AmazonBasics B00MIBN16O Bedienungsanleitung

AmazonBasics Desk Monitor Mount

B00MIBN16O

English . . . . . . . . . . . . . . . . . . . . . .3

Français . . . . . . . . . . . . . . . . . . . .17

Deutsch . . . . . . . . . . . . . . . . . . . .31

日本語 . . . . . . . . . . 45

中文. . . . . . . . . . . . . . . . . . . . 59

Italiano . . . . . . . . . . . . . . . . . . . . .72

Español. . . . . . . . . . . . . . . . . . . . .86

English

Instruction Manual · English

AmazonBasics Desk Monitor Mount

Contents

Make sure that the package contains the following parts:

Upper arm

(1 pc)

Bracket cover

(1 pc)

Grommet bracket

(1 pc)

M8 (1/4-20UNC, 3 inch)

(1 pc)

Wing nut

(1 pc)

Cable tie

(2 pcs)

M4 × 10 mm screw

(4 pcs)

Lower arm

(1 pc)

M4 × 10 mm knob

(4 pcs)

Base

(1 pc)

4 mm Allen wrench

(1 pc)

2.5 mm Allen wrench

(1 pc)

M3 x 6 mm

screw

1 (pc)

Supported monitor weights

Your monitor mount supports a monitor of the following weight:

Monitor adjustments

Your monitor mount lets you adjust the monitor viewing angle, height, tilt, and orientation

(portrait or landscape).

5 to 25 lbs

(2.3 to 11.3 kg)

lbs

360°

180°

360° 13 in.

(330 mm)

70°

5°

Viewing angle Height Tilt Orientation

Assembly Instructions

Step 1: Choose a mounting option.

You can mount the monitor arm using the:

• Desk-clamp mount to attach your monitor arm to the edge of a tabletop. Go to

“Desk-clamp mount” on page 6.

• Plate mount to attach your monitor mount to an area that is away from the edge of a

tabletop. This mounting option requires a hole through the mounting surface. Go to

“Plate mount” on page 7.

Caution: Because mounting surface materials

can vary widely, make sure that the mounting

surface is strong enough to handle your monitor

mount and the monitor.

Desk-clamp mount

Step A: Determine the thickness of the mounting surface, then use the 4 mm Allen wrench to

adjust the location of the mounting clamp assembly, if necessary.

•Thetop screw holes on the clamp bracket fit a mounting surface thickness of less than

5/8 in. (1.6 cm).

•Themiddle screw holes on the clamp bracket fit a mounting surface thickness between

1/4 to 1 5/8 in. (0.6 to 4.1 cm).

•Thebottom screw holes on the clamp bracket fit a mounting surface thickness between

1 1/4 to 2 5/8 in (3.2 to 6.7 cm).

Step B: Slide the mounting clamp assembly onto the mounting surface, then tighten the

clamp.

Caution: Do not rotate the monitor past the

edge of desk. The weight of the monitor may

cause the desk to tip over.

<3/8 in. (1 cm) 1/2 to 1-3/8 in.

(1.2 to 3.56 cm) 1.5 to 2-3/8 in.

(3.7 to 6.0 cm)

4 mm Allen wrench

Plate mount

Step A: Remove the mounting clamp assembly from the clamp bracket on the base.

Step B: Remove the clamp bracket from the base. Keep the screws you remove. You will use

them later.

Step C: Make sure that the side of the grommet bracket with recessed screw holes is facing

down. Insert the M8 × 3 in. screw through the square hole in the center of the grommet

bracket.

Note: To keep the 3-inch screw from falling inside the base, temporarily attach the wing nut to

hold it in place.

4 mm

Step D: Attach the grommet bracket to the base with the 3 screws you removed from the

clamp bracket.

Note: If the screws are not flush to the grommet bracket, the grommet bracket is upside down.

Remove these screws and the M8 × 3 in. screw, turn the grommet bracket over, then put all the

screws back in.

Step E: Remove the clamp plate from the clamp assembly using a Phillips screwdriver.

Step F: Center the base over the top of the hole in the mounting surface, then, from the

bottom of the mounting surface, slide the clamp plate you removed onto the M8 × 3 in. screw.

Secure the clamp plate to the screw with the wing nut.

Note: The M8 × 3 in. screw must be centered in the hole.

Caution: For secure arm attachment and to

avoid equipment damage, the base and the

clamp plate must make contact with the

mounting surface on both sides of the hole.

4 mm

0.31 to 2 in.

(8 to 51 mm)

< 2.25 in.

(57 mm)

Step 2: Determine the orientation of the monitor

You can mount the monitor in a locked portrait or landscape orientation, or you can leave the

monitor free to rotate 360°.

• If you want the monitor to rotate freely, do not insert the M3 x 6 mm screw.

• If you want the monitor in a locked orientation, insert the M3 x 6 mm screw into the front

of the plate on the upper arm.

Note: If you insert the screw, then want to change the monitor’s orientation after you mount the

monitor to the upper arm, you need to remove the monitor from the upper arm and insert or

remove the M3 x 6 mm screw.

Monitor rotates freely.

Monitor is locked in portrait or

landscape orienation.

Step 3: Attach the upper arm to the back of the monitor using a Phillips screwdriver.

Note: If a stand is attached to the monitor, remove the stand.

Note: You can use the M4 × 10 mm screws or M4 × 10 mm knobs to attach the arm to the

monitor.

Caution: The mounting screw holes on the

back of the monitor may require screws of a

different type or length than the provided

M4 × 10 mm screws or knobs.

• Using screws of that are too big in

diameter will damage the screw holes on

the monitor.

• Using screws that are too small or too

short may cause the monitor to fall off the

arm.

• Using screws that are too long may

damage the interior of the monitor.

Before you attach the monitor to the upper arm,

make sure that the provided screws or knobs fit

the screw holes on the back of the monitor.

If the provided screws or knobs do not fit, refer

to the documentation that came with the

monitor for the correct screw type and size.

Warning: The upper arm is under

tension and will move up rapidly, on its

own, as soon as the attached monitor is

removed. For this reason, remove the upper

arm, lay the monitor face down on a soft

surface, then remove the monitor. Failure to

follow this instruction may result in serious

personal injury or equipment damage.

M4 × 10 mm screws M4 × 10 mm knobsOR

Inhaltsverzeichnis

Sprachen:

Andere AmazonBasics Rack & Stand Handbücher

AmazonBasics

AmazonBasics WISHR-003 Bedienungs- und Sicherheitshinweise

AmazonBasics

AmazonBasics B072Y2S76T Bedienungsanleitung

AmazonBasics

AmazonBasics B082Z3BQRJ Bedienungsanleitung

AmazonBasics

AmazonBasics B0799G89Yb Bedienungsanleitung

AmazonBasics

AmazonBasics B09JWR8PG2 Bedienungsanleitung

AmazonBasics

AmazonBasics B076B3WFCD Bedienungsanleitung

AmazonBasics

AmazonBasics B07PZ8KKV9 Bedienungs- und Sicherheitshinweise

AmazonBasics

AmazonBasics B07YZT28BP Bedienungsanleitung

AmazonBasics

AmazonBasics B01KBEOAIW Bedienungsanleitung

AmazonBasics

AmazonBasics Performance B07QH7KDY5 Bedienungsanleitung

AmazonBasics

AmazonBasics B07QJCQYTW Bedienungsanleitung

AmazonBasics

AmazonBasics B018FCZBMG Bedienungs- und Sicherheitshinweise

AmazonBasics

AmazonBasics B07HKJJFKH Bedienungsanleitung

AmazonBasics

AmazonBasics B072Y4BH7D Bedienungs- und Sicherheitshinweise

AmazonBasics

AmazonBasics B07428RCLY Bedienungsanleitung

AmazonBasics

AmazonBasics B082B4W9XW Bedienungsanleitung

AmazonBasics

AmazonBasics B072ZHX3FN Bedienungsanleitung

AmazonBasics

AmazonBasics B07FF48GRY Bedienungsanleitung

AmazonBasics

AmazonBasics B07QKFQ1T1 Bedienungsanleitung

AmazonBasics

AmazonBasics B07R57SVFG Bedienungsanleitung

AmazonBasics

AmazonBasics B07V3QLMS9 Bedienungsanleitung

AmazonBasics

AmazonBasics B083T53K3P Bedienungsanleitung

AmazonBasics

AmazonBasics B01KBEOM2G Bedienungsanleitung

AmazonBasics

AmazonBasics B00QG7W1YY Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung