Alliance Laundry Systems AFNE9BSP113TN01 Bedienungsanleitung

Installation Instructions

for Frontload Washers

Original Instructions

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.speedqueen.com Part No. 804650ENR2

June 2016

Table of Contents

Washer Dimensions................................................................................ 4

Installation............................................................................................. 5

Before You Start............................................................................................. 5

Tools..........................................................................................................5

Parts Included............................................................................................. 5

Order of Installation Steps............................................................................5

Position Unit Near Installation Area................................................................. 5

Remove Shipping Materials.............................................................................5

Connect Fill Hoses..........................................................................................6

Water Supply Requirements......................................................................... 7

Connecting Hoses....................................................................................... 7

Connect Drain Hose to Drain Receptacle.......................................................... 7

Standpipe Installation.................................................................................. 8

Wall Installation.......................................................................................... 8

Laundry Tub Installation..............................................................................8

Position and Level the Washer......................................................................... 9

Wipe Out Inside of Wash Drum........................................................................9

Plug In the Washer..........................................................................................9

Electrical Requirements............................................................................... 9

Earth/Ground Instructions.......................................................................... 10

Check Installation......................................................................................... 11

Installer Checklist.................................................................................12

written consent of the publisher.

DO NOT COPY or TRANSMIT

3 Part No. 804650ENR2

Washer Dimensions

FLW2331N_SVG

Figure 1

A 24.06 in. [611 mm]

B 40.42 in. [1027 mm]

C 32 in. [813 mm]

D 39.61 in. [1006 mm]

E * 14.6 in. [371 mm]

F 26.875 in. [683 mm]

G 2.04 in. [52 mm]

H 27.73 in. [704 mm]

I (with door closed) 1.59 in. [40 mm]

J 13.1 in. [333 mm]

* For ADA compliance turn legs out from base 0.5 inches.

Washer Dimensions

DO NOT COPY or TRANSMIT

4 Part No. 804650ENR2

Installation

Before You Start

Tools

For most installations, the basic tools you will need are:

FLW2376N_SVG

1. Safety Glasses

2. Wood Block

3. Wrench

4. Screwdriver

5. Pliers

6. Socket Wrench

7. Gloves

8. Level

Figure 2

NOTE: If the washer is delivered on a cold day (below

freezing), or is stored in an unheated room or area dur-

ing the cold months, do not attempt to operate it until

the washer has had a chance to warm up.

NOTE: Install dryer before washer. This allows room for

attaching exhaust duct.

NOTE: Some moisture in the wash drum is normal. Wa-

ter is used during testing at the manufacturer.

NOTE: This appliance is suitable for use in countries

having a warm, damp climate.

Parts Included

An accessories bag has been shipped inside your washer. It in-

cludes:

• Two fill hoses with washers and filter screens

• Four rubber feet

• Beaded strap

• Installation Instructions

• User’s Guide

• Warranty Bond

Order of Installation Steps

The proper order of steps must be followed to ensure correct in-

stallation. Refer to the list below when installing your unit.

1. Position washer near the installation area.

2. Remove the shipping materials.

3. Connect the fill hoses.

4. Connect the drain hose to the drain receptacle.

5. Position and level the washer.

6. Wipe out inside of the washer.

7. Supply injection models only: Connect external supplies to

washer.

8. Plug in the washer.

9. Check installation.

Position Unit Near Installation Area

Move unit so that it is within 4 feet [1.2 meters] of the desired

area of installation.

NOTE: For best performance and to minimize vibration

or movement, install washer on a solid, sturdy and lev-

el floor. Some floors may need to be reinforced, espe-

cially on a second floor or over a basement. Do not in-

stall the washer on carpeting, soft tile or other weakly

supported structures.

Remove Shipping Materials

1. Remove two screws at bottom of front access panel. Rotate

bottom of panel out and remove panel.

Installation

DO NOT COPY or TRANSMIT

5 Part No. 804650ENR2

FLW2378N_SVG

Figure 3

2. Remove two 9/16 inch bolts and washers holding shipping

brace to weight.

3. Remove two 9/16 inch bolts and washers holding shipping

brace to washer base and remove brace.

FLW2296N_SVG1

Figure 4

4. Go to rear of washer and pull label from rear shipping bolts.

5. Remove two 9/16 inch bolts. Unscrew each bolt while apply-

ing forward pressure just until bolt stops unthreading. Work

each bolt and spacer out by hand using a circular motion.

NOTE: Avoid backing bolts out completely or

spacers might fall into cabinet.

FLW2297N_SVG1

Figure 5

6. Insert two plugs included in accessories bag into rear shipping

bolt holes.

FLW2358N_SVG

Figure 6

7. Replace front access panel.

8. Save all shipping materials. They must be reinstalled any time

washer is moved more than four feet.

IMPORTANT: Do not lift or transport unit from front

or without shipping materials installed. Refer to the

User’s Guide for proper instructions on reinstalling

the shipping materials.

Connect Fill Hoses

WARNING

Under certain conditions, hydrogen gas may be pro-

duced in a hot water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLO-

SIVE. If the hot water system has not been used for

such a period and before using the washer, turn on

all hot water faucets and let the water flow from each

for several minutes. This will release any accumulat-

ed hydrogen gas. The gas is flammable. Do not

smoke or use an open flame during this time.

W029

Installation

DO NOT COPY or TRANSMIT

6 Part No. 804650ENR2

Water Supply Requirements

Water supply faucets must fit standard 3/4 inch [19 mm] female

garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-

ON CONNECTIONS.

NOTE: Water supply faucets should be readily accessi-

ble to permit turning them off when washer is not being

used.

Recommended cold water temperature is 50° to 75° Fahrenheit

[10° to 24° Celsius]. Recommended maximum hot water temper-

ature is 125° Fahrenheit [51° Celsius]. Warm water is a mixture

of hot and cold water. Warm water temperature is dependent upon

the water temperature and the pressure of both the hot and cold

water supply lines.

WARNING

To prevent personal injury, avoid contact with inlet

water temperatures higher than 125° Fahrenheit [51°

Celsius] and hot surfaces.

W748

Maximum flow rate for all water temperatures is 2.5 gallons per

minute [9.46 liters per minute] ± 15%.

Water pressure must be a minimum of 20 to a maximum of 120

pounds per square inch [minimum of 138 to a maximum of 827

kPa] static pressure measured at the faucet.

NOTE: Water pressure under 20 pounds per square

inch [138 kPa] will cause an extended fill time in the

washer and may not properly flush out the detergent

dispenser.

Turn on the water supply faucets and flush the lines for approxi-

mately two minutes to remove any foreign materials that could

clog the screens in the water mixing valve. This is especially im-

portant when installing your washer in a newly constructed or

renovated building. Build-up may have occurred during construc-

tion.

Connecting Hoses

1. Remove the two plain rubber washers and two filter screens

from the accessories bag.

2. Install them into each end of the fill hoses as shown in Figure

7 . The screen must be facing outward.

3. Screw hose couplings with the filter screens onto the water

faucets until they are finger-tight. Use the red color-coded

hose for the hot water connection and the blue color-coded

hose for the cold water connection.

4. Then, using a pliers, screw approximately 1/4 turn.

5. Screw hose couplings from other end of hoses onto the water

mixing valve until they are finger-tight. Make sure the red

color-coded hose from the hot water faucet goes to the water

mixing valve marked “H” and the blue color-coded hose from

the cold faucet goes to the valve marked “C”. Refer to Figure

Figure 7 .

6. Then, using a pliers, screw approximately 1/4 turn.

IMPORTANT: DO NOT cross thread or overtighten

couplings. This will cause them to leak.

7. Turn water on and check for leaks.

8. If leaks are found, turn off the water, unscrew hoses and rein-

stall them until there are no leaks.

IMPORTANT: Turn off water supply whenever there

will be an extended period of non-use.

FLW2304N_SVG1

COLD

HOT

1. Filter Screen (Screen must be facing outward)

2. Fill Hose

3. Rubber Washer (Plain)

4. Cold Water Connection

5. Hot Water Connection

6. Install this end of hose to valve connections at rear of

washer.

7. Install this end of hose to water supply faucet.

8. Faucet

Figure 7

IMPORTANT:

Hoses and other natural rubber parts deteriorate after

extended use. Hoses may develop cracks, blisters or

material wear from the temperature and constant high

pressure they are subjected to.

All hoses should be checked on a monthly basis for

any visible signs of deterioration. Any hose showing

the signs of deterioration listed above should be re-

placed immediately. All hoses should be replaced ev-

ery five years.

Connect Drain Hose to Drain Recepta-

cle

Remove the drain hose from its shipping position on the rear of

the washer by unhooking the hose from the retainer clamp and by

removing the shipping tape.

Installation

DO NOT COPY or TRANSMIT

7 Part No. 804650ENR2

Install the drain hose into the drain receptacle (standpipe, wall or

laundry tub) following the instructions below.

IMPORTANT: Drain receptacle must be capable of han-

dling a minimum of 1-1/4 inch [32 mm] outside diame-

ter drain hose.

Drain Flow Rate

Drain Height

Flow Rate

gallons per minute [lit-

ers per minute]

3 ft. [0.9 m] 8.6 [32.7]

5 ft. [1.5 m] 6.8 [25.9]

6 ft. [1.8 m] 6.0 [22.7]

7 ft. [2.1 m] 5.1 [19.5]

8 ft. [2.4 m] 4.0 [15.2]

Standpipe Installation

1. Place the drain hose into the standpipe.

2. Remove the beaded tie-down strap from accessories bag and

place around standpipe and drain hose and tighten strap to

hold hose to standpipe. Refer to Figure 8 . This will prevent

the drain hose from dislodging from drain receptacle during

use.

FLW2314N_SVG

1. 24 to 36 in. [610 to 914 mm] Recommended Height

2. Beaded strap from accessory bag

3. Standpipe 2 in. [51 mm] or 1-1/2 in. [40 mm]

Figure 8

Wall Installation

For installations of this type, the drain hose MUST be secured to

one of the fill hoses using the beaded strap from accessories bag.

Refer to Figure 9 .

NOTE: End of drain hose must not be below 24 in. [610

mm].

H023i_SVG

1. Drain Hose

2. Beaded Strap (tape if necessary)

3. Fill Hoses

Figure 9

Laundry Tub Installation

For this type of installation, the drain hose MUST be secured to

the stationary tub to prevent hose from disloding during use. Re-

fer to Figure 10 . Use the beaded strap (supplied in accessories

bag) to secure hose.

FLW2315N_SVG

1. Drain Hose

2. Beaded Strap (tape if necessary)

Figure 10

Installation

DO NOT COPY or TRANSMIT

8 Part No. 804650ENR2

Position and Level the Washer

WARNING

Washers elevated above floor level must be anch-

ored to that elevated surface, base or platform. The

material used to elevate the washer should also be

anchored to the floor to ensure that the washer will

not walk or that the washer can not be physically

pulled, tipped or slid from its installed position. Fail-

ure to do so may result in conditions which can pro-

duce serious injury, death and/or property damage.

W306

1. Position unit so it has sufficient clearance for installation and

servicing.

NOTE: Use of the dispenser drawer or washer door

as a handle in the transportation of the washer may

cause damage to the dispenser or door.

2. Place unit in position on a solid, sturdy and level floor. Instal-

ling the unit on any type of carpeting, soft tile or other weakly

supported structures is not recommended.

3. Place a level on the raised portion of cabinet top and check if

the unit is level from side to side and front to back.

4. If unit is not level, tilt unit to access the front and rear level-

ing legs. For easier access to leveling legs, prop up unit with a

wooden block.

5. Loosen 7/8 in. locknut and adjust legs by screwing into or out

of unit base until the unit is level from side to side and front

to back (using a level). Unit should not rock.

NOTE: Leveling legs can also be adjusted from in-

side the unit using an adjustable wrench.

6. Tighten the locknuts securely against the unit base. If the

locknuts are not tight, unit will move out of position during

operation.

NOTE: DO NOT slide unit across floor if the leveling

legs have been extended. Legs and base could be-

come damaged.

7. Remove rubber feet from accessories bag and place on all

four leveling legs.

8. Verify that unit doesn’t rock.

FLW2312N_SVG

1. Leveling Leg

2. Washer Base

3. Level

4. Wood Block

5. Locknut

6. Rubber Foot

Figure 11

Wipe Out Inside of Wash Drum

Prior to first wash, use an all purpose cleaner or a detergent

and water solution and a damp cloth to remove shipping dust

from inside of the washer.

FLW2316N_SVG

Figure 12

Plug In the Washer

Electrical Requirements

120 Volt, 60 Hertz with 3-Prong Earth/Ground Plug

NOTE: The wiring diagram is located in the control cab-

inet.

Installation

DO NOT COPY or TRANSMIT

9 Part No. 804650ENR2

WARNING

To reduce the risk of fire, electric shock, serious in-

jury or death, all wiring and protective earth/ground

connections MUST conform with the latest edition of

the National Electrical Code, ANSI/NFPA No. 70, and

such local regulations as might apply. It is the cus-

tomer’s responsibility to have the wiring, fuses and

circuit breakers installed by a qualified electrician to

make sure adequate electrical power is available to

the washer.

W824

When plugging in the washer:

• DO NOT overload circuits.

• DO NOT use an extension cord.

• DO NOT use an adapter.

• DO NOT operate other appliances on the same circuit. Use

separately fused 15 Amp circuits.

The washer is designed to be operated on a separate branch, po-

larized, three-wire, effective earth/ground, 120 Volt, 60 Hertz,

AC (alternating current), circuit protected by a 15 ampere fuse,

equivalent fusetron or circuit breaker.

The three-prong earth/ground plug on the power cord should be

plugged directly into a polarized three-slot effective earth/ground

receptacle rated 110/120 Volts AC (alternating current) 15 Amps.

Refer to Figure 13 to determine correct polarity of the wall recep-

tacle.

Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/

Ground Circuit

DRY2022N_SVG

1. L1

2. Earth/Ground

3. Neutral Side

4. Round Earth/Ground Prong

5. Neutral

6. 0 V.A.C.

7. 120 ± 12 V.A.C.

8. 120 ± 12 V.A.C.

Figure 13

WARNING

To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to connect

the washer to the electric power source.

W082

Earth/Ground Instructions

This appliance must be properly connected to protective earth/

ground. In the event of malfunction or breakdown, the earth/

ground will reduce the risk of electric shock by providing a path

of least resistance for electric current.

The appliance is equipped with a cord having an equipment earth/

ground conductor and a three-prong earth/ground plug. The plug

must be plugged into an appropriate outlet that is properly instal-

Installation

DO NOT COPY or TRANSMIT

10 Part No. 804650ENR2

Andere Handbücher für AFNE9BSP113TN01

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems F232136R5 Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems F232157R7 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SFNBXFSP122DW01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems POCKET HARDMOUNT UW50P4 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWB19A*-1109 series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TLW12C_SVG Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems HD60 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems PHM1397C Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems HX Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HWTB21 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F8437801 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems W446I Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems HC18SN2 Handbuch

Alliance Laundry Systems

Alliance Laundry Systems FTS80A*H Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems EA2011 Series Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems HC125BYV Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems CS2000 Stücklistenhandbuch

Alliance Laundry Systems

Alliance Laundry Systems LWK23A*-3050 series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HCD020GD2 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DWA021*A Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems F8354001 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems H011C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems NetMaser Series Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 802715 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung