Alvarado SLT Gebrauchsanweisung

SLT / SLTX

WAIST HIGH SLIMLINE SECURITY TURNSTILE

INSTRUCTIONS AND

MAINTENANCE GUIDE

Revision 1.5 – September 7, 2007

Serial Number: ______________________

lvarado Manufacturing Company, Inc.

12660 Colony Street, Chino, CA 91710

(800) 423-4143 (909) 591-8431 Fax: (909) 628-1403

www.alvaradomfg.com

PUD1570

Alvarado – SLT / SLTX Turnstile

TABLE OF CONTENTS

IMPORTANT SAFETY PRECAUTIONS PAGE 3

TURNSTILE CONFIGURATION DESCRIPTIONS PAGE 4

OVERVIEW OF INSTALLATION STEPS, PAGE 5

CONCRETE SLAB REQUIREMENTS, & LAYOUT SPACING

INSTALLATION INSTRUCTIONS PAGE 6

ELECTRICAL AND ACTIVATION WIRING INSTRUCTIONS PAGE 7

WIRING DIAGRAMS:

SLT-4X-R RIGHT HAND, FAIL LOCK PAGE 9

SLT-4X-R-FS RIGHT HAND, FAIL SAFE PAGE 10

SLT-4X-L LEFT HAND, FAIL LOCK PAGE 11

SLT-4X-L-FS LEFT HAND, FAIL SAFE PAGE 12

SLT-6X BI-DIRECTIONAL, FAIL LOCK PAGE 13

SLT-6X-FS BI-DIRECTIONAL, FAIL SAFE PAGE 14

MAINTENANCE PAGE 15

TROUBLESHOOTING PAGE 17

SLT PLAN & ELEVATION VIEW DRAWINGS PAGE 20

EXPLODED PARTS DETAIL PAGE 21

NUMBERED PARTS LIST FOR EXPLODED PARTS DETAIL PAGE 25

LUBRICATION GUIDE PAGE 26

Alvarado – SLT / SLTX Turnstile

IMPORTANT SAFETY PRECAUTIONS

WARNING: Always follow the installation and operating precautions, including the following:

•Read this manual in its entirety before installing or operating the turnstile. If there are

questions, you may contact Alvarado at (909) 591-8431, Monday through Friday, 6:00 AM to

4:30 PM PST.

•Only skilled individuals should install and service the turnstile.

•The turnstile is not a toy. Do not allow children to play on or near the turnstile. Do not allow

horseplay near the turnstile.

•Follow a proper maintenance schedule.

•Do not operate the turnstile if it has been damaged in any manner. Have the turnstile

repaired or adjusted by a skilled service person before use.

•Do not modify or alter the turnstile.

•Do not operate the turnstile unless the hydraulic dampening unit is operating and adjusted

correctly. For information on maintenance and adjustment of the hydraulic dampening unit,

please refer to the Maintenance section of this document.

•Use ONLY Alvarado parts.

•In access control applications, train all personnel that will be using the turnstile in the proper

method of operation. Ensure that as new users are added, they are properly trained.

SAVE THESE PRECAUTIONS

Alvarado – SLT / SLTX Turnstile

TURNSTILE CONFIGURATION DESCRIPTIONS

Entry

TURNSTILE CONFIGURATION

OTHER CONFIGURATIONS DESCRIBED IN DRAWINGS

Right

Handed

Turnstile

Left

Handed

Turnstile

Non-Electric

SLT-3

Three-position key lock control allows turnstile

to remain locked in both directions, unlocked in

either direction or open in both directions.

Electric

SLT-4X

Turnstile is electrically controlled in one

direction and key lock controlled in the

opposite direction. The three-position key

lock control allows the turnstile to remain

locked in both directions, unlocked in either

direction or open in both directions.

SLT-6X

Turnstile is electrically controlled in both

directions. The three-position key lock

control allows the turnstile to remain locked

in both directions, unlocked in either

direction or open in both directions.

Fail Lock (Electric models only)

The turnstile locks when power is removed

(or lost). Turnstile will unlock when both

power and an activation contact are

supplied. This is how the turnstile leaves the

factory unless specified otherwise.

Fail Safe (Electric models only)

The turnstile unlocks in the electrically

controlled directions in the event of power

loss and relocks when power is supplied.

Unlock Override

The unlock override feature allows one or

both directions of passage to be unlocked

with a key (included for both directions on all

SLT models). One key lock for each passage

direction is located near the arms on the

cabinet fascia. Both locks are keyed alike.

Activation (Electric models only)

Alvarado’s turnstile requires a momentary dry

contact of between 25 ms and 0.5 s. The

turnstile will not buffer activations. Once

activated, the turnstile will not accept another

activation until the turnstile arm has been

rotated.

Alvarado – SLT / SLTX Turnstile

OVERVIEW OF INSTALLATION / SLAB REQUIREMENTS

OVERVIEW OF INSTALLATION STEPS:

A. Determine turnstile locations taking into

account power and activation wiring

(if applicable)

B. Anchor turnstile

C. Connect Power (if applicable)

D. Connect Activation Wiring (if applicable)

PARTS REQUIRED

(SUPPLIED BY ALVARADO)

3 each mounting bolts

3 each washers

3 each Anchors

SLAB REQUIREMENTS

MINIMUM THICKNESS: 4” LEVEL SOLID CONCRETE

DO NOT INSTALL ON ASPHALT

Verify layout location.

Note: the turnstile arm should be

approximately 2” from the next unit or

outside barrier.

TOOLS REQUIRED:

Heavy Duty Drill

5/8” Concrete Drill Bit

3/8” Torque Wrench

Hammer

Shop Vac

Tape Measure

Chalk

Shim Material

Safety Glasses

TURNSTILE LOCATION AND BARRIER SPACING

Alvarado – SLT / SLTX Turnstile

INSTALLATION

INSTALLING THE TURNSTILE

1. Place the turnstile in the desired location.

2. Mark the center location of the three anchor holes.

3. Using the impact drill and a 5/8" drill bit, drill a minimum 3" deep hole at the center of each of

the three marked outer anchor locations. For Terrazzo, ceramic tile, or brick veneer installations

add the thickness of the finished floor material to the anchor hole depth (Note: The anchoring

package provided by Alvarado should ONLY be used to anchor the unit directly into the

concrete slab).

4. Vacuum out holes thoroughly. If the holes are not clean, the anchors will not tighten.

5. Insert an anchor into each drilled hole. Ensure that the anchors are flush with the concrete floor.

NOTE: Insert anchors with threads down.

6. Return the turnstile to the install location.

7. Insert a 3/8" bolt and washer through the turnstile base into each of the SB anchors. Tighten the

3/8" bolts to 20 ft-lbs. torque.

8. If the turnstile is uneven or rocks, loosen the bolts, shim the turnstile cabinet as necessary, and

re-tighten the bolts.

Alvarado – SLT / SLTX Turnstile

ELECTRICAL AND ACTIVATION WIRING INSTRUCTIONS

(SLTX Models Only)

TOOLS REQUIRED: Wire Stripper

PARTS REQUIRED: Wire Nuts

INSTRUCTIONS:

(NOTE: ONLY SKILLED ELECTRICIANS SHOULD CONNECT POWER)

1. Make sure that primary power to the unit is off.

2. Locate the wiring diagram for the turnstile model being installed. The model number is

listed on the manufacturer’s serial number plate mounted near the head on the cabinet

fascia. (e.g. SLT-4X-R, SLT-4X-R-FS)

3. Remove the lid.

4. Make electrical and necessary activation connections per the appropriate drawing.If an

optional step down transformer was purchased with the unit, find a suitable location to

install the transformer. DO NOT MOUNT THE TRANSFORMER INSIDE OF THE

TURNSTILE CABINET. An appropriate fuse MUST be used to protect the Input AC

Transformer at all times (use a ¾ AMP 250 VAC Fuse). The following power

requirements must be supplied at the turnstile when operating the turnstile without the

supplied transformer:

A. 18 VAC @ 2 Amps using an AC Source with the supplied rectifier.

B. 24 VDC @ 2 Amps using a DC Source and bypassing the supplied rectifier.

5. Review all electrical wiring and contacts for exposure to any metal parts that may lead to

a short.

6. Manually rotate the turnstile and inspect microswitch contacts to ensure that the switch

arm is depressed but not distorted.

Alvarado – SLT / SLTX Turnstile

7. Turn ON the primary power to the unit. For both fail-lock and fail-safe units, the turnstile

should be locked in the controlled direction(s) when power is applied.

8. Turn OFF primary power. If fail-lock, verify that upon loss of power, the turnstile remains

locked in the electrically controlled direction. If fail-safe, verify that upon loss of power, the

turnstile unlocks in the electrically controlled direction.

9. Turn the primary power back ON and provide the turnstile an activation signal. The

turnstile should unlock. To simulate an activation signal without using a separate

activation device, short the appropriate Activation Leads (see wiring diagram) together.

Short the Activation Leads by undoing the wire nuts and momentarily touching the

appropriate wire ends together. If you choose to simulate the signal, leave the wire nuts

off until step 13.

10. Rotate the turnstile arm in the appropriate direction. If the turnstile is functioning correctly,

the turnstile will automatically relock.

11. Repeat steps 9 and 10 a total of three times.

12. For bi-directionally controlled turnstiles (Model SLT-6X units ONLY), repeat steps 9

through 11 for the opposite direction and confirm correct functionality.

13. Re-attach the turnstile lid.

Alvarado – SLT / SLTX Turnstile

SLT-4X-R RIGHT HAND FAIL LOCK

FRAME CONFIGURATION

SLT-4X-R, RIGHT HAND, FAIL LOCK WIRING DIAGRAM

18 VAC

POWER IN

TRANSFORME

P/N: 10-3003C

(If ordered with the unit)

FUSE

3/4 AMP

250 VAC

120 VAC

Alvarado – SLT / SLTX Turnstile

SLT-4X-R-FS RIGHT HAND FAIL SAFE

FRAME CONFIGURATION

SLT-4X-R-FS, RIGHT HAND, FAIL SAFE WIRING DIAGRAM

18 VAC

POWER IN

TRANSFORME

P/N: 10-3003C

(If ordered with the unit)

FUSE

3/4 AMP

250 VAC

120 VAC

Andere Handbücher für SLT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alvarado Drehkreuz Handbücher

Alvarado

Alvarado SUPERVISOR 3000 Bedienungsanleitung

Alvarado

Alvarado WATCHMAN Bedienungsanleitung

Alvarado

Alvarado EDC Bedienungsanleitung

Alvarado

Alvarado Supervisor 2000 Bedienungsanleitung

Alvarado

Alvarado Supervisor 3500 Bedienungsanleitung

Alvarado

Alvarado TAS12-AS1 Bedienungsanleitung

Alvarado

Alvarado SUPERVISOR 3000 Bedienungsanleitung

Alvarado

Alvarado SU5000 Bedienungsanleitung

Alvarado

Alvarado SLT Gebrauchsanweisung

Alvarado

Alvarado EDM Bedienungsanleitung

Alvarado

Alvarado Supervisor 500 Bedienungsanleitung

Alvarado

Alvarado SUPERVISOR 5000 Bedienungsanleitung

Alvarado

Alvarado TAS12-EDM Bedienungsanleitung

Alvarado

Alvarado MST Gebrauchsanweisung

Alvarado

Alvarado UltraQ-AMT Bedienungsanleitung

Alvarado

Alvarado MSTT-3 Service-Handbuch

Alvarado

Alvarado UltraQ Bedienungsanleitung

Alvarado

Alvarado UltraQ Bedienungsanleitung

Alvarado

Alvarado UltraQ Bedienungsanleitung

Alvarado

Alvarado SW1000 Betriebsanleitung

Alvarado

Alvarado SUPERVISOR 4500 Bedienungsanleitung

Alvarado

Alvarado MT Montage- und Bedienungsanleitung

Alvarado

Alvarado MST-3 Bedienungsanleitung

Beliebte Drehkreuz Handbücher anderer Marken

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

LBA GROUP

LBA GROUP LBAT10 Bedienungsanleitung

Magnetic

Magnetic mTripod Bedienungsanleitung

Kaba

Kaba Argus HSG-E02 Bedienungsanleitung

Automatic Systems

Automatic Systems TR491 Bedienungsanleitung

Turnstiles

Turnstiles HZ-SWGS01 Bedienungsanleitung

DSI

DSI DST-80 Bedienungsanleitung

OZAK

OZAK VP-125 Handbuch

Automatic Systems

Automatic Systems SMARTLANE SL 90X Bedienungsanleitung

JKDC SECURITY

JKDC SECURITY JKDC-100C Bedienungsanleitung

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Bedienungsanleitung

Oxgard

Oxgard Praktika T-04K Kurzanleitung

digicon

digicon CATRAX Plus Bedienungsanleitung

Oxgard

Oxgard CUBE C-04-s Bedienungsanleitung

BOON EDAM

BOON EDAM Turnlock 100 Leitfaden

Wano

Wano Tripod BO-DSN10 Bedienungsanleitung

Timewatch

Timewatch TWLD-TS2700 Bedienungsanleitung

OZAK

OZAK GLASS LINE A1 Bedienungsanleitung