Altai Technologies A8 Bedienungsanleitung
Altai Technologies Ltd. All rights reserved
ALTAI A8
SUPER WIFI BASE STATION
INSTALLATION GUIDE
Version 1.2
Date: October, 2013
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
Copyright © 2007 Altai Technologies Limited
ALL RIGHTS RESERVED.
Altai Technologies Limited
Unit 209, 2/F,
East Wing, Building 17,
Hong Kong Science Park,
Shatin, New Territories,
Hong Kong
Telephone: +852 3758 6000
Fax: +852 2607 4021
Web: www.altaitechnologies.com
Customer Support Centre:
Email: supp[email protected]
Radio Frequency Interference Requirements
This device complies with Part 15 of FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
3. This device should not be co-located or operating in conjunction with any
other antenna or transmitter.
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
This equipment generates uses and can radiate radio frequency energy. If it is not
installed and used in accordance with the instructions, harmful interference to radio
communications may be caused.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance,(example –use only shielded
interface cables when connecting to computer or peripheral devices) any changes
or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Warning
The user is advised to keep away from the base-station and antenna with at least
45cm when the base-station is in operation.
Please install a lightning arrestor to protect the base station from lightning dissipation
during rainstorms. Lightning arrestors are mounted outside the structure and must be
grounded by means of a ground wire to the nearest ground rod or item that is
grounded.
Disclaimer
All specifications are subject to changes without prior notice. Altai Technologies
assumes no responsibilities for any inaccuracies in this document or for any obligation
to update information in this document. This document is provided for information
purposes only. Altai Technologies reserves the right to change, modify, transfer, or
otherwise revise this publication without notice.
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
Contents
1. Introduction ............................................................................................................................5
2. A8 Base Station Outlook.......................................................................................................5
3. A8 Antenna Outlook .............................................................................................................6
4. A8 Base Station Package ....................................................................................................7
5. A8 Antenna Package...........................................................................................................7
6. Site Preparation......................................................................................................................9
7. Mounting A8 antenna on a pole .......................................................................................9
8. Mounting 5GHz Radio Antenna........................................................................................11
9. Mounting A8 Base Station on the Pole............................................................................12
10. Mounting A8 Base Station on the Wall ........................................................................12
11. Connecting RF Cables ...................................................................................................13
12. Weatherproofing the RF Connectors ..........................................................................15
12.1. Introduction ..........................................................................................................15
12.2. Installation Tips......................................................................................................16
12.3. Preparing A8 BTS RF Ports ...................................................................................17
12.4. Connecting RF Cables ...........................................................................................18
12.5. RF Cable-to-A8 BTS Connection .......................................................................18
12.6. RF Cable-to-Antenna Connection...................................................................20
13. Recommendation on RF cable and Antenna Pole .................................................21
13.1. RF Cable ................................................................................................................21
13.2. Antenna Pole Height and Size ..........................................................................22
14. Grounding Protection.....................................................................................................22
15. Typical Site Setup.............................................................................................................23
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
1. Introduction
This guide is designed to provide the information needed to mount A8 base station
(BTS) and A8 antennas at the site location.
The document is applicable for hardware platform A8 R3and the following models.
Product name: A8 Super WiFi Base Station
Model number: WA8011A-A
It is assumed in this document that a site survey has been performed before the site
installation. The appropriate antenna pole and BTS locations have been selected. It is
a good practice to have a document consists of a map and drawing illustrating the
base station and poles locations, antenna bearing/down-tilt, antenna height, etc… A
planning on IP network is also an important issue for network planning.
The user may need to refer the following document during A8 installation and
Configuration.
[1] A8 Cable Connection Guide
[2] A8 Configuration Manual
[3] A8 Super WiFi Base Station Data Sheet
2. A8 Base Station Outlook
Figure 2-1
Front
View
of
A8
Base
Station
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
Figure 2-2
Top-view of A8
3. A8 Antenna Outlook
Figure 3-1 A8 Antenna
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
4. A8 Base Station Package
A 1 x A8 base station
B 1 x metal mounting plate
C 2 x metal mounting tapes
D 4 x wall plug (left), 4 x self tapping metal screw (middle), 4 x flat washer (bottom)
1 x metal screw (right)
E A set of RJ45 connector
F Female cable connector 3+PE
Figure 4-1 A8 Base Station Package
5. A8 Antenna Package
A 1 x A8 antenna
B 1 x pole lock frame
C 2 x screw with nut
D 2 x screw
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
Figure 5-1 A8 Antenna Center-Mount Package
Note:
Parts C and Parts D are used to replace the large screw for antenna pole size
with diameter from 35mm to 80mm. Please refer to the parts 14, 15, 16, 17 in Figure 5-2.
Figure 5-2 A8 Antenna Center-Mount Assembly
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
6. Site Preparation
1. Prepare required tools, e.g. screwdriver.
2. Prepare a CAT5 (or higher) network cable for network connection of A8 base
station. Please make sure that the network connection (Ethernet Cable)
between central office and the site is properly connected.
3. Make sure that there is AC electrical power supply for A8 base station at the site.
4. Configure the A8 base station properly, e.g. assign an applicable IP address for
A8 base station.
5. Prepare 8 RF cables for RF connection (N-type connector) between antennas
and base station. Please refer to the Section 0
Figure 6-1 RF ports with water-proof rubber tape
Figure 6-2 Connecting to BTS
6. Weatherproofing the RF Connectors Wrap the RF connectors with waterproofing
kits. Please refer Section 13 Recommendation on RF cable and Antenna Pole.
7. Mounting A8 antenna on a pole
1. Mount the antenna to the pole, as shown in Figure 7-1. Mount antenna on pole.
Altai Technologies Ltd. All rights reserved
A8 Installation Guide_ R3 Hardware Platform
TPS13-010_rev1.0
2. Adjust the antenna to desired down tilt degree (0 to30 degrees), as shown in
Figure 7-2. Adjust the Down tilt Degree.
Figure 7-1 Mount antenna on pole
Figure 7-2 Adjust the Down tilt Degree
3. The antenna should look like this after it was mounted on the pole:
Inhaltsverzeichnis
Andere Altai Technologies Netzwerk-Hardware Handbücher
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
