AllwinTech OneInGate 111 Bedienungsanleitung

OneInGate 111 VoIP Router

Quick Install Guide

Version: 0.9.6(draft)

Document number: QIG-OneIn120-0.96

Date Issued by 09/21/2004

Table of contents

Chapter 1 Introducing OneInGate 120 VoIP Router.......................................................................3

1.1 Key Features .......................................................................................................................3

1.2 Specifications .....................................................................................................................3

Chapter 2 Getting Started................................................................................................................5

2.1 Identifying External Components................................................................................... 5

2.2 Installation.........................................................................................................................6

Chapter 3 Configuration ..............................................................................................................7

3.1 Connection ......................................................................................................................... 8

3.2 System status................................................................................................................... 10

3.3 VoIP Call Out................................................................................................................... 11

Chapter 4 VoIP Router Setting .................................................................................................. 13

4.1 VPN point-to-point VoIP phone environment setting ..............................................13

4.2 Installation plan........................................................................................................ 13

4.3 VPN Point-to-point VoIP phone construction.......................................................... 14

On net call: .......................................................................................................................14

4.4 Setting Procedure .....................................................................................................15

Chapter 1 Introducing OneInGate 120 VoIP Router

1.1 Key Features

VoIP

zSupport 2 simultaneous VoIP calls

zSupport T.38 FAX relay

zSupport QoS for VoIP

zCompliant with H.323 standard

zBuild in Web call Server function

zExtensible by external IVR/CDR/Billing servers for value- added application

zSupport Alternate gatekeepers

zSupport worldwide off net call by ITSP service

zSupport Multiple dialing plan / Call hunting group

zAdaptive Jitter Buffer function

zMultiple call profile for adjust VAD, Audio CODEC, H.245

tunneling, DTMF In/Out band, FAX relay, Frame Size, Q.931

Fast start parameters

Router

zSupport static and dynamic IP from DHCP, PPPoE

zBuilt-in DHCP Server

zSupport TCP/UDP Port Mapping (Local Server Mapping)

zSupport User-definable Static Routing Table

zSupport Network Access Rules (LAN-to-WAN & WAN-to-LAN)

zSelf-Protection against DoS Attacks

zDynamic DNS Support

1.2 Specifications

zPhysical: 214 X 147 X 32 mm

zPower: 12V DC, 1A(Max.) Adaptor

zWeight: 450 g

zWAN: 10/100Mbps RJ-45 connector, auto-sensing

zLAN: 4-port 10/100Mbps Ethernet Switch. (Auto MDI-II/MDI-X)

zVoIP: 2 SLIC(FXS) connect to phone sets

zLED Indicators : Power, Status, WAN linking , 4X LAN linking, Phone 1, phone 2

zSupported Protocol: UDP, TCP, Standard H.323, NAT,BOOTP, TFTP, FTP, HTTP, TELNET,

IEEE 802.3/ IEEE 802.3u

zSelectable Coders: G.711, G.723.1, G.726, G.729A

zDTMF / Call progress tone detection and generation

zG.168 echo cancellation

z1 Reset button for load factory default IP parameters setting

zUser friendly Web configure interface

zConfiguration/Upgrade by FTP and Web

zBuild-in watching dog for auto recovery

Chapter 2 Getting Started

2.1 Identifying External Components

Front Panel

Message: Flash light means GW booting OK

Ready: Constant light means VOIP service OK

Line: The PSTN line is in use.

VOIP: The VoIP line is in use

Status: The server registers status

Rear Panel

(Figure2-2)

12V: For the included power adapter. Be sure to use only the 12VDC power adapter included

with the product. Using the wrong power adapter can damage the product and void the

warranty.

Phone: Normal RJ-11 phone jacks used to connect analog telephones and fax machines.

Line: Normal RJ-11 phone jacks used to connect analog phone line or landline.

Reset: Clear all settings and restore them to the initial values present when the device was

purchased. After performing the reset, make sure to redefine the IP settings for the device in

the ‘Connection’.

LAN 1~3: A 10/100 dual-speed Ethernet port fitted with an RJ-45 connector used to connect

the VoIP gateway to a LAN device.

WAN : A 10/100 dual-speed Ethernet port fitted with an RJ-45 connector used to connect the

VoIP gateway to WAN device (usually a router).

2.2 Installation

Do not place heavy objects on the Router. Placing the Router in a well ventilated area is very

important. Not doing so may cause damage to the unit.

(Figure2-3)

Chapter 3 Configuration

The default setting of DHCP Server inside OneInGate120 VoIP Router is turn ON, So please set up

your PC TCP/IP network as “Get IP Automatically” from DHCP to get internal IP from

OneInGate120. By default, The OneInGate120 will become the network gateway and default IP is

192.168.1.1 and will assign your PC IP as 192.168.1.X.

Please go to “Control Panel” ”Network”. In the “Configure” page, choose the TCP/IP→of LAN card,

and press “Properties” please choose “Obtain IP Address Automatically”

Launch your browser and open the OneInGate120 Internal UI WAP page as

http://192.168.22.1/admin.

(Figure3-1)

The default User name is voip

The default Password is 1234

3.1 Connection

Click “Connection” option below “System Setup” item:

( Figure3-2)

Please select the type of Internet connection you have and set up the router to use the IP

Address Automatically, Static-IP or PPPoE ADSL connection.

If your ISP has not given you an IP address, select Obtain an IP Address Automatically

(default). If you have been given a specific IP address, select Specify an IP Address.

(Figure3-3)

To use Static-IP ADSL connection, please select “Specify an IP Address” and enter WAN IP

settings, including the Primary and Secondary DNS IPs, supplied by your ISP.

(Figure3-4)

To use PPPoE ADSL connection, please select Yes in use “PPPoE” ADSL service and

enter the “username” and “password” in the PPPoE setup section. Most of ADSL ISPs

assign dynamic-IP settings to the router when using PPPoE. Please select Obtain IP Address

Automatically(default setting). You can leave the Primary and Secondary DNS IP settings in

default. The router automatically obtains these settings from your ISP when the PPPoE

connection is successfully established.

(Figure3-5)

3.2 System status

“System Setup” →”System status” to check system status.

(Figure3-6)

Inhaltsverzeichnis

Andere AllwinTech Netzwerk-Router Handbücher

AllwinTech

AllwinTech H Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise