................................................................52

37. CE OM Models: No Heat With Cycle Selected, Unit

Running and Calling For Heat ....................................................53

38. CG OM Models: No Heat With Cycle Selected, Unit

Running and Calling For Heat ....................................................55

39. OM Models: No Fan Motor Rotation With Cycle Selected

and Start Pressed.........................................................................57

40. MM Models: Fan Motor Does Not Run With Door Closed,

Cycle Selected and Start Button Pressed ....................................58

41. MM Models: Cylinder Motor Does Not Run or Reverse With

Door Closed, Cycle Selected and Start Button Pressed In

Reversing Mode or Nonreversing Mode.....................................59

42. MM Models: No Heat With Cycle Selected, Unit Running

and Calling For Heat...................................................................61

43. MM Models: No Heat With Cycle Selected, Unit Running

and Calling For Heat...................................................................63

44. OM Reversing Models: No Cylinder Rotation or Reversing

Capabilities..................................................................................65

45. MM Models: No Display After Pressing the ON/SELECT

Keys ............................................................................................67

46. MM Models: Motor Does Not Run With Door Closed, Cycle

Selected and Start Button Pressed...............................................68

47. MM Models: Cylinder Motor Does Not Run or Reverse With

Door Closed, Cycle Selected and Start Button Pressed In

Reversing Mode or Nonreversing Mode.....................................69

48. MM Nonreversing Models: Motor Does Not Run With Door

Closed, Cycle Selected and Start Button Pressed .......................71

49. CD Models: No Start With Vend Satisfied and Start Button

Pushed.........................................................................................73

50. CD Models: No Heat With Vend Satisfied and Unit Running ...75

51. CD Models: No Heat With Vend Satisfied and Unit Running ...77

52. CD Models: No Start With Vend Satisfied and Start Button

Pushed.........................................................................................79

53. CD Models: No Start With Vend Satisfied and Start Button

Pushed.........................................................................................81

Section 4 – Adjustments........................................................................82

54. Cylinder Clearance......................................................................82

70410501 3

Section 1

Safety Information

Throughout this manual and on machine decals, you

will find precautionary statements (“CAUTION”,

“WARNING”, and “DANGER”) followed by specific

instructions. These precautions are intended for the

personal safety of the operator, user, servicer, and those

maintaining the machine.

Additional precautionary statements (“IMPORTANT”

and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used

to inform the reader of specific procedures where

minor machine damage will occur if the procedure

is not followed.

NOTE: The word “NOTE” is used to communicate

installation, operation, maintenance or servicing

information that is important but not hazard

related.

In the interest of safety, some general precautions

relating to the operation of this machine follow.

DANGER indicates the presence of a

hazard that will cause severe personal

injury, death, or substantial property

damage if the danger is ignored.

DANGER

WARNING indicates the presence of a

hazard that can cause severe personal

injury, death, or substantial property

damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a

hazard that will or can cause minor

personal injury or property damage if the

caution is ignored.

CAUTION

• Failure to install, maintain and/or operate

this product according to the

manufacturer’s instructions may result in

conditions which can produce serious

injury, death and/or property damage.

• Do not repair or replace any part of the

product or attempt any servicing unless

specifically recommended or published in

this Service Manual and unless you

understand and have the skills to carry

out the servicing.

• Whenever ground wires are removed

during servicing, these ground wires

must be reconnected to ensure that the

product is properly grounded and to

reduce the risk of fire, electric shock,

serious injury or death.

W006R2

WARNING

470410501

Safety Information

IMPORTANT INFORMATION: During the

lifetime of a tumbler, it may require service. The

information contained in this manual was written

and is intended for use by qualified service

technicians who are familiar with the safety

procedures required in the repair of a tumbler, and

who are equipped with the proper tools and testing

equipment.

NOTE: The WARNING and IMPORTANT

instructions appearing in this manual are not meant

to cover all possible conditions and situations that

may occur. It must be understood that common

sense, caution and carefulness are factors which

CANNOT be built into this tumbler. These factors

MUST BE supplied by the person(s) installing,

maintaining or operating the tumbler.

Always contact your dealer, distributor, service agent

or the manufacturer on any problems or conditions you

do not understand.

Locating An Authorized Service

Person

Alliance Laundry Systems is not responsible for

personal injury or property damage resulting from

improper service. Review all service information

before beginning repairs.

Warranty service must be performed by an

authorized technician, using authorized factory

parts. If service is required after the warranty

expires, Alliance Laundry Systems also

recommends contacting an authorized technician

and using authorized factory parts.

To reduce the risk of electric shock, fire,

explosion, serious injury or death:

• Disconnect electric power to the tumbler

before servicing.

• Never start the tumbler with any guards/

panels removed.

• Whenever ground wires are removed

during servicing, these ground wires

must be reconnected to ensure that the

tumbler is properly grounded.

W240

WARNING

Repairs that are made to your products by

unqualified persons can result in hazards

due to improper assembly or adjustments

subjecting you or the inexperienced person

making such repairs to the risk of serious

injury, electrical shock or death.

W007

WARNING

If you or an unqualified person perform

service on your product, you must assume

the responsibility for any personal injury or

property damage which may result. The

manufacturer will not be responsible for

any injury or property damage arising from

improper service and/or service

procedures.

W008

CAUTION

70410501 5

Section 2

Introduction

Model Identification

Information in this manual is applicable to these models:

Gas Steam/Thermal Oil Electric

Pound

ATB50CG

DCB50CG

DCB50EG

DTB50CG

DTB50EG

JC50CG

JC50EG

JCB50CG

JCB50EG

JT37CG

JT37CGI

JT37EG

JT37EGI

JT50CG

JT50CGI

JT50EG

JT50EGI

JTB50CG

JTB50EG

SC50CG

SC50EG

SCB50CG

SCB50EG

ST37CG

ST37CGI

ST37EG

ST37EGI

ST50CGI

ST50EGI

STB50CG

STB50EG

TKD50CGMT

ATB50CSH

DCB50CSH

DTB50CSH

DTB50CSL

JC50CSH

JCB50CSH

JT37CSH

JT37CSL

JT50CSH

JT50CSL

JTB50CSH

JTB50CSL

SC50CSH

SCB50AT

SCB50CSH

ST37CSH

ST37CSL

ST50CSH

ST50CSL

STB50CSH

STB50CSL

DCB50CE

DTB50CE

JC50CE

JCB50CE

JT37CE

JT50CE

JTB50CE

SC50CE

SCB50CE

ST37CE

ST50CE

STB50CE

TKD50CEMT

Pound

ATB75CG

DCB75CG

DCB75FG

DTB634

DTB75CG

DTB75EG

DTB75FG

JCB75CG

JT75CG

JT75EG

JTB75CG

JTB75EG

SCB75CG

ST75CG

STB634

STB75CG

STB75EG

ATB75CSH

DCB75CSH

DCB75CSL

DTB75CSH

DTB75CSL

JCB75CSH

JCB75CSL

JT75CSH

JT75CSL

JTB75CSH

JTB75CSL

SCB75CSH

SCB75CSL

ST75CSH

ST75CSL

STB75CSH

STB75CSL

DCB75CE

DTB75CE

JCB75CE

JT75CE

JTB75CE

SCB75CE

ST75CE

STB75CE

670410501

Introduction

Customer Service

If literature or replacement parts are required, contact

the source from whom the machine was purchased or

contact Alliance Laundry Systems at (920) 748-3950

for the name and address of the nearest authorized

parts distributor.

For technical assistance, call (920) 748-3121.

Serial Plate Location

When calling or writing about your product, be sure to

mention model and serial numbers. Model and serial

numbers are located on serial plate(s) as shown.

T419IE3B

70410501 7

Introduction

Safety Warnings and Decals

SAFETY WARNINGS and decals have been provided

in key locations to remind you of important precautions

for the safe operation and maintenance of your tumbler.

Please take the time to review these warnings before

proceeding with service work.

All decals have been designed and applied to withstand

washing and cleaning. Decals should be checked

periodically to be sure they have not been damaged,

removed, or painted. Refer to Parts Manual for

ordering replacement decals.

Safety Precautions for Servicing Tumblers

• Disconnect electrical service.

• Shut off supply gas valve before servicing gas

components.

• Control panel and access panel MUST be

reinstalled after inspection or servicing of

tumbler is completed.

• Use a non-corrosive leak detection fluid to check

all pipe connections for gas leaks. DO NOT USE

AN OPEN FLAME TO CHECK FOR GAS

LEAKS!

• Chain/drive guard MUST be reinstalled after

inspection or servicing of tumbler is completed.

• Belt guard MUST be reinstalled after inspection

or servicing of tumbler is completed.

• Contactor box cover MUST be reinstalled after

inspection or servicing of electric and/or reversing

tumbler is completed.

• Loading door switch MUST be operational before

putting tumbler into service.

• Junction box cover MUST be reinstalled after

inspection or servicing of tumbler is completed.

870410501

Introduction

How A Tumbler Works

The tumbler uses heat, air and movement to dry

loads of laundry.

When the motor is started, the exhaust fan pulls

fresh air in through the air intake and over the heat

source (burner flame for gas, heating element for

electric, and coil for steam).

The heated air moves into the cylinder, where it is

circulated through the laundry by the tumbling

action of the cylinder.

The air then passes through the lint filter, exhaust

fan, and is vented to the outdoors.

NOTE: In Energy Saver Models, some of the

exhaust air is recirculated. Refer to illustration on

next page.

Fresh Air

Combustion Air

Mixed Air

Exhaust Air T008CE1A

Standard Models

Dieses Handbuch passt für folgende Modelle

107

Inhaltsverzeichnis

Andere Alliance Laundry Systems Trockner Handbücher

Alliance Laundry Systems

Alliance Laundry Systems AES17AWF Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems Huebsch DR5102WG Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems T477C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 512906 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 602004144 Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems 513123 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LES37AW Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems EE1010 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Clothes dryers Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DCB30CG Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Clothes Dryer Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LTS87A*H Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HSE117*C802 Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems 000 BTU Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 510977R9 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems Stacked Drying Tumbler Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems ADEE9BSS Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Pound Capacity Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DV6000WG Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems HAT30N Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Drying Tumbler Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY722C-SVG Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems DRY725C Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung