Alliance Laundry Systems AWN43RSN115CW01 Betriebsanleitung

Troubleshooting

Home Topload Washers

Refer to Page 7 for Model Numbers

TLW24C_SVG2

Original Instructions

Keep These Instructions for Future Reference.

CAUTION: Read the instructions before using the machine.

(If this machine changes ownership, this manual must accompany machine.)

www.alliancelaundry.com Part No. 204666ENR2

July 2020

https://appliancetechmanuals.com

Table of Contents

Safety Information..................................................................................5

Locating an Authorized Service Person.............................................................6

Introduction........................................................................................... 7

Model Identification........................................................................................7

How Your Washer Works.................................................................................7

Customer Service............................................................................................9

Serial Plate Location....................................................................................... 9

Troubleshooting Diagnostics................................................................. 10

Factory Test Procedure.................................................................................. 10

To Enter Factory Test Procedure................................................................. 10

To Exit Factory Test Procedure................................................................... 10

Advance to Drain and Spin............................................................................ 13

Feature Configuration - Through Serial Nos. Beginning 1810........................... 14

Dipswitch Configuration............................................................................ 14

Feature Configuration - Starting Serial Nos. beginning 1810.............................14

Audio Signals........................................................................................... 14

Rapid Advance..........................................................................................14

Mixing Valve Solenoid Test........................................................................... 14

WASH and RINSE LEDs Flash After Installing New Control........................... 15

Error Codes..........................................................................................16

Troubleshooting Flowcharts..................................................................20

No Hot Water............................................................................................... 21

No Cold Water..............................................................................................22

No Warm Water............................................................................................ 23

Slow Hot Fill or Warm Fill is Too Cold...........................................................24

Water Fill Does Not Stop At Proper Level.......................................................25

Pressure Sensor Error.................................................................................... 26

Slow Spin Or No Spin................................................................................... 27

Washer Is Locked Up Or Binding................................................................... 28

Outer Tub Does Not Empty............................................................................29

Excessive Vibration.......................................................................................30

Water Leaking From Outer Tub......................................................................31

Lid Does Not Lock........................................................................................32

Adjustments......................................................................................... 33

written consent of the publisher.

DO NOT COPY or TRANSMIT

3 Part No. 204666ENR2

https://appliancetechmanuals.com

Leveling Legs...............................................................................................33

Belt............................................................................................................. 33

Drive Bell Torque......................................................................................... 33

Cycle Sequence Charts..........................................................................34

Normal Eco Cycle.........................................................................................34

Non-Eco Cycles............................................................................................34

Cycle Values.................................................................................................35

Agitation Levels........................................................................................... 36

Keys............................................................................................................ 36

DO NOT COPY or TRANSMIT

4 Part No. 204666ENR2

https://appliancetechmanuals.com

Safety Information

Precautionary statements (“DANGER,” “WARNING,” and

“CAUTION”), followed by specific instructions, are found in this

manual and on machine decals. These precautions are intended

for the personal safety of the operator, user, servicer, and those

maintaining the machine.

DANGER

Indicates an imminently hazardous situation that, if

not avoided, will cause severe personal injury or

death.

WARNING

Indicates a hazardous situation that, if not avoided,

could cause severe personal injury or death.

CAUTION

Indicates a hazardous situation that, if not avoided,

may cause minor or moderate personal injury or

property damage.

Additional precautionary statements (“IMPORTANT” and

“NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to in-

form the reader of specific procedures where minor

machine damage will occur if the procedure is not fol-

lowed.

NOTE: The word “NOTE” is used to communicate in-

stallation, operation, maintenance or servicing informa-

tion that is important but not hazard related.

In the interest of safety, some general precautions relating to the

operation of this machine follow.

WARNING

• Failure to install, maintain and/or operate this

product according to the manufacturer’s instruc-

tions may result in conditions which can produce

serious injury, death and/or property damage.

• Do not repair or replace any part of the product or

attempt any servicing unless specifically recom-

mended or published in this Service Manual and

unless you understand and have the skills to car-

ry out the servicing.

• Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to

ensure that the product is properly grounded and

to reduce the risk of fire, electric shock, serious

injury or death.

W006R2

WARNING

To reduce the risk of electric shock, fire, explosion,

serious injury or death:

• Disconnect electric power to the washer before

servicing.

• Never start the washer with any guards/panels re-

moved.

• Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to

ensure that the washer is properly grounded.

W003

WARNING

Repairs that are made to your products by unquali-

fied persons can result in hazards due to improper

assembly or adjustments subjecting you, or the inex-

perienced person making such repairs, to the risk of

serious injury, electrical shock, or death.

W007

Safety Information

DO NOT COPY or TRANSMIT

5 Part No. 204666ENR2

https://appliancetechmanuals.com

CAUTION

If you or an unqualified person perform service on

your product, you must assume the responsibility

for any personal injury or property damage which

may result. The manufacturer will not be responsible

for any injury or property damage arising from im-

proper service and/or service procedures.

W008

NOTE: The WARNINGS and IMPORTANT INSTRUC-

TIONS appearing in this manual are not meant to cover

all possible conditions and situations that may occur.

Common sense, caution and care must be exercised

when installing, maintaining or operating the machine.

Always contact your dealer, distributor, service agent or the man-

ufacturer about any problems or conditions you do not under-

stand.

Locating an Authorized Service Person

Alliance Laundry Systems is not responsible for personal injury

or property damage resulting from improper service. Review all

service information before beginning repairs.

Warranty service must be performed by an authorized technician,

using authorized factory parts. If service is required after the war-

ranty expires, Alliance Laundry Systems also recommends con-

tacting an authorized technician and using authorized factory

parts.

Safety Information

DO NOT COPY or TRANSMIT

6 Part No. 204666ENR2

https://appliancetechmanuals.com

Introduction

Model Identification

Information in this manual is applicable to these washer models:

AWN43RSN115CW01 AWN63RSN115CW14

AWN43RSN115CW14 AWN63RSN115TW01

AWN43RSN115TW01 AWN63RSN115TW0P

AWN43RSN116TW01 AWN63RSN116TW01

AWN43RSN305LW01 ZWN43RSN115CW01

AWN43RSN305NW29 ZWN43RSN116CW01

AWN43RSN305XW01 ZWN63RSN115CW01

AWN63RSN115CW01 ZWN63RSN116CW01

Introduction

DO NOT COPY or TRANSMIT

7 Part No. 204666ENR2

https://appliancetechmanuals.com

How Your Washer Works

1. Electronic Control (inside control hood)

2. Agitator

3. Outer Tub

4. Pump

5. Motor

6. Drive Board

7. Drive Shaft

8. Washtub

9. Mixing Valve

Figure 1

The cycle begins with a wash fill. The water temperature is deter-

mined by the temperature selected on the control. While water

fills the washtub, a column of air is trapped in a pressure bulb and

hose. The air pressure continues to increase as the washtub fills

Introduction

DO NOT COPY or TRANSMIT

8 Part No. 204666ENR2

https://appliancetechmanuals.com

with water until the air pressure hose reaches a level determined

by the selected water level (load size switch setting) and the se-

lected cycle. The water will stop filling at the minimum level for

the selected cycle when Auto Fill is selected. In either case, the

washer will begin load sensing to determine if more water is re-

quired for the actual load in the washer and the cycle selected.

The wash agitation segment of the cycle begins at this time and

the lid must be closed and locked for any further washer opera-

tion. On non-Eco cycles, after approximately two minutes of

wash, the washer repeats the load sensing process to confirm that

the water level is still correct for the load and cycle selected.

The washer uses a reversing type of inverter drive motor and a

special stretch drive belt.

During agitation, the motor alternates between the clockwise and

counterclockwise direction. The rapid reversal from one direction

to the other creates the wash action. The stretch belt needs no ad-

justment for belt tension. Proper belt tension is provided by the

pulley spacing and use of the proper size stretch belt. This elimi-

nates belt slippage and ensures an efficient wash action.

After the wash agitation is complete and a short pause occurs, the

control advances into the wash spin. During spin, the washtub

will first rotate at 20 RPM while the electric pump runs to drain

the water from the tub. Once the pressure sensor recognizes that

the tub has been drained, the RPM will increase to extract water

from the load and the pump will continue running to remove the

water.

Water is introduced during the wash spin to spray the garments

and remove suds from them. The wash spin is followed by a rinse

step to rinse away any detergent residue.

During the rinse step in the Normal Eco cycle there will be two

more spray rinses. Water is sprayed into the washtub while it is

spinning. In all other cycles, the washer fills and then agitates

like the wash portion of the cycle.

Following the rinse step a final spin extracts the rinse water from

the clothes preparing them for the dryer. This will also start at 20

RPM with the pump running. After draining the spin will then in-

crease to a higher speed that varies depending on what cycle has

been selected. After the machine has been in spin long enough to

ensure that most of the water has been removed from the load,

the pump will run intermittently for the rest of the spin in order to

improve drain performance and reduce noise.

Refer to Cycle Sequence Charts section for a detailed breakdown

of each cycle.

Customer Service

If literature or replacement parts are required, contact the source

from whom the machine was purchased or contact Alliance

Laundry Systems at (920) 748-3950 for the name and address of

the nearest authorized parts distributor.

For technical assistance, call (920) 748-3121.

Serial Plate Location

When calling or writing about your product, be sure to mention

model and serial numbers. Model and serial numbers are located

on Serial Plate as shown.

TLW1851P_SVG

1. Serial Plate

Figure 2

Introduction

DO NOT COPY or TRANSMIT

9 Part No. 204666ENR2

https://appliancetechmanuals.com

Troubleshooting Diagnostics

Factory Test Procedure

It is helpful to run the Factory Test Procedure first to diagnose the

machine’s issue. This procedure tests all machine features and

operations.

To Enter Factory Test Procedure

1. Disconnect electrical power from unit.

2. Reconnect electrical power to unit.

3. Wait about 10 seconds.

4. Turn Cycle Selection knob to opposite of Normal Eco. Stay

on that selection for at least one second.

5. Press and hold the Start/Pause button.

6. Change Cycle Selection knob to Normal Eco within 5 seconds

or Start press will be invalid.

7. Stay on Normal Eco for at least one second. Control will enter

Factory Test Mode.

8. To advance through the sequence of test steps press the Start/

Pause button. Refer to Table 1 for all tests in the Factory Test

Procedure.

To Exit Factory Test Procedure

To exit the Factory Test Procedure, refer to Exit column in Table

1 and Exit Key in Table 2.

Factory Test Procedure Quick Reference Chart

Number

Display

(LEDs lit) Motor Valves Lid Pump Exit Step

0 All LEDs lit Off None Unlocked Off 1 Show Mode

1 Refer to Cycle

Switch Test

Off None Unlocked Off 3 and then 1 Cycle Switch

2 Refer to Tem-

perature

Switch Test

Off None Unlocked Off 3 and then 1 Temperature

Switch

3 Refer to Load

Size Switch

Test

Off None Unlocked Off 3 and then 1 Load Size

Switch

4 Refer to Extra

Rinse Test

Off None Unlocked Off 3 and then 1 Extra Rinse

5 Refer to Lid

Switch Test

Off None Unlocked Off 10 and then 1 Lid Switch

6 Wash Off Hot Unlocked Off 1 Hot Fill

7 Rinse Off Cold Unlocked Off 1 Cold Fill

8 Wash, Rinse Off Hot, Cold Unlocked Off 2 and then 1 Pressure Sen-

sor Fill

9 Lid Lock Off None Locked Off 7 and then 1 Lid Lock

Check

Table 1 continues...

Troubleshooting Diagnostics

DO NOT COPY or TRANSMIT

10 Part No. 204666ENR2

https://appliancetechmanuals.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen FF7008WN Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HX Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 802756R3 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Cabinet Hardmount Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems WF150 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWS02M series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LTS87A*H Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems AFNE9BSS Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FLW700C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWS02N Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CCN020HNF Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 800138R2 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Hardmount Coin and OPL Installations- und Betriebshandbuch

Alliance Laundry Systems

Alliance Laundry Systems LWN432SP113TW04 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HC18MC2 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SF18VNV Wartungs- und Serviceanleitung

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen LFNE5B Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems AWN311SP111TW01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWK73AW-3050 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems A Series Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HWTB21 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HF18VCV Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Home Laundry Automatic Washer Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung