ALW H-BEAM 1.25 Bedienungsanleitung
A1035 22nd Avenue, Unit 1 nOakland, CA 94606 P510.489.2530 ETalkToUs@alwusa.com Walwusa.com
INSTALLATION INSTRUCTIONS
H-BEAM 1.25 / MICRO
Wall Mount
HB1.25 / MICRO Wall Mount Installation Guide 2 of 11 102-000018 - IG020519-A.0
HB1.25 / MICRO - Safety & Warnings!
1. Read all instructions.
2. Install in accordance with national and local electrical code regulations.
3. This product is intended to be installed and serviced by a qualied, licensed electrician.
4. Do not install in wet locations. For dry and damp use only.
5. Turn off electrical power before installing or servicing xture in any way.
6. To reduce the risk of re and overheating, make sure all connections are tight.
7. This product is suitable for continuous row mounting.
1. Lisez toutes les instructions.
2. Installez conformément à la réglementation du code électrique national et local.
3. Ce produit est destiné à être installé et entretenu par un électricien agréé qualié.
4. Ne pas installer à l’extérieur ou dans des endroits humides. Pour une utilisation en intérieur et sec
seulement.
5. Coupez l’alimentation électrique avant de évoluer le système d’éclairage en aucune façon.
6. Pour réduire le risque d’incendie et de surchauffe, assurez-vous que toutes les connexions sont bien
serrées.
7. Peut être monté en rangée continue.
HB1.25 / MICRO - Attention!
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior
to installation or servicing.
HB1.25 / MICRO Wall Mount Installation Guide HB1.25 / MICRO Wall Mount Installation Guide 3 of 11 102-000018 - IG020519-A.0
Table of Contents
Luminaire Overview
Included Parts
Parts (by others)
Tools Required
Installation
Prepare Wall
Connect Wiring
Joining Straight Sections
Wiring Diagrams
Troubleshooting
Diagram
Traditional On/Off
0-10V Dimming
DMX
DALI
Lutron LDE
4
4
4
4
4
5
5
6
8
10
10
10
10
10
10
11
Mount Fixture 7
Quick Specs 4
Finishing (single-section xtures) 7
Finishing (multi-section xtures) 9
HB1.25 / MICRO Wall Mount Installation Guide HB1.25 / MICRO Wall Mount Installation Guide 4 of 11 102-000018 - IG020519-A.0
Included Parts
Luminaire Overview
2” x 4” J-Box for wall
applications
Parts (by others)
Drill
#2 phillips bit
Screwdriver
Tools Required
HB Fixture Wall Mount Brackets
Input Voltage / Frequency:
See product label
Rated Current:
See engineering drawing
Ambient Temperature:
-4° – 120°F (-20° – 50°C)
Environment:
Dry and damp locations
Quick Specs
Level
Wood Screws
6-32 Mounting Screws
HB Fixture
Wall Mount Brackets 6-32 Mounting Screws (x2)
Wood Screws (x4)
2x4 J-Box
To Class 2 Remote Driver
(not pictured)
HB1.25 / MICRO Wall Mount Installation Guide HB1.25 / MICRO Wall Mount Installation Guide 5 of 11 102-000018 - IG020519-A.0
Installation: Prepare Wall
Plan structure
6
1
⁄
8
"
1
11
⁄
16
"
3
3
⁄
8
" 5"
Install Blocking 3 1/8” from intended power-entry end of
xture. Install 2” x 4” in. J-Box into wall as shown(not in-
cluded). Center of J-Box should be approximately 6 1/8”
from intended end of xture and 1 11/16” from intended
top of xture. Install blocking to support other side of
J-box with 5” on-center spacing from rst block.
1AInstall Blocking and J-Box
Review submittal drawings for mounting dimensions.
31⁄8"41⁄8"
Install blocking approximately 4 1/8” from intended
non-power-entry end of xture. See submittal drawings
for full mounting dimensions. If installing multiple sections,
install blocking for entire xture. Install drywall.
1BInstall blocking (Non-Power Entry End)
1
HB1.25 / MICRO Wall Mount Installation Guide HB1.25 / MICRO Wall Mount Installation Guide 6 of 11 102-000018 - IG020519-A.0
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching end
caps.
Installation: Prepare Wall
Screw J-Box wall plate to structure using wood screws.
4Fasten J-Box wall plate to structure
Mount J-Box wall plate to J-Box with 8-32 screws.
3Mount J-Box wall plate to J-Box
Make wiring connections between J-Box (from remote
driver) and xture. See submittal drawings and diagrams
on pg. 10 for complete wiring instruction.
6Connect wiring
Installation: Connect Wiring
Install remote driver J-Box(es) in an accessible/
serviceable location. Run low voltage CL2 or applicable
wire from Remote Driver J-Box to Canopy J-Box in
accordance with local/state/federal regulations.
2Install Remote Driver J-Box
Screw standard wall plate into structure using wood
screws. Ensure standard wall plate is level with J-Box wall
plate.
5Mount standard wall plate
HB1.25 / MICRO Wall Mount Installation Guide HB1.25 / MICRO Wall Mount Installation Guide 7 of 11 102-000018 - IG020519-A.0
10 Illuminate xture
Power xture and check for complete illumination
Installation: Finishing (single section xtures)
9Turn power on
Turn power back on at the breaker.
Raise xture to wall brackets.
7Mount xture to wall
Installation: Mount Fixture
Secure xture to wall plates using provided 6-32 screws.
Ensure xture for strength and alignment.
8Secure Fixture
HB1.25 / MICRO Wall Mount Installation Guide 8 of 11 102-000018 - IG020519-A.0
12 Connect wiring
Connect wiring quick-connects. It may require two
people to install joining sections.
13 Mount xture to wall
15 Secure internal joiner brackets
Using phillips screwdriver, fasten internal brackets. Re-
place heat sink and lens.
Raise xture to mounting bracket and secure using pro-
vided 6-32 screws.
Installation: Joining Straight Sections
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching end
caps.
11 Prepare structure for connecting xture
Install blocking, drywall, and mounting screws as dimen-
sioned in submittal drawings. All mounting points must be
level.
14 Remove lens and heat sink
Carefully remove lens and heat sink to access joiner
brackets.
HB1.25 / MICRO Wall Mount Installation Guide HB1.25 / MICRO Wall Mount Installation Guide 9 of 11 102-000018 - IG020519-A.0
17 Illuminate xture
Power xture and check for complete illumination
Installation: Finishing (multi-section xtures)
16 Turn power on
Turn power back on at the breaker.
HB1.25 / MICRO Wall Mount Installation Guide 10 of 11 102-000018 - IG020519-A.0HB1.25 / MICRO Wall Mount Installation Guide
Wiring Diagrams
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Ground
Line Voltage (Hot)
Line Voltage (Neutral)
L
N
AC 50/60Hz
Traditional On/Off
Remote LED
Driver J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Grey
Purple
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
0-10VDC (Dim-)
0-10VDC (Dim+)
L
N
AC 50/60Hz
DIM-
DIM+
0-10V Dimming
Remote LED
Driver J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Clear
Black
DMX in shield
DMX in -
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
L
N
AC 50/60Hz
DMX In Shield
DMX in -
Red
DMX in +
DMX in +
Clear
Black
DMX out shield
DMX out -
White
DMX out +
DMX Out Shield
DMX out -
DMX out +
DMX
Remote LED
Driver/Decoder
J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Purple
Grey
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
Data +
Data -
L
N
AC 50/60Hz
DATA +
DATA -
DALI
Remote LED
Driver/Decoder
J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Purple
Grey
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
E1
E2
L
N
AC 50/60Hz
E1
E2
Lutron LDE
Remote LED
Driver J-Box
Andere Handbücher für H-BEAM 1.25
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ALW Laterne Handbücher
