Alu-Cab CC-A-WT-CB-KIT Bedienungsanleitung
Canopy Camper Water Tank Canvas
Bag Kit
(CC-A-WT-CB-KIT)
2
* NB - IMPORTANT NOTE
It is important to note that this Fitment Instruction must be read in conjunction with the
following Fitment Instruction:
Canopy Camper Water Tank Kit (CC-A-WT-KIT) Fitment Instruction
The above mentioned Fitment Instruction outlines the mounting of the Canopy Camper
Water Tank Kit and should be referenced up to and including sub-section 2.3.
This Fitment Instruction will form sub-sections 2.4 - 2.6, outlining the steps for
mounting the Canvas Bag Assembly.
1. Canopy Camper Water Tank Canvas Bag Kit – Tools, Fasteners &
Materials
The tables below show the equipment, i.e. tools and fasteners required to start the
Canopy Camper Water Tank Canvas Bag Kit fitment into a Canopy Camper.
Tools & Items Required:
Hardware Required: (Included with the Canopy Camper Water Tank
Canvas Bag Kit)
ITEM
DESCRIPTION
QTY
CC-A-WT-CB-KIT
CANOPY CAMPER WATER TANK CANVAS BAG KIT
1
TOOLS
2X 13MM SPANNERS
THREAD TAPE/THREAD SEALANT
13MM SOCKET AND RATCHET
DRILL
FLAT SCREW DRIVER
20MM DRILL BIT/HOLESAW
PHILLIPS SCREW DRIVER
3
Component Identification (Not to Scale)
CC-A-WT-CB-KIT:
CANOPY CAMPER WATER TANK
CANVAS BAG KIT (PREASSEMBLED)
4
2.4 Tank and Top Down Mounting Brackets
The next step to install the Canopy Camper Water Tank Kit is to fit and assemble the
Top Down Mounting Bracket assembly and place the Water Tank:
Place the Water Tank as shown
5
Place the Top Mounting Down Brackets over the Water Tank, between the Tank Ridges,
as shown.
Shift and position the Bottom, Top and Down brackets to correspond and align centrally
with the Water Tank recesses
Place 4x M8 Flat Washers on the corresponding M8 Screws as shown
Secure the Top Mounting Down Brackets at the top using 4x M8 Nyloc Nuts
6
2.5 Water Tank Canvas Bag and Breather Assembly
The next step to install the Canopy Camper Water Tank Kit is to fit the Canvas Bag
assembly and Breather assembly:
Place the Water Tank Cover Plate and Canvas Bag assembly over the corresponding
Screw fasteners as shown
7
8
Place the Water Tank Breather assembly as shown, and screw on the connector to the
Water Tank Bulk Head Fitting
9
Place M8 Flat Washers over the shown Screw fasteners
Secure the shown fasteners with the remaining M8 Nyloc Nuts
10
Fully tighten all Nyloc Nuts to secure the Water Tank in place
Inhaltsverzeichnis
Andere Alu-Cab Campingausrüstung Handbücher
Beliebte Campingausrüstung Handbücher anderer Marken
Illuminator
Illuminator 5 Bar Camp Light Kit Bedienungsanleitung
Ozark Trail
Ozark Trail WMT-8859 Bedienungsanleitung
Buck
Buck Flashpoint 770 Bedienungsanleitung
Snow Peak
Snow Peak Pack & Carry Fireplace XL Bedienungsanleitung
Asaklitt
Asaklitt 31-1171 Bedienungsanleitung
Petromax
Petromax h-mortar Bedienungsanleitung
Coleman
Coleman 5177 Series Bedienungsanleitung
Outdoor Revolution
Outdoor Revolution FUR2040 Bedienungsanleitung
Excalibur
Excalibur H800 Bedienungsanleitung
James Baroud
James Baroud Space Bedienungsanleitung
iKAMPER
iKAMPER Skycamp Series Bedienungsanleitung
Hilleberg
Hilleberg Stalon Combi Bedienungsanleitung