Amada ML-2350AF Bedienungsanleitung

Z06OM1173717-10

OPERATION MANUAL

Original instructions

YAG LASER WELDER

ML- -CE

2350AF

2351AF

ML-2350AF/2351AF

Thank you for purchasing our YAG Laser Welder ML-2350AF/2351AF.

ML-2350AF-CE and ML-2351AF-CE are the air-cooled versions of the standard

ML-2350A-CE and ML-2351A-CE, respectively. This operation manual describes only the

difference of the air-cooled versions from the standard ones.

See the operation manual of the standard version for how to use, such as operation

method.

Contents

1. Difference from the Standard Specifications......1

2. Specifications .......................................................1

3. Maintenance ..........................................................4

4. Outline Drawing ....................................................6

In this manual, ML-2350AF denotes ML-2350AF-CE;

ML-2351AF, ML-2351AF-CE.

ATTENTION

ML-2350AF/2351AF

- 1 -

1. Difference from the Standard Specifications

The laser power supply, oscillator head and cooler are accommodated in one body.

Transportation and installation are easy because the piping for city water is not

necessary.

The air-cooled system does not waste water resources.

How to operate is just the same as the standard ML-2350A-CE and ML-2351A-CE.

2. Specifications

①Specifications List

Oscillator

ML-2350AF ML-2351AF

Maximum rated output 70W 50W

Maximum output energy 70J/P

(10ms Pulse width)

50J/P

(10ms Pulse width)

Maximum peak power 7kW 5kW

Pulse width Standard: 0.3–30.0ms (0.1ms steps)

Fine setting: 0.25–5.00ms (0.05ms steps)

Pulse Repetition 1–200pps

Oscillation wavelength 1.064μm

Resonator shutter With open/close sensor

Positioning guide beam Built-in visible laser (Red)

Output stability *1 ±3%

Power supply 3-phase, 400V AC±10%, 50/60Hz

Max. input current 6.5A

Max. apparent power 4.5kVA

Power consumption Maximum: 3.5kW / Stand-by: 0.49kW

Breaker rated current (to

be supplied by customers)

For the power supply side, we earnestly recommend

using a leakage breaker with the rated current of 10 A

or more, which is applicable to harmonics and surges.

Ground Class C (ground resistance: 10 Ωmax.)

Cooler

Heat exchange method Forced air-cooled

Operating room

temperature

5°–30°C (40°C max. cooling water temp.)

The temperature may varies depending on LAMP

INPUT POWER (%) of 80% or higher and installation

conditions. Refer to the Cooling Capability Chart below.

(Provide the provision to measure the difference

between room and coolant temperatures.)

NOTE: Heat of 2.5

kW (2150

kcal/h) is discharged for the maximum rating.

The ML-2350AF/2351AF eliminates city water to improve the factory environment.

ML-2350AF/2351AF

- 2 -

Laser

Controller

MLE-118A

Schedule setting

Up to 32 schedules can be set by combining

・Laser output waveform

・Laser energy for upper/lower limit judgment

・Number of outputs per second

・Number of repeated outputs

Measurement function Laser energy (J)

Average power (W)

Counter Displays total number of outputs (9 digits)

Displays the number of acceptable outputs (9 digits)

Length of cable Standard 3m cable

Others Mass Approx. 250

Dimensions 990 (H) x 521.1 (W) x 995 (D) mm

*1) Under the condition that laser output energy is at least 5

J per pulse and peak power is at

least 1

kW.

②Cooling Capability

The chart at left depicts the

cooling capability at 100%

duty cycle. Do not use in

room temperature exceed-

ing the line shown.

See the examples below

for less than 100% duty

cycle:

[Example 1]

Letting LAMP INPUT POWER be 60%, and “1-s laser output—2-s pause” be repeated.

60 x 1/3 = 20

LAMP INPUT POWER of 20% gives the room temperature of about 36C.

Keep room temperature 36C or less.

[Example 2]

Letting LAMP INPUT POWER be 80%, and “3-s laser output—2-s pause” be repeated.

80 x 3/5 = 48

LAMP INPUT POWER of 48% gives the room temperature of about 33.5C.

Keep room temperature 33.5C or less.

0% 20% 40% 60% 80% 100%

LAMP INPUT PWR

Room temperature

（℃）

Ex. 2

Ex. 1

LAMP INPUT POWER

are measured and displayed.

ML-2350AF/2351AF

- 3 -

③Clearances between the Laser and Surrounding Wall

ML-2350AF/2351AF are provided with vents on its left and rear sides for heat

radiation. Install the Laser to secure the minimum clearances of 500

mm as shown;

otherwise, full performance cannot be expected.

500mm

Front

Exhaust

45°

Suction

Exhaust

If you cannot provide clearances specified above, consult us.

ML-2350AF/2351AF

- 4 -

3. Maintenance

(1) Maintenance Parts and Standard Intervals of

Inspection/Replacement

In addition to maintenance parts for the standard model, perform inspection

periodically referring to the following table.

Part name Model No. Item No. Operation interval

(standard) (*1)

Contents of

operation (*2)

Air filter (side) Z-01641-001 1018369 Every week Clean

1 year Replace

*1: The operation interval means the maintenance time or expected life of the part,

and is different from the guarantee period.

*2: Part replacement is performed when any damage or defect is found or the

usable period ends.

ML-2350AF/2351AF

- 5 -

(2) Maintenance of the Air Filter (Side)

The air filter at the side of the main unit is provided at the air inlet of the radiator.

Perform cleaning for this air filter at this portion every week.

Item required

Phillips screwdriver

Operating Procedure

(1) Remove screws of the filter cover at the side of the main unit.

Filter Cover

Screw

(QTY.6) Air Filter

Cover

(2) Take out the filter and wash it in tap water. Then, dry the air filter completely.

When the air filter is very dirty, use a neutral cleaner.

(3) Install the air filter by using the filter cover.

ML-2350AF/2351AF

- 6 -

4. Outline Drawing

The Laser Outline and Location of Warning/Caution Label

See the next page for details of warning labels.

CONTROL

SHUTTER

OFF

213456

POWER

HIGH VOLTAGE

READY

MAIN SHUTTER

990

995

495

521

⑥

②

⑤

①

④

③③⑤②

②

⑦

②

(

Dimensions in mm

)

ML-2350AF/2351AF

- 7 -















Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Amada Schweißsystem Handbücher

Amada

Amada MH-1H-01 Bedienungsanleitung

Amada

Amada LW500A Bedienungsanleitung

Amada

Amada ML-2350A-CE Bedienungsanleitung

Amada

Amada UB25 Bedienungsanleitung

Amada

Amada TL-180B Bedienungsanleitung

Amada

Amada Delta Bedienungsanleitung

Amada

Amada MH-D500D Bedienungsanleitung

Amada

Amada IPB-5000B Bedienungsanleitung

Amada

Amada AH Series Bedienungsanleitung

Amada

Amada MH-H500D Bedienungsanleitung

Amada

Amada HF28/240 Bedienungsanleitung

Amada

Amada MA-660A Bedienungsanleitung

Amada

Amada ML-2350AF-CDRH Bedienungsanleitung

Amada

Amada MH-5B Bedienungsanleitung

Amada

Amada Delta Bedienungsanleitung

Amada

Amada MF-C300A-SF Bedienungsanleitung

Amada

Amada ML-3030AS Bedienungsanleitung

Amada

Amada MD Series Bedienungsanleitung

Amada

Amada MA-520B Bedienungsanleitung

Amada

Amada 301H/115V Bedienungsanleitung

Amada

Amada MEA-100B Bedienungsanleitung

Amada

Amada WELD CHECKER MM-400A Bedienungsanleitung

Amada

Amada ML-2650B Bedienungsanleitung

Amada

Amada ML-7 Series Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung