Allied Telesis SB244-03 Bedienungsanleitung

Simply connecting the world

Patch Release Note

Patch SB244-03

For SwitchBlade 4000 Series Switches and

AT-9800 Series Switches

Introduction

This patch release note lists the issues addressed and enhancements made in

patch SB244-03 for Software Release 2.4.4 on existing models of SwitchBlade

4000 Series Switches and AT-9800 Series Switches. Patch file details are listed in

Table 1.

This release note should be read in conjunction with the following documents:

■SwitchBlade Documentation Set for Software Release 2.4.3 (Document

Number C613-03042-00 Rev E) and Release Note for Software Release 2.4.4

for SwitchBlade 4000 Switches and AT-9800 Series Switches (Document

Number C613-10342-00 Rev A) available on the Documentation and Tools

CD-ROM packaged with your switch, or from www.alliedtelesyn.co.nz/

documentation/documentation.html.

■AT9800 Series Switches Documentation Set for Software Release 2.4.3

(Document Number C613-03044-00 Rev B) and Release Note for Software

Release 2.4.4 for SwitchBlade 4000 Switches and AT-9800 Series Switches

(Document Number C613-10342-00 Rev A) available on the

Documentation and Tools CD-ROM packaged with your switch, or from

www.alliedtelesyn.co.nz/documentation/documentation.html.

WARNING: Using a patch for a different model or software release may cause

unpredictable results, including disruption to the network. Information in this

release note is subject to change without notice and does not represent a

commitment on the part of Allied Telesyn International. While every effort has

been made to ensure that the information contained within this document and

the features and changes described are accurate, Allied Telesyn International

can not accept any type of liability for errors in, or omissions arising from the

use of this information.

Table 1: Patch file details for Patch SB244-03.

Base Software Release File sb-244.rez

Patch Release Date 26-Nov-2002

Compressed Patch File Name sb244-03.paz

Compressed Patch File Size 250571 bytes

2Patch Release Note

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

Features in SB244-03

Patch SB244-03 includes all issues resolved and enhancements released in

previous patches for Software Release 2.4.4, and the following enhancements:

MLD snooping is now supported on AT-9800 Series Switches and Rapier i

Series Switches.

The following issues have been resolved:

• PIM was disabled when the RESET IP command was executed.

• PIM reverse path check was not working correctly.

• PIM_DM assert was not working correctly.

• DVMRP messages were not being flooded correctly.

• Executing the SHOW PPP command sometimes caused a fatal error.

• IP forwarding was not working correctly on SwitchBlade 4000 Series

Switches.

• Changes have been made for supporting non-contiguous IP

subnetworks.

The counter for transmitted ARP packets was incorrect. This issue has been

resolved.

On SwitchBlade 4000 Series Switches, the MIB browser could not see the

slave controller card. This issue has been resolved.

When SwitchBlade 4000 Series Switches were operating with a full set of

line cards, and the test module was enabled for all interfaces, an excessive

amount of traffic was generated. This issue has been resolved.

VLAN number 4077 could not be created. This issue has been resolved.

When there were 4000 VLANs, executing the DESTROY VLAN=ALL

command caused a fatal error. This issue has been resolved.

The ADD IPV6 ND command was not displayed by the SHOW

CONFIGURATION DYNAMIC command. This issue has been resolved.

The ARP cache is now updated when a gratuitous ARP request or reply

packet is received.

PCR: 02414 Module: IPV6, SWI, IPG, VLAN Network affecting: No

PCR: 02451 Module: IPG, PIM, VLAN, SWI Network affecting: No

PCR: 02471 Module: IPG Network affecting: No

PCR: 02480 Module: SWI Network affecting: No

PCR: 02483 Module: SWI, TM Network affecting: No

PCR: 02486 Module: SWI Network affecting: No

PCR: 02487 Module: SWI Network affecting: No

PCR: 02490 Module: IPv6 Network affecting: No

PCR: 02491 Module: IPG Network affecting: No

Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 3

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

288MB RDRAM was initialised incorrectly, resulting in unpredictable

behaviour. This issue has been resolved.

Inuse DHCP entries (that are displayed in the SHOW DHCP CLIENT

command) will now expire and be reclaimed.

It was possible to add the same IPv6 prefix to different IPv6 interfaces. This

issue has been resolved.

The wrong error message was displayed if PPP compression over L2TP was

attempted. The correct message is now generated, stating that the CREATE

PPP command is invalid.

Some parameters in the SET IP IGMP command had incorrect ranges. This

issue has been resolved. The correct ranges are:

SET IP IGMP [LMQI=1..255] [LMQC=1..5]

[QUERYINTERVAL=1..65535] [QUERYRESPONSEINTERVAL=1..255]

[ROBUSTNESS=1..5] [TIMEOUT=1..65535]

If multiple IPv6 interfaces shared the same link-local address, pings to the

link-local address sometimes failed. This issue has been resolved.

Loading files to NVS caused a fatal error. This issue has been resolved.

A warning was not given if the egress limit for a port was not set to a

multiple of 64. This issue has been resolved.

ARP entries on the SwitchBlade 4000 Series Switch controller card are now

updated correctly if a device changes to a different line card.

The source net mask has been removed from DVMRP prune, graft and

graft-ack messages.

Executing the PING command sometimes caused a memory leak. This issue

has been resolved.

Untagged IGMP packets were erroneously sent out of tagged ports. This

issue has been resolved.

PCR: 02492 Module: SWI Network affecting: No

PCR: 02493 Module: DHCP Network affecting: No

PCR: 02494 Module: IPv6 Network affecting: No

PCR: 02497 Module: PPP Network affecting: No

PCR: 02499 Module: IPG Network affecting: No

PCR: 02502 Module: Ping, IPv6 Network affecting: No

PCR: 02503 Module: NVS Network affecting: No

PCR: 02504 Module: SWI Network affecting: No

PCR: 02507 Module: SWI Network affecting: No

PCR: 02509 Module: DVMRP Network affecting: No

PCR: 02511 Module: Ping Network affecting: No

PCR: 02516 Module: IPG Network affecting: No

4Patch Release Note

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

Features in SB244-02

Patch file details are listed in Table 2:

Patch SB244-02 includes all issues resolved and enhancements released in

previous patches for Software Release 2.4.4, and the following enhancements:

Some parameters in MLD specific query messages were not working

correctly. This issue has been resolved.

The ENABLE IPV6 MTUDISCOVERY and SET IPV6 MTU INTERFACE

commands were not displayed in the SHOW CONFIGURATION

DYNAMIC command. This issue has been resolved.

DHCP entry reclaim checks are now delayed by 10 seconds if the entry is

unroutable because the interface is not up.

Link-local address behaviour was incorrect. Also, the PUBLISH parameter

was not updated by the SET IPV6 INTERFACE command, or displayed in

the SHOW IPV6 INTERFACE command. These issues have been resolved.

Large local packets were not being fragmented. Also, the More Fragment

flag in the IPv6 fragment header was not being set correctly. These issues

have been resolved.

Received Router Advertisements (RAs) were discarded when the interface

was enabled to send RAs. This issue has been resolved.

The status page in the GUI was not displaying correctly. This issue has been

resolved.

The SLVPASSWORD string in the ENABLE SYSTEM SYSR SLVFEATURE

and ENABLE SYSTEM SYSR SLVRELEASE commands was not copying

correctly. This issue has been resolved.

Table 2: Patch file details for Patch SB244-02.

Base Software Release File sb-244.rez

Patch Release Date 1-Nov-2002

Compressed Patch File Name sb244-02.paz

Compressed Patch File Size 57728 bytes

PCR: 02406 Module: IPV6 Network affecting: No

PCR: 02426 Module: IPV6 Network affecting: No

PCR: 02427 Module: DHCP Network affecting: No

PCR: 02428 Module: IPV6 Network affecting: No

PCR: 02450 Module: IPV6 Network affecting: No

PCR: 02452 Module: IPV6 Network affecting: No

PCR: 02458 Module: SWI, GUI Network affecting: No

PCR: 02459 Module: CORE Network affecting: No

Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 5

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

Sometimes a port reported an interface as being down, but the port counters

kept incrementing. This issue has been resolved.

The CREATE TRIGGER MODULE=SWITCH command now recognises

ports in x.y notation when specifying the PORT parameter.

A fatal error occurred on SwitchBlade 4000 Series Switches when booting

from a script that added ports to a trunk group that was hot swapped out.

This issue has been resolved.

Support for multi-homed interfaces has been added.

The board descriptions have changed for some instances of AT-9800 Series

Switches.

When a Telnet session was closed, SWITCH debug was not disabled if it had

been enabled for the Telnet session. This issue has been resolved.

After an ASYN port test, the port is now reset to its pre-test state if the test

was started by a user connected to the same ASYN port.

The Built-in Self Test failed on SwitchBlade chassis. This issue has been

resolved.

The configuration was not restored correctly after a line card was hot

swapped out. This issue has been resolved.

A string compare error was occurring in the conditional statement of the

script. This issue has been resolved.

PCR: 02460 Module: SWI Network affecting: No

PCR: 02461 Module: SWI Network affecting: No

PCR: 02462 Module: SWI Network affecting: No

PCR: 02463 Module: DVMRP, IPG Network affecting: No

PCR: 02467 Module: CORE Network affecting: No

PCR: 02468 Module: SWI Network affecting: No

PCR: 02469 Module: TM Network affecting: No

PCR: 02470 Module: SWI Network affecting: No

PCR: 02476 Module: VRRP, CORE Network affecting: No

PCR: 02478 Module: SCRIPT Network affecting: No

6Patch Release Note

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

Features in SB244-01

Patch file details are listed in Table 3:

Patch SB244-01 includes the following enhancements:

When an interface went down (or was disabled) on an AS border router, the

external routes were not removed from the routing domain. Such routes are

now removed by premature aging.

The learning unit was locking under heavy load. This could result in pings

to a network device failing, and over an hour all dynamic MAC addresses

could be lost. Sometimes a large number of pause frames were generated by

the system. This issue has been resolved.

When an IP Multihomed interface was used as an OSPF interface,

neighbour relationships were only established if the IP interface for OSPF

was added first in the configuration. Now, OSPF establishes neighbour

relationships regardless of the IP Multihomed interface configuration order.

The SwitchBlade mirror port field on the second instance of a switch chip

was displaying as though it was the first instance. This issue has been

resolved.

The following issues have been resolved:

• IP route updating was not working correctly

• IGMP snooping behaviour was incorrect

• The SHOW DVMRP FORWARDING command displayed incorrect

port numbers.

DHCP RENEW request messages are now unicast (as defined in the RFC),

not broadcast.

After a prune lifetime had expired, the interface was not joined back to the

DVMRP multicast delivery tree. This issue has been resolved.

Table 3: Patch file details for Patch SB244-01.

Base Software Release File sb-244.rez

Patch Release Date 23-Oct-2002

Compressed Patch File Name sb244-01.paz

Compressed Patch File Size 84666 bytes

PCR: 01285 Module: OSPF Network affecting: No

PCR: 02353 Module: SWI Network affecting: No

PCR: 02359 Module: IPG Network affecting: No

PCR: 02361 Module: SWI Network affecting: No

PCR: 02394 Module: IPG, SWI, DVMRP Network affecting: No

PCR: 02396 Module: DHCP Network affecting: No

PCR: 02397 Module: DVMRP Network affecting: No

Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 7

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

The following issues have been resolved:

• It was possible to assign the same network on different IPV6 interfaces

• The loopback address was being added to other interfaces

• The tunnel configuration was not showing correctly in IPV6

configuration commands

• RIPv6 now sets the metric of routes for interfaces that are DOWN to 16,

and immediately sends responses when the link status of VLAN

interfaces changes.

Neighbour discovery and PIM6 caused a fatal error when IPv6 was not

enabled, or when the IPv6 feature license was not present. This issue has

been resolved.

A Router-Alert option has been added. Also, the SHOW IPV6 MLD

INTERFACE command now works correctly.

ICMP was sending too many messages back as responses to fragmented

packets. This issue has been resolved.

A warning now appears when the DELETE IP INTERFACE command is

executed before the DELETE DVMRP INTERFACE command.

VRRP pre-empt mode was not working with advertisement updates of 1

second or more because this did not allow for interface start time on startup.

Now a check is made to verify that interfaces are UP before timers are

started.

Static IP ARP entries could not be added to hardware at boot time. Also, an

IPX circuit could not be deleted from hardware. These issues have been

resolved.

Multicasting forwarding was not working correctly. This issue has been

resolved.

The IGMP port list was not updating correctly when a port went down. This

issue has been resolved.

ICMPv6 was returning an error for non-zero fragment offsets. This issue has

been resolved.

PCR: 02398 Module: IPV6 Network affecting: No

PCR: 02401 Module: IPV6 Network affecting: No

PCR: 02406 Module: IPV6 Network affecting: No

PCR: 02407 Module: IPG Network affecting: No

PCR: 02409 Module: IPG Network affecting: No

PCR: 02410 Module: VRRP Network affecting: No

PCR: 02413 Module: IPG, IPX2 Network affecting: No

PCR: 02416 Module: DVMRP, IPG Network affecting: No

PCR: 02417 Module: VLAN, IPG Network affecting: No

PCR: 02418 Module: IPV6 Network affecting: No

8Patch Release Note

Patch SB244-03 for Software Release 2.4.4

C613-10349-00 REV C

Packets with a RIP source address and next hop address that are not on the

same subnet as the interface will now be processed. If the received next hop

is not on the same subnet, it is treated as 0.0.0.0.

On GBICs, the link was forced up when the transmit fibre was removed.

Once up, the link could not be taken down again by removing the transmit

fibre. This issue has been resolved.

IGMP messages sometimes caused a fatal error. This issue has been

resolved.

Multicast downstream groups are now added and deleted correctly.

Errata

AT-9800 Series Switches do not have Ethernet interfaces (for example, eth0).

Previously released documentation incorrectly states that these interface types

are valid. AT-9800 switch ports are Ethernet ports, and these are referenced in

commands with the PORT parameter.

IPSec and ISAKMP are not available on the 2.4.4 release for SwitchBlade 4000

Series Switches and AT-9800 Series Switches.

Availability

Patches can be downloaded from the Software Updates area of the Allied

Telesyn web site at www.alliedtelesyn.co.nz/support/updates/patches.html. A

licence or password is not required to use a patch.

PCR: 02415 Module: IPG Network affecting: No

PCR: 02420 Module: SWI Network affecting: No

PCR: 02423 Module: SWI Network affecting: No

PCR: 02425 Module: IPG Network affecting: No

Andere Allied Telesis Schalten Handbücher

Allied Telesis

Allied Telesis x900-48FE Anwendungshandbuch

Allied Telesis

Allied Telesis AT-GS950/8 Bedienungsanleitung

Allied Telesis

Allied Telesis AT-GS903SX Bedienungsanleitung

Allied Telesis

Allied Telesis x330 Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-8624T/2M Handbuch

Allied Telesis

Allied Telesis WebSmart AT-FS750/48 Bedienungsanleitung

Allied Telesis

Allied Telesis AT-GS950/24 Bedienungsanleitung

Allied Telesis

Allied Telesis x330 Series Bedienungsanleitung

Allied Telesis

Allied Telesis Rapier 48w Bedienungsanleitung

Allied Telesis

Allied Telesis GS910 Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-IX5-28GPX Bedienungsanleitung

Allied Telesis

Allied Telesis SwitchBlade x908 GEN2 Bedienungsanleitung

Allied Telesis

Allied Telesis AT-x230-10GP Bedienungsanleitung

Allied Telesis

Allied Telesis AT-FS713FC/xx Bedienungsanleitung

Allied Telesis

Allied Telesis AT-8800 Series Bedienungsanleitung

Allied Telesis

Allied Telesis x900-12X Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-8000S/24POE Bedienungsanleitung

Allied Telesis

Allied Telesis AT-8000S/48 Bedienungsanleitung

Allied Telesis

Allied Telesis Layer 3 Switches Montage- und Wartungsanleitung

Allied Telesis

Allied Telesis AT FS708LE AT-FS708LE AT-FS708LE Bedienungsanleitung

Allied Telesis

Allied Telesis AT-x930-28GTX Bedienungsanleitung

Allied Telesis

Allied Telesis AT-FS201 Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-GS900M Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-GS900/16 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung