Amada MH-5B Bedienungsanleitung
S06M0436E-04
OPERATION MANUAL
HAND-HELD WELDING HEAD
MH-5B
Thank you for purchasing the Amada Miyachi Hand-held Welding Head MH-5B.
Before using this Welding Head, read this operation Manual carefully until you have
familiarized yourself with it.
After reading, keep the manual in a place where operators can refer to it at any time.
If you have any questions during use, refer to this manual.
Contents
[1] For Correct Use.........................................................1
[2] Features .....................................................................4
[3] Specifications and Accessories ..............................4
[4] Name and Function of Each Part.............................4
[5] Connection to Welding Transformer and
Welding Power Supply .............................................5
[6] User’s Maintenance ..................................................6
[7] Outline Drawing ........................................................ 7
-1-
[1] For Correct Use
Safety Precautions
Before using, read “Safety precau-
tions” carefully to understand the
correct method of use.
These precautions are shown for safe use of・
our products and for preven of damage or
tion
injury to operators or others.
Be sure to read each of them, since all of
them are important for safety.
The meaning of the words and symbols is・
as follows:
Denotes operations and practices that may
imminently result in serious injury or loss
of life if not correctly followed.
Denotes operations and practices that may
result in serious injury or loss of life if not
correctly followed.
Denotes operations and practices that may
result in personal injury or damage to the
equipment if not correctly followed.
These symbols denote "prohi-
bition". They are warnings about
actions out of the scope of the
warranty of the product.
These symbols denote actions
which operators must take.
Each symbol with a triangle
denotes that the content gives
DANGER WARNINGnotice of ,
or to the operator.CAUTION
Do not touch the inside of the Welding Head.
You may receive an electric shock or be burned if you touch the inside of
the Welding head unnecessarily.
Never disassemble, repair or modify the Equipment.
These actions can cause electric shock and fire.
-2-
Do not touch any welded part or electrodes during welding and
just after welding finished.
The welded part of a workpiece, electrodes and main shaft are very hot.
Do not touch them; otherwise you may be burnt.
Use proper tools(wire strippers, pressure wire connectors, etc.)
for termination of the connecting cables.
Do not cut the wire conductor. A flaw on it can cause fire and electric shock.
Do not damage the power cable and connecting cables.
Do not tread on, twist or tense any cable. The power cable and connecting
cables may be broken, and that can cause electric shock and fire.
Do not use a damaged power cable, connecting cable or plug.
A damaged cable or a plug can cause electric shock, short circuits and fire.
If any part needs to be repaired, consult Amada Miyachi Co., Ltd. or your
distributor.
Connect the cables securely.
Insecure connection of a cable can cause fire and electric shock.
Stop the operation if any trouble occurs.
Continuous operation after occurrence of a trouble such as burning smell,
abnormal sound, abnormal heat, smoke, etc. can cause electric shock and
fire. If such a trouble occurs, immediately consult Amada Miyachi Co., Ltd.
or your distributor.
Persons with pacemakers must stay clear of the welding
machine.
A person who uses a pacemaker must not approach the welding machine or
walkaroundtheweldingshopwhiletheweldingmachineisinoperation,
without being permitted by his/her doctor. The welding machine generates a
magnetic field and has effects on the operation of the pacemaker while it is
turned on.
Protective gear must be worn.
Put on protective gear such as protective gloves, long-sleeve jacket, leather
n, etc. Spatter can burn the skin if they touch the skin.
apro
Wear protective glasses.
If you look at the flash directly during welding, your eyes may be damaged.
If any spatter gets in your eye, you may lose your eyesight.
-3-
splash water on the Welding Head.Do not
Water splashed over the electric parts, can cause electric shock and short
circuits.
.Keep combustible matter away from the Equipment
Spatter can ignite combustible matter. If it is impossible to remove all
combustible matter, cover them with non-combustible material.
Do not cover this Equipment with a blanket, cloth, etc.
Do not cover this Equipment with a blanket, cloth, etc. while you are using it.
Thecovermaybeoverheatedandburn.
Keep a fire extinguisher nearby.
Keep a fire extinguisher in the welding shop in case of fire.
Maintain and inspect this Welding Head periodically.
Maintain and inspect the Equipment periodically, and repair any damage
nearby before starting operation.
Do not use this Welding Head for any purpose other than
welding.
Use of this Equipment in a manner other than specified can cause electric
shock and fire.
Precautions for Handling
Do not drop or tread on this Welding Head.・
Do not use this Welding Head in the following places:・
Damp places (where humidity is 90% or higher), dusty places, places where chemicals
are handled, places near a high noise source, hot or cold places (where temperatures
are above 40 or below 5 ), and places where water will be condensed.℃℃
Use proper tools (wire strippers, pressure wire connector, etc.) for termination of the・
connecting cables, and take care not to damage the conductors.
Clean the outside of this Welding Head with a soft, dry cloth or one wet with a little water.・
If it is very dirty, use diluted neutral detergent or alcohol. Do not use paint thinner,
benzine, etc., since they can discolor or deform the Equipment.
Do not put a screw, a coin, etc., in this Welding Head, since they can cause a malfunction.・
Operate this Welding Head according to the method described in this operation manual.・
-4-
[2] Features
has the following features.The Amada Miyachi Hand-held Welding Head MH-5B
ince the electrode force can be adjusted steplessly, it can be set finely.・S
Since a stable force is applied to the electrode for each weld , constant weld・
quality is obtained.
Since the electrode responds to follow-up penetration quickly, an expulsion or・()
an excessive indentation is not made and the welded surface is clean.
Since this Welding Head has a rugged construction, reliable and stable weld・
quality is obtained.
Since this Welding Head is small and light, the operator can use it for a long time・
without fatigue.
[3] Specifications and Accessories
Check that all accessories
are provided.Specifications Accessories
Item Electrode rod* 3 Tip: 0.5 2p'csMH-5B-01 φφ()‥‥
Secondary 14mm ,1000mm 2 p'csElectrode 0.5 5.5kgf～
2
‥
cable
force Steplessly adjustable()
pieceForcing 1Spring Grounding 200 by 30mm ‥‥
plate 2mm thick
method
3 Tip: 0.5 Operation 1 copyElectrode dia.φφ()
manual
()Allowable 30 Ws At 2% duty cycle
A1C and inverter * One electrode is factory-attached.weld energy ()
Mass 200g
Outline See outline drawing
[4]NameandFunctionofEachPart
Electrode (CrCu)①
The electrode for spot
welding.
Main shaft②
The conductor to hold
the electrode. Retracts
when a pressure is
applied.
Fixing screw③
Secures the electrode.
-5-
Weld force scale④
Indicates the approximate
force exerted.
Be sure to hold the to use this⑤Body Body
Handle with care the metalWelding Head.
parts and the secondary cable
⑥Cover ()①②③
because they get hot. Do not place
metallic such as a watch, tool, etc.,⑦Secondary cable anything
around this Head during operation, becauseConnects this Head and
. Two it may be broken and can injure you.welding controller
14mm andcables of
２
1000mm long is attached.
ATTENTION
Start cable⑧
If anything metallic, such as a screwdriver, wire, etc.,Connects to the Start
touches metallic portion it may be welded toSwitch connector of the ()①②③
this Welding Head.
welding controller.
Do not place anything metallic around this WeldingDoes not have polarity.
Head during operation.
Grounding plate⑨
A conductor to ground.
[5] Connection to Welding Transformer and
Welding Power Supply
-6-
[6] User's Maintenance
1. Replacing electrode
When replacing the electrode, observe the following procedures:
If a welding current flows during electrode replacement, injury
or breakage may result. When replacing the electrode, be
sure to turn off power supply of the welding controller.
Loosen the fixing screw and pull out the①
electrode.
Insert the replacement electrode into the②
main shaft.
Tighten the fixing screw.③
2. Adjusting weld force
Secure the cover and turn the Body to adjust weld force.
For the relationship between the weld force scale and the actual weld force, see the
Weld Force Conversion Graph.
Weld Force Conversion Graph
←
NOTE
GraphThe Weld Force Conversion
indicates the theoretical values.
Use a pressure gauge or a spring
balance to measure the actual
pressure.
Line-up the center of the screw
andtheweldforcescaletoadjust
theweldforce.
When you set the weld force to
the minimum or the maximum,
the indicator may be damaged
if you try to adjust beyond the
scale.
Weld force
decrease
Weld force increase
-7-
[7] Outline Drawing
Inhaltsverzeichnis
Andere Amada Schweißsystem Handbücher
Amada
Amada WELD CHECKER MM-400A Bedienungsanleitung
Amada
Amada MM-L400A Bedienungsanleitung
Amada
Amada ML-2350AF Bedienungsanleitung
Amada
Amada HF-2500A Bedienungsanleitung
Amada
Amada TA-150AC/300WC Bedienungsanleitung
Amada
Amada ML-3030AS Bedienungsanleitung
Amada
Amada MA-660A Bedienungsanleitung
Amada
Amada MH-H500D Bedienungsanleitung
Amada
Amada PU-G Bedienungsanleitung
Amada
Amada MH-1H-01 Bedienungsanleitung
Amada
Amada IPB-5000B Bedienungsanleitung
Amada
Amada MF-C2000A Series Bedienungsanleitung
Amada
Amada ST-100A Bedienungsanleitung
Amada
Amada TCW Bedienungsanleitung
Amada
Amada MEA-100B Bedienungsanleitung
Amada
Amada Miyachi Unitek STA-200A Bedienungsanleitung
Amada
Amada HF28/240 Bedienungsanleitung
Amada
Amada ML-2650B Bedienungsanleitung
Amada
Amada UB25 Bedienungsanleitung
Amada
Amada Delta Bedienungsanleitung
Beliebte Schweißsystem Handbücher anderer Marken
TAFA
TAFA 30*8B35 Bedienungsanleitung
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung
ESAB
ESAB Buddy Arc 145 Bedienungsanleitung
CIGWELD
CIGWELD 636804 Kurzanleitung
Red-D-Arc
Red-D-Arc DC-400 Bedienungsanleitung
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung
